Study guide
9.2 Fuel Tanks, Lines and Fuel Quality
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
9.2 Fuel Tanks, Lines and Fuel Quality
Key Takeaways Explain This Topic AI
Check dual-tank transfer and selector operation before assuming the tank supplying the engine is full.
Use the gasoline sample volume and tester calibration when estimating alcohol content.
EPA's E15 authorization excludes heavy-duty engines; use the vehicle-approved fuel.
Last updated: October 2026
Note
Fuel Tanks, Lines and Fuel Quality uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
- Fuel Tanks, Dual-Tank Transfer Systems, Lines & Fuel Quality Testing (Task F.3)
- Commercial Truck Fuel Tanks, Venting & Dual-Tank Plumbing
Medium- and heavy-duty gasoline cab-chassis, utility, and box trucks utilize frame-mounted steel or cross-linked polyethylene ( XLPE ) midship and aft-of-axle fuel tanks secured by heavy steel straps lined with rubber anti-chafe isolator strips . During inspection ( Task F.3 ), verify that rubber strap isolators are intact (missing isolators trap road grit and wear pinholes through steel tanks), check the filler neck anti-siphon screen and grounding strap, test the fuel cap two-way pressure/vacuum relief valve, and inspect nylon quick-connect fuel lines for kinks, frame rub-through, or heat degradation near exhaust pipes (always replace damaged nylon sections using OEM-approved nylon repair unions or complete pre-formed assemblies—never splice high-pressure EFI lines with standard low-pressure carbureted rubber hose and worm-gear clamps!).
Many commercial cab-chassis trucks feature dual fuel tanks : a primary midship tank housing the high-pressure fuel delivery module, and an auxiliary rear tank equipped with an electric transfer pump (or a 6-port motorized selector/shuttle valve ). If the auxiliary transfer pump fails, its fuse blows, or the selector valve sticks mid-stroke, the engine stalls with a fuel-starvation no-start as soon as the primary tank runs dry—even when the auxiliary tank is completely full.
Fuel Quality, Phase Separation, Alcohol Content & Volatility Testing
Whenever fuel contamination is suspected, draw a fuel sample from the very bottom of the fuel tank (not from the upper fuel rail if water is suspected, as water settles to the tank floor) into a clean, clear glass cylinder:
Water Contamination & Ethanol Phase Separation : Pure gasoline has a specific gravity of ~0.72 to 0.76 , whereas water is 1.00 . In ethanol-blended gasoline ( E10 ), the ethanol keeps up to ~0.5% water dissolved in suspension. Once water ingress (from condensation or a leaky filler cap/station tank) exceeds that threshold, phase separation occurs: the hydrophilic ethanol bonds with the water and drops to the bottom of the tank as a dense, cloudy or clear water-ethanol slurry . The fuel pump pickup sock sits at the bottom of the tank and draws in this non-combustible, highly corrosive slurry—causing an immediate no-start or severe misfire and corroding fuel injectors—while the upper gasoline layer is left depleted of 3 to 4 octane points , causing severe spark knock.
Diesel Fuel Cross-Contamination : If diesel fuel is accidentally pumped into a gasoline truck tank, the sample looks dark yellow/amber, smells heavy and pungent, and leaves a persistent greasy, oily ring on glass or a paper towel after the gasoline evaporates. Diesel is not formulated for gasoline spark-ignition combustion and vaporization, diesel contamination can cause violent detonation (spark knock) under load, severe power loss, fouled spark plugs, crankcase oil dilution, and thick white/gray exhaust smoke .
Alcohol (Ethanol) Percentage Graduated Cylinder Test :
Procedure : Using a calibrated alcohol-content graduated glass cylinder (or a 100 mL graduated tube), first pour clean water up to the baseline reference mark (for example, 10 mL on a 100 mL tube, or the 25% baseline line on a dedicated tester). Next, fill the tube to the 100 mL ( 100% ) top mark with the suspect gasoline sample ( 90 mL of fuel). Cap the cylinder tightly, shake vigorously for 30 to 60 seconds , and stand it upright on a flat bench for 5 to 10 minutes .
Principle & Calculation : Because ethanol molecules are polar and hydrophilic (water-loving), ethanol partitions into the water-rich layer; extraction completeness and volume contraction affect accuracy of the non-polar gasoline and dissolves into the bottom water layer, causing the visible boundary line between the bottom water/ethanol layer and the upper gasoline layer to rise. Subtract the initial water baseline volume from the new lower-layer volume to find the ethanol content (on a calibrated tester, read the percentage scale directly at the boundary line). Standard non-flex-fuel commercial truck engines are calibrated for a maximum of 10% ethanol ( E10 ) .
Reid Vapor Pressure ( RVP ) & Seasonal Volatility (Vapor Lock) :
Refineries adjust gasoline volatility—measured as Reid Vapor Pressure ( RVP in psi at 100°F / 37.8°C ) —by season: winter-blend fuel ( 11.5 to 15.0 psi RVP) contains more volatile light hydrocarbons (butane) to aid sub-zero cold vaporization, while summer-blend fuel ( 7.0 to 9.0 psi RVP) evaporates much more slowly to prevent boiling in summer heat.
If a seasonal municipal or snow-plow truck sits with high-RVP winter-blend fuel in its tank and is worked hard on a 95°F summer day , the volatile fuel boils into vapor inside the hot engine-bay fuel rail ( vapor lock ) . Because injectors are calibrated to meter incompressible liquid fuel rather than compressible vapor bubbles, the engine suffers hard hot restarts, rough idle, and lean surging under load .
Warning
Worked Diagnostic & Calculation Scenario — Misfueled Utility Truck ( P0171 & P0174 ): A non-flex-fuel 6.6L V8 utility truck is towed in with a rough cold start, lean hesitation, and both P0171 (Bank 1 Lean) and P0174 (Bank 2 Lean) . Scan tool data shows LTFT at +29% on Bank 1 and +30% on Bank 2 at both curb idle ( 650 RPM ) and 2,500 RPM , while fuel rail pressure is a steady 58 psi . Because both banks are equally lean at all speeds and fuel pressure is normal, the technician performs a graduated cylinder ethanol test ( 10 mL water baseline + 90 mL fuel sample = 100 mL total). After shaking for 60 seconds and settling for 10 minutes , the lower water/alcohol boundary rises from 10 mL up to 41.5 mL .
Ethanol Volume Extracted : 41.5 mL - 10.0 mL = 31.5 mL of ethanol out of the 90 mL fuel sample ( 31.5 / 90 × 100 = 35% in an idealized volume calculation, not a laboratory result ethanol!).
Conclusion : The sample indicates excessive alcohol under the stated idealized calculation; it does not identify the exact fuel source, exceeding the engine's 10% ( E10 ) maximum limit and exhausting the PCM's positive fuel trim authority. Draining the tank, refilling with fresh E10 87-octane gasoline, and resetting fuel trim adaptives restores LTFT to +2% .
Source Check — October 13, 2026
EPA excludes heavy-duty engines from its E15 authorization; use the vehicle-approved gasoline blend. Manufacturer or regulator reference .