Study guide

6.3 Cam Bearings, Lobe Lift and Endplay

ASE T1 — Gasoline Engines Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Introduction & ASE T1 Exam Overview

1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy

2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust

2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds

3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing

3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing

4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools

4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service

5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair

5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service

6 Chapter 5: Engine Block Diagnosis and Repair

6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection

7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair

7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators

8 Chapter 7: Ignition System Diagnosis and Repair

8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning

9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair

9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service

10 Chapter 9: Emissions Control Systems Diagnosis and Repair

10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures

11 Chapter 10: Computerized Engine Controls Diagnosis and Repair

11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation

6.3 Cam Bearings, Lobe Lift and Endplay

Key Takeaways Explain This Topic AI

Select and index each cam bearing using the actual block oil-routing instructions.

Theoretical gross valve lift equals lobe lift times the stated rocker ratio.

Inspect a sealed retainer oil passage only on engines that use that design.

Last updated: October 2026

Note

Camshaft dimensions, oil-hole positions and timing-set examples in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.

In-Block Camshaft, Cam Bearings, Lifters & Timing Chain/Gear Service

Many medium- and heavy-duty gasoline truck engines—including the GM 6.0L/6.6L Vortec/L8T and Ford 7.3L V8—use an in-block (cam-in-block) pushrod architecture because it packages high displacement, massive low-RPM torque, and a compact external width inside a rigid deep-skirt cast-iron block. Because the camshaft tunnel sits deep inside the cylinder block valley and shares pressurized oil galleries with the crankshaft main bearings and hydraulic roller lifters, precision inspection of the camshaft bearings, lobe geometry, lifter guides, and timing drive is essential.

  • In-Block Camshaft Bearings & Camshaft Metrology (Task C.4)
  • One-Piece Sleeve Camshaft Bearings: Stepped ODs & Oil Hole Alignment

Unlike two-piece split main and rod bearings, in-block camshaft bearings are one-piece babbitt-lined steel sleeves pressed into machined tunnels in the cylinder block webs using a long mandrel bar, expanding collet/cone, and driver handle:

Progressively Stepped Outer Diameters (OD) : Even when all five camshaft journals share the exact same diameter, the outer diameters of the block cam bearing bores on many truck V8s are stepped progressively larger from rear (#5) to front (#1) (or grouped by specific journal position). This stepped tunnel design allows the smaller rear cam bearings to slide cleanly through the front bearing bores during installation without scratching the block housings. Before driving any cam bearing into the block, lay out the full bearing set in numerical order and verify each bearing's part number and outer diameter with a micrometer.

Cam Bearing Oil Hole Alignment & Clocking : Every cam bearing has one or more drilled oil feed holes that must register with the vertical oil passages connecting the main bearing saddles to the camshaft tunnel and upper lifter galleries. On blocks without an annular groove behind the cam bearing, misaligning the oil hole by even half a hole diameter restricts oil flow to the journal and can starve the entire bank of hydraulic lifters. On blocks that incorporate a 360° circumferential oil groove machined into the block bore behind the cam bearing, OEM procedures specify clocking the bearing oil hole at a precise angle—typically the 2 o'clock or 5 o'clock position looking from the front of the engine—so incoming oil enters the unloaded hydrodynamic zone just ahead of the downward valve-spring load vector at the 6 o'clock bottom dead center of the bearing.

Rear Camshaft Expansion Plug : Always install a new cup-type rear camshaft bore plug at the back of the block sealed with a light film of anaerobic or non-hardening sealant, driven straight to the specified recess depth so the rear of the camshaft neither rubs the plug nor leaks engine oil into the bellhousing.

Measuring Camshaft Lobe Lift, Journal Wear & Runout

Camshaft lobes on heavy-duty truck engines can be measured either in the engine block prior to teardown or on the bench after removal:

In-Block Dial Indicator Method : Remove the rocker arms and mount a magnetic-base dial indicator on the cylinder head deck with a long probe extension resting directly in the pushrod seat of the lifter (or on the tip of the pushrod) strictly parallel to the lifter bore axis. Rotate the crankshaft slowly in the normal direction of rotation until the lifter rests on the lowest point of the cam lobe ( base circle / heel ), zero the dial indicator, and continue rotating the crankshaft until the lobe reaches peak lift ( nose ). The maximum reading is camshaft lobe lift .

Out-of-Block Outside Micrometer Method : Using a 1 to 2 in. or 2 to 3 in. outside micrometer, measure across the cam lobe from the tip of the nose to the opposite heel ( Major Diameter, A ) , then rotate the micrometer 90° to measure across the round base circle ( Minor Diameter, B ) :

  • Camshaft Lobe Lift = Nose-to-Heel Major Diameter (A) - Base Circle Diameter (B)
  • Theoretical Gross Valve Lift = Camshaft Lobe Lift × Rocker Arm Ratio

Measurement Parameter Inspection Tool & Setup Typical Service Limit / Specification

Camshaft Lobe Lift Loss Dial indicator in lifter socket OR outside micrometer ( A - B ) Maximum 0.002 to 0.003 in. ( 0.05 to 0.08 mm ) variation from spec

Camshaft Journal Diameter & Out-of-Round Outside micrometer at four points per journal Journal taper or out-of-round max 0.0010 in. ( 0.025 mm )

Camshaft Journal Oil Clearance Journal OD subtracted from installed cam bearing ID (bore gauge) 0.0015 to 0.0040 in. ( 0.038 to 0.102 mm )

Camshaft Bend (Journal Runout) Outer journals on V-blocks; dial indicator on center journal Maximum 0.0015 to 0.0020 in. ( 0.038 to 0.050 mm ) TIR

Camshaft Axial Endplay Dial indicator on cam snout while prying sprocket fore and aft 0.0015 to 0.0060 in. ( 0.038 to 0.152 mm )

Worked Example: Camshaft Lobe Lift & Gross Valve Lift Calculation Scenario

A technician removes the camshaft from a 6.6L truck V8 that uses 1.7:1 ratio pedestal rocker arms. The stated example specification calls for an intake lobe lift of 0.295 in. ( 0.5015 in. gross valve lift) with a maximum allowable lobe wear loss of 0.0025 in. . Measuring the #3 intake lobe with a calibrated outside micrometer yields:

Nose-to-Heel Major Diameter ( A ) : 1.7660 in.

Base Circle Minor Diameter ( B ) : 1.4755 in.

Actual Lobe Lift : 1.7660 in. - 1.4755 in. = 0.2905 in.

Lobe Wear Loss : 0.2950 in. (Spec) - 0.2905 in. (Actual) = 0.0045 in. (exceeds the 0.0025 in. limit by 0.0020 in. ).

Actual Gross Valve Lift : 0.2905 in. × 1.7 = 0.49385 in. (a loss of 0.00765 in. at the valve tip).

Diagnosis : Inspection of the #3 intake lobe nose reveals subsurface Hertzian fatigue spalling (flaking pits) —the classic failure mode of a hardened steel roller camshaft lobe—caused by a seized needle bearing in the #3 intake roller lifter. Both the camshaft and the lifters must be replaced.

Camshaft Thrust/Retainer Plate & Axial Endplay

In-block roller camshafts are held axially by a hardened steel camshaft thrust/retainer plate bolted to the front face of the cylinder block behind the camshaft timing sprocket. Check camshaft endplay ( 0.0015 to 0.0060 in. ) with a dial indicator mounted on the front of the block while prying the camshaft sprocket gently rearward and forward.

Important

Inspect or replace the camshaft thrust/retainer plate and its seals according to the identified engine procedure. Some designs have a bonded seal on the back of this plate that bridges the high-pressure main-to-lifter oil crossover passages. When heat ages and flattens this orange gasket, pressurized oil sprays directly out from behind the retainer plate into the timing cover—causing an internal oil leak and potentially reduced hot oil pressure and loud upper-engine lifter ticking even when the oil pump and main bearings are in like-new condition.