Study guide
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements
Key Takeaways Explain This Topic AI
T1 has 50 scored and 10 unidentified research questions; T1R has 25 questions and 30 minutes.
A single T1 order costs $96 before applicable tax: $34 registration plus $62 test fee.
ASE evaluates a two-year experience requirement and program-specific training credits.
Master Medium/Heavy Truck status requires active T2–T8 certifications; T1 is not required.
Last updated: October 2026
The National Institute for Automotive Service Excellence (ASE) Medium/Heavy Truck Test T1: Gasoline Engines evaluates gasoline-engine diagnosis, service and repair within the T-Series program for Class 4 through Class 8 trucks and tractors . Its official task list combines mechanical engine repair with ignition, fuel delivery, air induction, emissions control and computerized engine management. The breadth matters: a misfire can originate in valve sealing, a loaded ignition circuit, injector delivery or a control input, so preparation must connect mechanical measurements with electrical and scan-data evidence. T1 is distinct from the Automobile A1 credential and the Medium/Heavy Truck T2 Diesel Engines credential. This guide follows the current 98 numbered T1 tasks across eight content areas . It also includes clearly identified LPG fleet-service examples as supplementary instruction; those examples do not establish an additional ASE fuel-system endorsement or replace the published T1 task list.
Official 2026 ASE T1 and T1R Exam Specifications
When registering for the T1 credential, technicians must distinguish between the full initial certification examination ( T1 ) and the shorter recertification examination ( T1R ) taken every five years to keep an active credential current. Every initial T1 examination contains 60 total multiple-choice questions administered within a 75-minute (1 hour 15 minute) seat-time limit. Of those 60 items, 50 questions are scored toward your pass/fail determination, and 10 questions are unscored research questions used by ASE psychometricians to evaluate statistical item performance for future test forms. Because unscored research questions are distributed randomly throughout the test and cannot be identified by the candidate, you must answer all 60 questions with equal care, maintaining an average pacing of 75 seconds per question ( 75 minutes ÷ 60 questions ).
- Exam Parameter Initial Certification ( T1 ) Recertification ( T1R )
- Total Administered Questions 60 multiple-choice questions 25 multiple-choice questions
- Scored Questions 50 scored questions 25 scored questions
- Unscored Research Questions 10 unscored questions (unidentified) 0 unscored questions
- Time Limit 75 minutes (1 hour 15 minutes) 30 minutes
- Average Pacing per Question 75 seconds ( 1.25 minutes ) 72 seconds ( 1.20 minutes )
- Official Task List Scope 98 tasks across 8 content areas 98 tasks across 8 content areas
- Credential Validity Period 5 years upon experience verification 5 years from renewal date
- The Eight Official ASE T1 Content Areas
Unlike the Automobile A1 exam—which restricts its scope primarily to internal mechanical repair while deferring deep ignition, fuel, and electronic diagnostics to A6 and A8—the Medium/Heavy Truck T1 exam tests the entire spark-ignited engine system from mechanical base-engine hardware to onboard diagnostics (OBD) and emissions controls. Across the 50 scored questions , ASE distributes items across eight functional content areas covering 98 official tasks :
- Content Area Official Domain Title Scored Questions Exam Weight Official Tasks
- Area A General Engine Diagnosis 14 28% 20 tasks (A.1–A.20)
- Area B Cylinder Head and Valve Train Diagnosis and Repair 4 8% 8 tasks (B.1–B.8)
- Area C Engine Block Diagnosis and Repair 4 8% 15 tasks (C.1–C.15)
- Area D Lubrication and Cooling Systems Diagnosis and Repair 3 6% 12 tasks (D.1–D.12)
- Area E Ignition System Diagnosis and Repair 6 12% 7 tasks (E.1–E.7)
- Area F Fuel, Air Induction, and Exhaust Systems Diagnosis and Repair 6 12% 13 tasks (F.1–F.13)
- Area G Emissions Control Systems Diagnosis and Repair 5 10% 12 tasks (G.1–G.12)
- Area H Computerized Engine Controls Diagnosis and Repair 8 16% 11 tasks (H.1–H.11)
- Total All ASE T1 Scored Content Areas 50 100% 98 tasks
Notice how the exam weights diagnostic proficiency: Area A (General Engine Diagnosis, 28%) and Area H (Computerized Engine Controls, 16%) together account for 44% of your entire score (22 of 50 scored questions). Meanwhile, Area E (Ignition, 12%) , Area F (Fuel, Air Induction, and Exhaust, 12%) , and Area G (Emissions Control, 10%) add another 34% (17 questions). Together, system-level driveability, ignition, fuel, emissions, and electronic controls represent 78% of the scored exam , whereas internal mechanical teardown and machining across Areas B, C, and D account for 22% (11 questions).
Important
Remote Testing & Renewal App Restrictions for T-Series: Initial certification for ASE T1 must be completed in person at an authorized Prometric test center . Prometric ProProctor remote online testing is available only for recertification exams (such as T1R ) —never for an initial T1 certification attempt. Furthermore, the ASE Renewal App ($52 annual subscription) is restricted exclusively to Automobile ( A1–A9 ) credentials and does not cover Medium/Heavy Truck ( T1–T8 ) certifications.
2026 Official Fees, Order Caps, and Language Support
Under the 2026 ASE fee schedule, every purchase transaction includes a flat $34 registration fee per order (charged once per checkout regardless of how many tests are purchased in that transaction) plus a $62 test fee for each individual T-series test:
Single Initial T1 Exam Order: Purchasing the T1 exam by itself costs $96 total ( \$34 registration fee + \$62 test fee ).
Bundled Multi-Test Order: Purchasing two T-series exams in a single order (for example, T1 and T6) costs $158 total ( \$34 registration fee + [2 × \$62 test fees] ), saving an extra $34 registration fee compared to placing two separate orders.
Recertification Fee Cap ( T1R ): For recertification exams, individual test fees are $62 each, but ASE caps total recertification test fees at $186 per order once 3 or more recertification tests are purchased in the same transaction ( 3 × \$62 = \$186 ). Including the $34 registration fee, your maximum total order cost for recertification is $220 per transaction, even if you bundle four to eight recertification tests together.
All ASE computer-based exams provide a built-in English-to-Spanish pop-up glossary of technical terms that any candidate can open on screen during the test. However, full split-screen Spanish translation is limited to the Automobile ( A1–A9 ) and G1 exams and is not available on Medium/Heavy Truck ( T1–T8 ) exams.
Scheduling Windows, Cancellations, Retakes, and Master Truck Status
Strict administrative rules govern exam scheduling, rescheduling, retakes, and credential issuance:
90-Day Eligibility Window: Candidates have 90 calendar days from the date of purchase to schedule and take the exam at a Prometric test center.
3-Day Reschedule and Cancellation Cutoff: Appointments cannot be rescheduled or canceled within 3 days of the scheduled test date.
30-Day Retake Waiting Period: After receiving either a Pass or Fail result, candidates must observe a mandatory 30-day waiting period (30 full calendar days) before repurchasing and retesting the same exam.
2-Year Work Experience Requirement: Earning official ASE T1 certification requires 2 years of relevant hands-on work experience in automotive or medium/heavy truck repair. ASE-approved formal training may substitute for part of the requirement. The current ASE table grants 1 year for completing an ASE-accredited program or passing three different Entry-Level tests, up to 1 year for other training at two months or 200 program hours per month of credit, and 2 years for a completed ASE-accredited OEM-sponsored co-op program, including its hands-on portion. These alternatives cannot be combined. Passing the T1 exam before fulfilling the experience requirement earns an official test score report, not certification, until experience verification is completed. Once issued, certification is valid for 5 years .
Tip
Why ASE T1 Is Not Required for Master Medium/Heavy Truck Technician Status: Achieving Master Medium/Heavy Truck Technician status requires active certification in T2 through T8 (T2 Diesel Engines, T3 Drive Train, T4 Brakes, T5 Suspension and Steering, T6 Electrical/Electronic Systems, T7 Heating, Ventilation, and Air Conditioning, and T8 Preventive Maintenance Inspection). T1 is NOT required for Master Medium/Heavy Truck Technician status as stated in ASE's T-series requirements. T1 serves technicians who support commercial spark-ignited engines.
- Official Sources Checked October 13, 2026
- ASE T-series scope and certification requirements
- 2026 owner task list and test specifications
- Registration, fees and scheduling
- Detailed experience and training credits
- T1R remote testing
ASE reports pass/fail and content-area performance. Its public T1 specifications do not publish a fixed passing percentage or a guaranteed number of correct responses; do not invent either.