Study guide

8.4 Spark Plugs and Secondary Waveforms

ASE T1 — Gasoline Engines Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Introduction & ASE T1 Exam Overview

1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy

2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust

2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds

3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing

3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing

4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools

4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service

5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair

5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service

6 Chapter 5: Engine Block Diagnosis and Repair

6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection

7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair

7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators

8 Chapter 7: Ignition System Diagnosis and Repair

8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning

9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair

9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service

10 Chapter 9: Emissions Control Systems Diagnosis and Repair

10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures

11 Chapter 10: Computerized Engine Controls Diagnosis and Repair

11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation

8.4 Spark Plugs and Secondary Waveforms

Key Takeaways Explain This Topic AI

A colder plug transfers heat away faster; use the specified heat range.

Carbon tracking can remain in both the plug and boot and requires complete inspection.

An oscillation count alone does not prove that a coil is either healthy or shorted.

Last updated: October 2026

Note

Spark Plugs and Secondary Waveforms uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.

  • Spark Plugs, Heat Range Physics, Deposit Analysis & Secondary Wires (Task E.4)
  • Spark Plug Heat Range & Heavy-Duty Truck Selection

A spark plug's heat range describes how fast it conducts combustion heat away from its firing tip into the cylinder head cooling jacket—it does not alter spark voltage or intensity . Heat transfer rate depends partly on the length and surface area of the ceramic insulator nose before it contacts the metal shell and seat:

Cold Spark Plug (Short Insulator Nose): Features a short ceramic nose and deep metal shell contact that provides a short, rapid heat-transfer path into the water-cooled cylinder head. Cold plugs keep the insulator tip below the pre-ignition limit ( ~850°C / 1,560°F ) and may be specified for engines operating at sustained high GVWR, stationary high-RPM PTO applications, and dry-fuel LPG (propane) engines.

Hot Spark Plug (Long Insulator Nose): Features a longer exposed ceramic nose that transfers heat more slowly into the cylinder head, keeping tip temperature above the self-cleaning carbon burn-off threshold ( ~450°C / 840°F ) during light-duty urban stop-and-go idling.

Reading Spark Plug Deposits, Carbon Tracking & Wire Service

Inspecting removed spark plugs reveals the exact combustion environment inside each cylinder:

Normal Condition: Light tan or grayish-brown insulator nose with crisp electrode edges.

Dry, Fluffy Black Carbon Deposits: Caused by an overly rich air-fuel mixture (leaking injector, excessive fuel pressure, restricted air filter), weak ignition output, prolonged cold idling, or a spark plug heat range that is too cold .

Wet, Oily Black Fouling: Caused by engine lubricating oil entering the chamber past worn piston oil-control rings, scored/glazed cylinder walls, or worn valve stem seals and guides.

Hard, Crusty Light-Brown or White Ash Deposits: Caused by oil additives or fuel treatment chemicals burning in the combustion chamber and encrusting the electrodes.

Blistered Chalky-White Insulator & Melted/Rounded Electrodes: Caused by extreme combustion chamber heat from a lean air-fuel mixture, over-advanced ignition timing, cooling system failure, sustained detonation/pre-ignition, or a spark plug heat range that is too hot .

Carbon Tracking (External Black Lightning Streak): A thin, dark pencil-like vertical line burned down the white ceramic ribs of the plug insulator supports high-voltage flashover inside a degraded COP rubber boot. Always replace both the carbon-tracked spark plug and the rubber COP boot together —installing a new spark plug inside an old carbon-tracked boot will immediately burn a carbon track into the new plug! Coat the inside of the new silicone boot with silicone dielectric grease to seal out moisture, prevent corona/voltage leakage, and keep the boot from vulcanizing to the porcelain (never smear dielectric grease directly onto metal primary pins).

When servicing fine-wire iridium or platinum spark plugs , use a wire-loop gauge carefully so you never pry against the brittle 0.6 mm center iridium tip. Always torque spark plugs to OEM specification ( typically 11–25 lb-ft on aluminum heads) to ensure proper heat transfer through the tapered seat or crush gasket and to prevent thread blowout. On Coil-Near-Plug (CNP) or distributorless systems with carbon-core TVRS (Television-Radio Suppression) secondary wires, measure resistance on a DMM while flexing the lead; normal resistance is 3,000 to 10,000 Ω per foot ( 3–10 kΩ/ft ) .

Secondary Ignition Oscilloscope Waveform Diagnosis (Task E.5)

Scope Section / Waveform Feature Normal Warm Idle Specification Abnormal Waveform Signature Confirmed Root Cause

Firing Line (Ionization Peak) 8 to 14 kV ( max 3–4 kV variation between cylinders) Abnormally High ( 18–25+ kV ) + Short Burn Time ( <0.7 ms ) Excessive secondary resistance: open/burned plug wire, wide spark plug gap, lean mixture, or high compression

Firing Line (Ionization Peak) 8 to 14 kV Abnormally Low ( <4–5 kV ) + Short/Missing or Sloping Burn Line Secondary leak/short or low pressure: carbon-tracked boot/plug, fouled plug, narrow gap, or low cylinder compression

Spark Line & Burn Duration 1.5 to 3.0 kV plateau lasting 1.2 to 2.2 ms Steep Upward Slope / Heavy Hash with <0.8 ms burn duration Lean air-fuel mixture, high combustion turbulence, or high resistance in secondary circuit

Coil Ring-Down Oscillations 4 to 8 damped oscillations immediately after spark extinguishes Zero or only 1–2 oscillations after spark blowout Possible coil or circuit damping fault; compare a known-good waveform and verify supply, dwell and secondary load

Primary Current Ramp (Low-Amp Clamp) Smooth calibrated ramp to 6–12 A in 2.0–3.5 ms with turn-on hook Vertical spike ( >12 A in <0.5 ms ) with no turn-on inductive hook Shorted primary coil winding (risk of burning out PCM/ICM transistor driver)

Tip

Why Firing Line Height and Spark Burn Duration Move in Opposite Directions: Each ignition coil stores a finite packet of magnetic energy ( millijoules ) during dwell. If an open plug wire or wide spark plug gap requires 23 kV to jump the gap instead of 10 kV , most of the coil's stored energy is consumed just initiating the arc—leaving very little energy to sustain the spark line, which shrinks burn duration below 0.6–0.7 ms .

Worked Example: Diagnostic Scenario: Secondary Scope Parade & Ring-Down Analysis

A Class 5 utility truck with a 6.0L V8 Coil-Near-Plug (CNP) engine exhibits a rough idle and hesitation under throttle. Using a DSO with a capacitive COP/CNP pickup probe, the technician captures a secondary ignition parade waveform at warm idle:

Cylinders 1–4 and 6–8: Display uniform 10 to 12 kV firing lines , flat 1.8 kV spark lines lasting 1.6 ms , and 6 crisp ring-down oscillations after spark blowout.

Cylinder #5: Displays a 23.5 kV firing line , an upward-sloping spark line lasting only 0.55 ms , followed by 5 clean ring-down oscillations .

Diagnosis & Repair: Because Cylinder #5 still exhibits 5 strong ring-down oscillations after spark blowout, ring-down alone does not condemn Coil #5 . The high 23.5 kV firing line combined with the short 0.55 ms burn duration supports excessive secondary resistance downstream of the coil . Measuring the Cylinder #5 short CNP plug wire with a DMM reveals an internal break reading 64,000 Ω (spec 3,500 Ω ), and the spark plug gap is worn to 0.080 in. . Replacing the plug wire and spark plug restores Cylinder #5's firing line to 11 kV and burn time to 1.6 ms .

Source Check — October 13, 2026

NGK explains plug heat range and insulator-nose heat transfer; select the specified plug for the application. Manufacturer or regulator reference .

Loading diagram... Primary Current Ramping & Secondary Ignition Oscilloscope Waveform Analysis