Study guide
3.4 Dry, Wet and Running Compression
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
3.4 Dry, Wet and Running Compression
Key Takeaways Explain This Topic AI
Keep cranking speed and test preparation consistent across cylinders.
An 80% minimum-of-highest rule permits a 20% reduction, not a fixed psi difference.
Meter only the approved wet-test oil amount and prevent liquid lock.
Last updated: October 2026
Note
Dry, Wet and Running Compression uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
Cranking (Dry) and Wet Compression Testing (ASE T1 Task A.8)
Once power balance or Mode \$06 misfire data points to one or more weak cylinders, a cranking compression test isolates whether the fault is mechanical cylinder sealing.
Mandatory Five-Step Test Preparation
Skipping any preparation step skews pressure readings across the bank and can cause catalyst damage or engine bay fires:
Normal Operating Temperature ( 190°F–210°F ): Warm the engine completely so pistons, rings, cylinder walls, and valvetrain clearances are at normal thermal expansion.
Battery Fully Charged ( >= 12.6 V ): Verify open-circuit battery voltage and connect a shop battery charger/maintainer. If cranking speed slows down from 220 RPM on Cylinder 1 to 140 RPM on Cylinder 8, later cylinders will read falsely low.
Disable Fuel Injection and Ignition Systems: Pull the fuel pump/injector relay or fuse (and relieve rail pressure) and disconnect primary power to the ignition coils. Why: Unburned fuel sprayed during cranking washes the lubricating oil film off the cylinder walls—artificially lowering ring sealing and compression readings—and dumps raw fuel into the exhaust catalyst.
Remove All Spark Plugs: Label each plug by cylinder number for visual inspection. Removing all plugs eliminates compression drag from the other cylinders so the starter cranks at maximum, uniform RPM.
Secure the Throttle Plate Wide Open (WOT): The cylinders cannot compress air they cannot inhale. On Electronic Throttle Control (ETC / drive-by-wire) medium/heavy-duty trucks, pressing the accelerator pedal to the floor with the key on often does not command the throttle plate to 100% WOT (unless the PCM's clear-flood mode explicitly opens the blade fully during cranking). Always remove the air intake boot to visually verify the throttle plate is open, use a scan tool bidirectional throttle-open routine, or use the manufacturer's approved mechanical test procedure; never force or wedge an electronic throttle blade.
First-Puff vs. Final-Puff (4–6 Strokes) Analysis
Thread the compression gauge tightly into the spark plug port and crank the engine through 4 to 6 compression strokes (counting each upward surge of the gauge needle), recording both the 1st puff and the final stabilized puff .
Compression Test Signature 1st Puff Reading Final Puff (Stroke 4–5) Wet Test Result (+a small manufacturer-specified quantity SAE 30 Oil) Mechanical Diagnosis
Healthy Cylinder 85–105 psi ( 50%–65% of max) 155–190 psi (within 15%–20% of highest bore) Minimal change ( +5 to +10 psi ) Normal piston ring, cylinder wall, valve, and gasket sealing
Worn Piston Rings / Bore Taper Very low ( 20–35 psi ) Slowly pumps up to 115–130 psi Jumps significantly ( +30 to +55 psi ) to 155–175 psi Worn/broken piston rings or tapered/scored cylinder wall
Burned / Sticking Valve or Broken Spring 0–40 psi Remains very low ( 0–45 psi ); does not build No significant change ( 0–50 psi ) Burned/tuliped valve, broken valve spring, bent pushrod, or tight valve lash
Blown Head Gasket Between Adjacent Bores 35–45 psi in two side-by-side bores Both adjacent bores stabilize low ( 70–75 psi ) No change in either adjacent cylinder Breached head gasket fire ring between the two adjacent cylinders
Excessive Carbon / Advanced Cam Timing 125–140 psi Abnormally high across all bores ( 225–245 psi ) Not applicable Heavy carbon deposits reducing chamber volume or jumped timing advancing intake closing
Minimum Specification & The 75%–80% Variance Rule
Aside from meeting the OEM minimum pressure specification (typically 130–150 psi minimum on modern gasoline truck V8s), the lowest-reading cylinder must be at least 75% to 80% of the highest-reading cylinder (a maximum reduction of 20% to 25% from the highest cylinder , respectively; do not equate percentage difference to a fixed psi difference).
Performing the Wet Compression Test Safely
When a cylinder reads below specification on the dry test, squirt approximately a metered amount ( a small manufacturer-specified quantity , or 3–4 pump squirts) of clean SAE 30 engine oil into the spark plug hole, rotate by hand as prescribed to distribute the oil and check that no liquid lock occurs before starter cranking, and repeat the compression test:
Pressure rises by +30 to +50 psi : The heavy oil film temporarily seals the gap between the piston rings and cylinder wall, supporting worn piston rings or cylinder bore wear .
Pressure changes by < 5–10 psi : Oil at the piston ring belt cannot seal the top of the chamber, supporting leakage past an intake valve, exhaust valve, or cylinder head gasket .
Caution
Recessed-Crown Piston Wet-Test Trap: Many heavy-duty truck gasoline engines use dished or recessed-crown pistons to control compression ratio and swirl under high load. Never pour excessive oil ( 30+ mL ) into a cylinder with a recessed piston crown: the liquid oil pools inside the piston dish, physically reduces the combustion chamber clearance volume, and artificially raises the compression ratio—producing a false high compression jump even when the real problem is a burned valve!
Running (Dynamic) Compression Testing (ASE T1 Task A.8)
A running compression test (also called a dynamic compression test) is performed with the engine idling at operating temperature by threading the compression gauge into one cylinder at a time:
Curb Idle Reading (Schrader Relief Valve Depressed): Use a gauge or pressure transducer approved for running-compression testing and follow its capture/reset procedure. Disable fuel and ignition to the tested cylinder, protect against hot gas and moving parts, and retain a secure hose connection. Because manifold vacuum restricts the incoming air mass at closed throttle, normal running compression at curb idle is 60 to 90 psi .
Snap-WOT Dynamic Peak: Quickly snap the throttle to Wide Open Throttle ( 2,000–2,500 RPM ) and release. A healthy cylinder's running WOT peak reaches approximately 80% of its cranking compression (e.g., 130 to 145 psi on an engine with 170 psi cranking compression).
Catching a Worn Camshaft Lobe: At slow starter cranking speeds ( ~200 RPM ), even a severely worn, rounded camshaft lobe that opens the intake valve only 0.080 in. instead of 0.450 in. allows enough time for atmospheric air to trickle into the cylinder and produce a normal dry cranking compression reading ( 165 psi ) . At running speeds ( 1,500–2,500 RPM ), the piston descends so fast that the barely-opening intake valve starves the cylinder of air, causing running compression to stay abnormally low ( 35–45 psi on WOT snap) and pinpointing reduced valve lift.
Worked Example: 8-Cylinder Compression Chart & Diagnosis
A fleet technician tests a 6.6L V8 medium-duty truck engine with a dead misfire on Bank 1 (Cylinders 1, 3, 5, 7 on Left Bank; 2, 4, 6, 8 on Right Bank):
Dry Cranking Finals: Cyl 1 = 180 psi , Cyl 2 = 175 psi , Cyl 3 = 72 psi , Cyl 4 = 178 psi , Cyl 5 = 75 psi , Cyl 6 = 172 psi , Cyl 7 = 176 psi , Cyl 8 = 174 psi .
Minimum Spec Calculation: Highest cylinder is Cyl 1 ( 180 psi ). Using the 80% rule ( 180 psi × 0.80 = 144 psi ), any cylinder below 144 psi fails.
Wet Test on Cyl 3 & Cyl 5: Adding a small manufacturer-specified quantity of SAE 30 oil yields Cyl 3 = 74 psi and Cyl 5 = 76 psi .
Diagnosis: Cylinders 3 and 5 are physically adjacent on Bank 1, read nearly identical low pressures ( 72 and 75 psi ), and do not improve with oil—suggesting a shared sealing fault; confirm communication between the cylinders with leak-down testing before removing the head.