Study guide
8.5 CKP/CMP Sensor and Correlation Tests
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
8.5 CKP/CMP Sensor and Correlation Tests
Key Takeaways Explain This Topic AI
A passive VR sensor produces an AC signal whose amplitude depends on speed and air gap.
A powered Hall-type signal normally switches between its defined voltage levels.
CKP/CMP correlation must be compared with a known-good engine waveform and phaser state.
Last updated: October 2026
Note
Sensor waveforms, coil resistance and programming-supply readings in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.
8.3 Ignition Sensors (CKP/CMP), Control Modules (ICM/PCM) & Reprogramming
Distributorless and Coil-on-Plug (COP) ignition systems on medium- and heavy-duty gasoline and LPG trucks rely completely on high-resolution Crankshaft Position (CKP) and Camshaft Position (CMP) signals to calculate engine speed, piston position, dwell duration, spark advance, and sequential firing order. Under ASE T1 Tasks E.6 and E.7 , technicians must test CKP and CMP sensors with a Digital Multimeter (DMM) and Digital Storage Oscilloscope (DSO), diagnose Ignition Control Module (ICM) and Powertrain Control Module (PCM) coil driver failures, execute Crankshaft Position Variation Relearn procedures, and perform SAE J2534 module reprogramming.
- Crankshaft Position (CKP) & Camshaft Position (CMP) Sensors (Task E.6)
- Functional Roles: CKP vs. CMP
Although CKP and CMP sensors use similar magnetic or solid-state sensing elements, they serve distinct functions in engine management:
Crankshaft Position (CKP) Sensor: Monitors a multi-tooth steel reluctor wheel (tone ring) mounted on the crankshaft or harmonic balancer ( commonly 58X / 60-2 or 36-1 teeth with a machined missing-tooth index gap). The CKP sensor is the primary input for engine RPM, exact piston Top Dead Center (TDC) position, base ignition timing calculation, and crankshaft angular-velocity misfire detection . On the example strategy, a complete loss of the CKP signal during cranking results in 0 RPM on the scan tool, no primary coil switching ( no spark ), and no fuel injector pulse ( immediate crank no-start ) .
Camshaft Position (CMP) Sensor: Monitors a target wheel on the camshaft rotating at half crankshaft speed ( 1/2 RPM ) to identify stroke phase —specifically whether Cylinder #1 is approaching TDC on the compression stroke or TDC on the exhaust stroke . The PCM uses the CMP signal to synchronize sequential fuel injection timing, COP cylinder firing order, and Variable Valve Timing (VVT) cam-phaser closed-loop position. If the CMP signal fails while the CKP sensor remains healthy ( DTC P0340 or P0341 ), most truck engines exhibit extended cranking ( 3 to 5 seconds ) while the PCM tests firing phase, then start and run in batch-fire or reduced-power limp mode.
2-Wire Variable Reluctance vs. 3-Wire Hall-Effect Sensor Testing
Sensor Characteristic 2-Wire Variable Reluctance (Magnetic Inductive) 3-Wire Hall-Effect / Magnetoresistive (Digital)
Wires & External Power 2 wires (Signal High & Signal Return/Shield); no external power supply required (self-generating) 3 wires : Regulated 5.0 V or 12.0 V Reference , Sensor Ground , and Digital Signal Output
Waveform Shape on DSO Analog AC Sine Wave (with index signature at missing-tooth gap) Digital DC Square Wave ( 0 V to 5.0 V or 0 V to 12.0 V crisp vertical edges)
Effect of Increasing Engine RPM Both signal frequency AND peak-to-peak AC voltage amplitude increase ( 0.5–1.5 V AC cranking up to 15–25+ V AC at high RPM) Signal frequency increases with RPM, while peak voltage amplitude remains constant ( 5.0 V or 12.0 V ) over its specified speed range; no repeating edges occur with a stationary target
Static DMM Testing Measure coil winding resistance unplugged ( typically 200 to 1,200 Ω at 68°F / 20°C ); check AC voltage while cranking ( >0.5 V AC ) Never ohm the internal chip; backprobe with KOEO to verify 5.0 V (or 12.0 V ) reference, <50 mV ground drop, and 0 V / 5 V signal toggling when cranking
Important
Why Inductive CKP Sensors Fail Only During Slow Cranking: Because a 2-wire Variable Reluctance (VR) sensor generates voltage proportional to the rate of magnetic flux change , its AC voltage amplitude drops sharply if cranking speed is slow, the sensor air gap ( 0.020–0.050 in. ) is too wide due to rust buildup under the mounting ear ( rust jacking ), or metallic starter/clutch debris is stuck to the magnetic tip. A 3-wire Hall-Effect sensor switches full 0–5 V amplitude even if the crankshaft is barred over slowly by hand.
Reluctor Wheel Inspection & Dual-Trace CKP/CMP Correlation ( P0016 / P0017 )
When a truck sets P0016 (Crankshaft Position – Camshaft Position Correlation Bank 1 Sensor A) or experiences high-RPM timing scatter, connect a dual-trace oscilloscope with Channel 1 on the CKP signal and Channel 2 on the CMP signal:
Bent or Chipped Reluctor Tooth: Inspect the CKP waveform across two full crankshaft revolutions ( 720° ). A single bent, cracked, or chipped tooth on the crankshaft tone ring produces a repeating low-amplitude or widened dropout once every 360° revolution, which tricks the PCM's misfire monitor into logging false P0300 codes.
Non-Invasive Timing Chain & VVT Phaser Verification: With the engine at warm curb idle and the VVT oil-control solenoid commanded to 0% (using the manufacturer's base-position test; unplugging a solenoid does not guarantee mechanical locking), count how many CKP tooth pulses occur between the CKP missing-tooth sync gap and the rising edge of the CMP square wave. Comparing this tooth count against an OEM known-good waveform overlay supports whether the timing chain has jumped/stretched or a VVT phaser is mechanically stuck— before spending hours removing the front timing cover !
Applied Diagnostic Check
When a correlation trace changes with temperature, compare the same requested phaser state and oil conditions. A hydraulic control that has not reached its target can shift the cam signal without a jumped chain. Inspect sensor mounting and target integrity as separate candidates. A damaged tooth can alter one part of the waveform while the rest looks regular. Capture enough revolutions to distinguish a repeating target event from electrical noise. Mark the known-good reference and actual engine application; a waveform from a different reluctor design cannot supply an exact tooth-count standard for this engine.
Avoiding a Misleading Sensor Identification
Wire count is a clue, not a technology specification. Some active sensors use two-wire current signaling, while a passive magnetic sensor can include a shield in addition to its signal conductors. Read the circuit description and expected waveform before applying resistance testing or an external source. A powered sensor needs the specified supply and return; a missing waveform can result from either of those paths.
Check the target wheel, mounting gap and connector as well as the sensor. Capture a sufficient time window to compare indexed crank and cam events. A phaser that has not reached the specified test position can make a sound mechanical timing set appear incorrectly indexed. Record the test state and known-good reference before judging correlation.