Study guide

7.4 Coolant Testing and Water Pump Service

ASE T1 — Gasoline Engines Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Introduction & ASE T1 Exam Overview

1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy

2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust

2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds

3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing

3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing

4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools

4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service

5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair

5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service

6 Chapter 5: Engine Block Diagnosis and Repair

6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection

7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair

7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators

8 Chapter 7: Ignition System Diagnosis and Repair

8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning

9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair

9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service

10 Chapter 9: Emissions Control Systems Diagnosis and Repair

10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures

11 Chapter 10: Computerized Engine Controls Diagnosis and Repair

11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation

7.4 Coolant Testing and Water Pump Service

Key Takeaways Explain This Topic AI

Coolant color is not an approval or chemistry specification.

A refractometer must be calibrated for the coolant type and supplier chart.

Coolant-probe voltage alone cannot identify a failed ground strap or prove stray-current corrosion.

Last updated: October 2026

Note

Coolant Testing and Water Pump Service uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.

Coolant Chemistry, Refractometer Testing, Electrolysis & Vacuum Bleeding (Task D.8)

Commercial fleets operate three primary ethylene glycol coolant families: IAT (conventional green silicate/phosphate), OAT (silicate-free Organic Acid Technology such as orange Dex-Cool or heavy-duty extended-life red/pink carboxylate coolants), and HOAT (Hybrid OAT combining organic acids with low silicate or nitrite additives, typically yellow, gold, or turquoise). Never mix incompatible coolant chemistries : mixing products without verifying compatibility can dilute inhibitor performance or create deposits; gel formation is not an inevitable result of every IAT/OAT mixture that plugs radiator tubes, heater cores, and oil coolers while stripping corrosion protection.

Coolant Test Parameter Test Instrument & Method Normal / Target Specification Fault Reading & Diagnostic Consequence

Standard Freeze/Boil Concentration Optical refractometer (temperature-compensated drop test) 50% glycol / 50% distilled water ( -34°F / -37°C freeze point; 226°F boil at 0 psi , use the coolant supplier's pressure/boiling chart, such as 265°F at 15 psi for the cited Prestone product) <40% glycol risks freezing, boil-over, and water pump cavitation

Maximum Arctic Concentration Optical refractometer 60%–65% glycol / 40%–35% water ( -62°F / -52°C max freeze protection) >68%–70% glycol reverses freeze point ( 100% glycol freezes at +8°F !) and cuts heat transfer

Coolant Acidity / Alkalinity ( pH ) Digital pH meter or calibrated coolant pH test strips pH 7.5 to 10.5 ( typically 8.0–9.5 for inhibited ethylene glycol) pH < 7.0 (acidic) corrodes iron/aluminum; pH > 11.0 dissolves aluminum oxide film

Galvanic & Stray-Current Electrolysis DMM set to DC Volts: black lead on (-) battery post, red probe submerged in coolant (not touching metal) <0.15 V DC ( 150 mV ) normal; 0.30 V DC ( 300 mV ) absolute max >0.30–0.40 V DC eats pinholes through aluminum radiator and heater cores within weeks

Venturi Vacuum Cooling System Refill Shop-air Venturi vacuum refiller attached to radiator/degas neck Pulls 24–26 in. Hg ( 80–88 kPa ) vacuum ; must hold steady for 2–5 mins Eliminates air locks in tall cab heaters and elevated LPG vaporizers/regulators

Important

Distinguishing Stray-Current Electrolysis from Galvanic Corrosion: When a truck repeatedly blows pinhole leaks in aluminum heater cores or radiators, perform a DMM coolant voltage test with the black probe on the negative battery post and the red probe tip dipped directly into the liquid coolant (avoiding metal contact). Observe the reading with the key off, while cranking, and at 1,500 RPM with high-amperage loads (headlamps, blower motor on high, A/C clutch, liftgate/PTO solenoids) switched ON. If voltage jumps above 0.30 V DC only when electrical loads are energized, a ground fault is a candidate; confirm the relevant ground voltage drops and repeat the test under the OEM procedure before attributing corrosion to stray current ( stray-current electrolysis ). If >0.30 V DC persists even with the negative battery cable disconnected, a galvanic reading is possible; a probe in coolant can itself create an electrochemical voltage, so this reading alone does not diagnose coolant condition ( galvanic corrosion ).

Always mix concentrated coolant with distilled or deionized water (never tap water rich in calcium and chlorides that form insulating hard-water scale on hot cylinder head walls). After flushing, use a Venturi vacuum cooling system refiller ( 24–26 in. Hg ) to eliminate trapped air pockets—especially critical on commercial trucks with roof/rear auxiliary heaters or elevated LPG liquid-to-vapor converters , where an air pocket will freeze the LPG regulator solid with frost while the engine overheats!

Water Pump, Housing & Hose Inspection and Replacement (Task D.9)

Centrifugal water pumps circulate thousands of gallons per hour through the block and heads:

Shaft Bearing and Weep Hole Inspection: With the belt removed, rock the water pump pulley to check for radial bearing play and spin by hand to feel for roughness. Inspect the weep (vent) hole underneath the pump nose housing: a light, dry chalky residue or minor evaporation stain around the weep hole is normal from initial ceramic-carbon mechanical face-seal seating and does not warrant replacement. However, active liquid coolant dripping or wet streaks running down the front cover confirm seal failure and require water pump replacement.

Impeller Cavitation and Slippage: If an engine overheats at highway speed despite a verified clean radiator and tested thermostat, remove the water pump and inspect the impeller vanes for cavitation erosion (vapor bubbles imploding on the low-pressure suction side of the vanes, eating away the blades) or a composite plastic impeller that cracks and slips on the steel shaft once hot.

Hose Electrochemical Degradation (ECD) and Lower Hose Collapse: Radiator and heater hoses deteriorate from the inside out due to Electrochemical Degradation (ECD) , where electrochemical reactions can damage the inner hose material and create micro-cracks in the inner EPDM tube near the metal hose fittings, shedding rubber particles while the outside of the hose looks intact. Squeeze hoses firmly near the ends to check for spongy softness, and verify that the lower (suction) radiator hose retains its internal support spring or rigid molded wall so water-pump suction cannot collapse it flat at high RPM.

Worked Example: Diagnostic Scenario — Highway Overheating & Repeat Heater Core Pinholes

A Class 5 commercial dump truck equipped with a 7.3L V8 gasoline engine comes into the shop with two complaints: it overheats ( 238°F ) only when hauling a heavy load up highway grades, and it has burned through two aluminum cab heater cores in four months. At idle, cooling fan engagement and cab heat are normal. Testing the coolant with an optical refractometer reveals an over-concentrated 75% ethylene glycol / 25% water mixture (somebody topped off repeatedly with 100% undiluted antifreeze, slashing specific heat capacity and raising the freeze point). A DMM electrolysis test with the blower motor and headlamps ON measures 0.54 V DC in the coolant ; inspecting the chassis reveals a broken braided ground strap between the right cylinder head and the cab firewall. Finally, revving the engine to 2,800 RPM in the bay reveals the softened lower radiator hose sucking flat under water-pump suction. Replacing the broken cab ground strap (dropping coolant voltage to 0.06 V DC ), replacing the collapsed lower radiator hose, flushing the system, and vacuum-refilling with a 50/50 mix of OEM coolant and distilled water resolves both complaints.

Loading diagram... Commercial Engine Overheating, Thermostat & Coolant Electrolysis Diagnostic Flow