Study guide
8.2 Ignition DTCs and Misfire Data
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
8.2 Ignition DTCs and Misfire Data
Key Takeaways Explain This Topic AI
P030x identifies a misfiring cylinder or pattern, not a guaranteed ignition-coil failure.
Coil letters and circuit/feedback detection logic depend on the vehicle.
Mode $06 IDs, scaling and misfire windows must be interpreted using the applicable data definition.
Last updated: October 2026
Note
Ignition DTCs and Misfire Data uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
Interpreting Ignition Diagnostic Trouble Codes (DTCs) & Mode $06 Data (Task E.2)
Diagnostic Code / Data Parameter Monitoring Method & Trigger Logic Primary Root Causes & Diagnostic Direction
P0300 (Random/Multiple Cylinder Misfire) CKP angular velocity drop detected randomly across multiple cylinders Shared system fault: low fuel rail pressure, contaminated fuel, intake plenum vacuum leak, dirty MAF sensor, stuck-open EGR valve, restricted exhaust backpressure, or unlearned/damaged CKP reluctor ring
P0301–P0310 (Cylinder 1–10 Specific Misfire) CKP angular velocity drop isolated consistently to one specific cylinder's power stroke Single-cylinder fault: defective COP coil, carbon-tracked boot/plug, fouled/wide-gap spark plug, clogged/open fuel injector, or low mechanical compression/valvetrain failure on that cylinder
P0351–P0360 (Ignition Coil A – J Primary/Secondary Circuit) PCM monitors primary current feedback, IGT trigger circuit continuity, or IGF confirmation return signal A coil circuit or feedback fault as defined by the OEM on the primary side of the specified coil (coil letters must be mapped to cylinders using service information): unplugged coil connector, broken/shorted IGT or IGF wire, open B+ feed/ground, internal coil primary/igniter failure, or bad PCM driver. Do not assume the code identifies a plug, coil or PCM without the applicable circuit test.
OBD-II Service Mode \$06 Raw current driving cycle misfire counter & Exponentially Weighted Moving Average (EWMA) per cylinder Can help localize an intermittent misfire below the code-setting threshold; verify supported monitor/test IDs, scaling, counting period and enable criteria before interpreting a result
Differentiating P030x Combustion Misfires from P035x Primary Circuit Codes
The PCM detects P0300 through P0310 by timing the passage of crankshaft reluctor teeth via the CKP sensor. Every time a cylinder fires properly, the power stroke accelerates the crankshaft slightly; when a cylinder misfires, the crankshaft momentarily slows down. A catalyst-damaging misfire can trigger a flashing MIL, while an emissions-threshold misfire follows the applicable fault-maturation strategy. The acceptable misfire rate, counting window, enabling conditions and lamp response are calibration-specific. A flashing MIL calls for reducing load and following the vehicle safety instructions; do not continue a severe misfire solely to collect more counts.
By contrast, P0351 through P0360 identify the monitored coil circuit designated A through J . Read the manufacturer's definition and any subcode to determine what was actually detected. The letter is a circuit designation; it must be mapped to the installed engine rather than assumed to match a cylinder number. A two-wire coil switched by an external driver and a smart coil with an internal driver require different tests. Some designs use an ignition trigger ( IGT ) and a separate ignition confirmation ( IGF ) signal; other designs lack that confirmation circuit. Pin count alone does not establish the switching arrangement, trigger voltage or current limit. Check the schematic, expected waveform and loaded power/ground paths before condemning the coil or controller. Injector shutoff may protect the catalyst on a supported strategy, but it is not guaranteed by the generic code label.
Tip
Using Mode \$06 for Under-Threshold Grade-Climbing Misfires: When a driver reports a transient stumble while cresting a highway grade with a loaded truck, the misfire often stops as soon as the road levels out—before the PCM accumulates enough misfire events in a 200- or 1,000-revolution window to log a pending P030x code. Open OBD-II Service Mode \$06 and select the supported cylinder misfire results using the vehicle and scan-tool definitions. An exponentially weighted moving average (EWMA) retains weighted history; it is different from a current-cycle counter. A high result suggests where to investigate, but does not establish an ignition root cause without checking fuel delivery, mechanical sealing and crankshaft-signal integrity. A zero result after reset or monitor disablement does not prove that the complaint is absent.
Worked Example: Diagnostic Scenario: High-Load V10 Grade-Climb Misfire Without Active DTCs
In this fictional service example, a Class 6 stake truck ( 26,000 lb GVWR ) with a V10 gasoline engine bucks while climbing a 6% grade at 2,100 RPM , but runs smoothly in the shop with zero active or pending DTCs . The supplied vehicle/tool definitions map cylinder misfire results to Monitor IDs \$A2 through \$AB , identify \$A8 as Cylinder 7, and specify a 0.054 in. plug gap. These are example inputs, not a claim that every V10 uses those IDs or that this is a published Triton service specification:
Mode \$06 Data Inspection: Cylinders 1–6 and 8–10 show 0 current-cycle misfires and an EWMA count of 0–1 . Monitor ID \$A8 (Cylinder #7) displays 48 current-cycle misfires and an EWMA count of 19 .
Physical Secondary Inspection: The technician removes the COP assembly from Cylinder #7. Inside the lower silicone boot is a pinhole burn mark and chalky white corona residue; removing the Cylinder #7 spark plug reveals a 0.072 in. worn electrode gap (spec 0.054 in. ) and a thin black carbon track running down the white porcelain insulator.
Root Cause & Repair: The worn gap and carbon track support secondary insulation breakdown under increased cylinder pressure; a misfire counter alone cannot establish a particular firing voltage. The technician confirms the leakage with the approved ignition test, replaces the damaged plug and boot, and follows the specified plug torque and boot-lubrication procedure. After checking normal contribution, the technician safely verifies the repair under representative conditions and confirms that the enabled current-cycle monitor records 0 new misfires . The historical EWMA need not immediately return to zero.
Source Check — October 14, 2026
Ford's published 2024–2025 OBD summary provides examples of calibrated misfire thresholds, monitor IDs and enabling conditions; these are not universal T1 limits. Manufacturer or regulator reference .
Applied Diagnostic Check
Separate current misfire evidence from learned crankshaft errors. An irregular target signal or incomplete required profile learning can disturb the monitor even when combustion feels smooth. Inspect the correlation, relevant profile status and supported diagnostic procedure before treating every counter increment as a failed plug. Conversely, a real intermittent misfire may be below the threshold that matures a code. Capture it under the driver-reported conditions and compare the suspect cylinder's waveform or contribution. The presence or absence of a code changes the available evidence, but it does not make a physical ignition fault impossible.
Checking Code Definitions and Monitor Evidence
Retrieve the complete code, its status and any failure record before clearing it. A generic code label can be less specific than the OEM diagnostic definition, especially when feedback or a subcode is present. Confirm how the coil letter maps to a cylinder and which connector pins carry power, control, ground or confirmation. Some coils have no separate confirmation wire. Do not apply an IGT/IGF test to a circuit that lacks those signals.
Interpret monitor results using their scaling and recorded conditions. A stored count can belong to a previous drive rather than the present idle. Compare a new capture under the complaint conditions with the earlier record, and account for cleared counters or an incomplete profile learn. After correcting the verified fault, check both cylinder contribution and the coil circuit result; clearing P030x does not by itself prove the underlying circuit repair is complete.