Study guide

8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections

ASE T3 Drive Train Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Drive Train Fundamentals

1.1 ASE T3 Exam Format, Scoring, and Technician A/B Question Strategy 1.2 Medium/Heavy Truck Drive Train Architecture and Shop Safety

2 Clutch Construction & Actuation Systems

2.1 Push-Type vs. Pull-Type Clutches and Two-Plate Construction 2.2 Clutch Release Linkages, Hydraulic Systems, and Free Pedal Adjustment 2.3 Clutch Brake Operation, Types, Clearance, and Squeeze Adjustment 2.4 Release Bearings, Cross-Shafts, Clutch Safety Switches, Input Shaft Wear, and Clutch Torque Ratings

3 Clutch Adjustment, Maintenance & Troubleshooting

3.1 Manual vs. Self-Adjusting Clutches and Internal Adjustment Procedures 3.2 Flywheel Inspection, Resurfacing, Pilot Bearings, and Housing Alignment 3.3 Diagnosing Slip, Chatter, Drag, and AMT Clutch Actuators & Calibration

4 Manual Transmission Mechanics, Overhaul & Transfer Cases

4.1 Heavy-Duty Manual Transmission Layout: Twin Countershafts & Floating Main Shaft 4.2 Shift Bar Housings, Rails, Shift Forks, Detents, and Interlock Mechanisms 4.3 Main Box Power Flow, Sliding Clutches, and Gear Ratios 4.4 Transmission Lubrication, Cooling, Filtration, and PTO Installation & Backlash 4.5 Transmission Removal, Mounts, Leaks, and Overhaul Inspection (Shafts, Bearings, Reverse Idlers, Synchronizers, Cases) 4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles

5 Auxiliary Sections, Air Shifts, AMTs & Transmission Electronics

5.1 Auxiliary Gearing: Range and Splitter Section Design and Power Flow 5.2 Air Shift Systems: Roadranger Valves, Slave Valves, Cylinders, and Regulators 5.3 Diagnosing Gear Jump-Out, Gear Clash, Hard Shifting, and Bearing Noise by Gear 5.4 Automated Manual Transmissions (AMT): Actuators, Sensors, Diagnostics, and Calibration 5.5 Transmission Electrical Circuits: Speed Sensors, Electronic Speedometer Drives, Neutral and Reverse Switches, and Temperature Senders 5.6 Electronic Shift Controls and Diagnosis: In-Cab Selectors, Circuit Testing, Fault Codes, and J1939 Data-Link Faults

6 Driveshafts & Universal Joints

6.1 Driveline Operating Angles, Digital Inclinometers, and Torsional Angle Cancellation 6.2 Driveshaft Phasing, Spline Alignment, Runout Limits, and Dynamic Balancing 6.3 Heavy-Duty Universal Joint Types (Half-Round, Full-Round, Wing), Inspection, and Lube 6.4 Center Support Bearings, Slip Yokes, and Driveline Vibration Diagnostics (First vs. Second Order)

7 Drive Axles, Tandems, Power Dividers & Differential Locks

7.1 Drive Axle Configurations: Single-Reduction, Double-Reduction, and Tandem Through-Shaft 7.2 Interaxle Differential (Power Divider) Operation, Air Lockouts, and Spinout Prevention 7.3 Standard Differential Nest: Side Gears, Spider Cross, Pinions, and Thrust Washers 7.4 Driver-Controlled Main Differential Locks (DCDL): Operation, Operating Rules, Sensor Switch, and Service

8 Differential Setup, Axle Service, Lubrication & Wheel Ends

8.1 Carrier Setup: Pinion Depth, Bearing Preload, and Backlash Adjustment 8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections 8.3 Full-Floating Axles, Wheel Bearings, Hub Seals, and Drive vs. Coast Noise Diagnosis 8.4 Drive Axle Lubrication, Fill Procedures, Leaks, Carrier Removal, Housings, Lube Pumps, and Temperature Indicators 8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis

8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections

Key Takeaways Explain This Topic AI

Meritor's check: apply marking compound to about 12 ring gear teeth and roll them past the pinion six times, forward and backward.

On the ring gear, the convex side of the tooth is the drive side and the concave side is the coast side.

A good hand-rolled pattern on a new hypoid set is toward the toe and centered between the top and bottom of the tooth; under load it spreads to nearly full length.

Pinion depth moves the pattern up or down the tooth; on a Meritor cage carrier, a thinner cage shim pack corrects a high pattern and a thicker pack corrects a low pattern.

Backlash moves the pattern along the tooth: decrease backlash to move it toward the toe, increase it to move it toward the heel.

Last updated: September 2026

  • 8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections
  • The Primacy of Tooth-Contact Pattern Analysis

During differential carrier assembly, measuring pinion bearing rolling torque, pinion depth, and ring gear backlash with dial indicators provides essential baseline alignment. However, tooth-contact pattern diagnosis is the final and absolute authority governing gearset setup. Dial indicators and depth micrometers measure cold, static, single-point dimensions. They cannot account for microscopic variations in tooth hobbing, spiral lead curvatures, bearing seat runout, or casting flex.

Even when dial indicator measurements of backlash (e.g., 0.010 " 0.010" 0.010" ) and pinion depth fall strictly within manufacturer blueprint specifications, the tooth contact pattern can reveal severe misalignment. If a conflict arises between dimensional measurements and the tooth contact pattern, the contact pattern takes complete precedence . Technicians must adjust pinion depth shims and ring gear backlash until an optimal contact pattern is achieved. Operating a commercial carrier with an improper contact pattern under heavy line-haul or vocational torque results in rapid gear tooth pitting, edge chipping, fatigue snapping, and howling gear whine.

Hypoid Gear Tooth Anatomy and Loading Dynamics

Interpreting contact patterns requires a precise understanding of the structural anatomy of spiral bevel and hypoid gear teeth. Every ring gear tooth possesses four distinct anatomical boundaries and two functional working faces: Hypoid Ring Gear Tooth Anatomy

  • Toe (Narrow Inner End) Heel (Wide Outer End)
  • +----------------------------+
  • / Face (Crown / Top Land) /|
  • / / |
  • +----------------------------+ |
  • | | |
  • Pitch Line ---- | - - - - - - - - - - - - - -| -+
  • | | /
  • | Flank (Root / Bottom Land) |/
  • +----------------------------+
  • Root Fillet
  • [ Convex Face = Drive Side ] [ Concave Face = Coast Side ]
  • (Curves outward; loaded under (Curves inward; loaded under
  • forward engine acceleration) engine compression braking)
  • Working Faces: Drive vs. Coast

Drive Side (Convex Face) : The tooth surface that curves outward . It carries the load when the engine drives the vehicle forward. Because trucks spend most of their working life under forward drive load, the drive-side pattern matters most for gear life.

Coast Side (Concave Face) : The tooth surface that curves inward (concave profile). This face is loaded when the vehicle pushes the engine during deceleration, closed-throttle coasting, or heavy engine compression braking (Jake brake operation). In reverse gear, the coast side acts as the driving surface.

Geometric Boundaries

Toe : The narrow inner end of the gear tooth closest to the center of the differential case.

Heel : The wide outer end of the gear tooth closest to the outer perimeter of the ring gear.

Face (Crown) : The upper profile of the tooth surface located between the pitch line and the top land (tip) of the tooth.

Flank (Root) : The lower profile of the tooth surface located between the pitch line and the bottom root land (fillet) of the tooth.

Pitch Line : The imaginary longitudinal centerline along the tooth profile where mating teeth engage in pure rolling contact without relative sliding motion.

Gear Pattern Marking and Inspection Protocol

Generating an accurate, readable tooth contact pattern requires precise chemical preparation and mechanical drag simulation. Technicians must avoid shortcuts that produce smeared or unreadable patterns.

Step 1: Surface Preparation and Cleaning

Clean the ring gear teeth so the marking compound sticks. Before checking the pattern, Meritor sets backlash to 0.012 in. or 0.015 in. for a new gear set (depending on ring gear size), or to the value measured before disassembly for an old set.

Step 2: Applying Marking Compound

Meritor's procedure is to apply marking compound to approximately 12 teeth of the ring gear, on both the drive (convex) and coast (concave) sides, and rotate the ring gear so those teeth are next to the drive pinion. Use a gear marking compound that shows a clear contact impression.

Step 3: Rolling the Pattern

Rotate the ring gear forward and backward so the 12 marked teeth go past the drive pinion six times (Meritor). Repeat if you need a clearer pattern.

Light drag on the ring gear helps produce a crisp impression.

Compare the drive-side and coast-side patterns with the OEM's pattern illustrations.

The Ideal Tooth Contact Pattern

Under static bench inspection, the ideal tooth contact pattern exhibits three definitive characteristics: Ideal No-Load Tooth Contact Pattern

  • Toe (Inner End) Heel (Outer End)
  • +--------------------------------------------------+
  • | Face (Crown) |
  • | /----------------\ |
  • Pitch Line | - - - - - - | Contact Zone | - - - - - - - - - |
  • | \----------------/ |
  • | Flank (Root) |
  • +--------------------------------------------------+
  • (Centered vertically; biased slightly toward toe)

Vertical Centering (Face-to-Flank) : The contact patch is centered vertically on the tooth profile, straddling the pitch line. It does not contact the top land (crown) of the tooth, nor does it dig down into the root fillet (flank).

Longitudinal Position (Toe-to-Heel) : On a hand-rolled (no-load) check of a new hypoid gear set, Meritor's good pattern is toward the toe (inner narrow end) of the tooth. It must not run off either end.

Drive vs. Coast Balance : The pattern appears in matching vertical and longitudinal locations on both the drive (convex) and coast (concave) sides of the teeth.

The Engineering Mechanics of Dynamic Torque Deflection

Why must the static bench contact pattern be biased toward the toe?

Engine torque multiplied through the transmission and axle deflects the carrier under load:

The hypoid spiral tooth angle generates high axial separating forces that push the drive pinion shaft axially rearward .

The ring gear is forced laterally away from the pinion, flexing the differential case flange and expanding the carrier housing bearing legs.

As a result of this dynamic deflection under load, the physical contact zone on the ring gear teeth migrates outward toward the wide heel and upward toward the crown .

Meritor puts it this way: a good hand-rolled pattern for a new hypoid gear set is toward the toe and centered between the top and bottom of the tooth, and when the carrier operates, a good pattern extends approximately the full length of the tooth, with its top near the top of the tooth. If a technician centered the pattern between toe and heel on the bench, load could push it off the heel edge. Concentrating peak torque on the outer heel corner causes severe edge loading, fatigue fractures, and sheared teeth. Setting a slight toe bias under zero load ensures that when the vehicle pulls a heavy payload up a grade, elastic deflection pulls the pattern into the absolute center of the tooth , distributing mechanical stress evenly across the full width of the gear tooth.

Diagnosing Pattern Faults and Systematic Corrections

When a tooth contact pattern deviates from the ideal specification, the technician must diagnose the root cause and execute targeted mechanical adjustments. Pattern errors fall into four primary categories: High , Low , Toe , and Heel . +-------------------------------------------------------------------------+

  • | The Two-Step Golden Rule of Gear Correction |
  • +-------------------------------------------------------------------------+
  • | Rule 1: PINION DEPTH moves the pattern VERTICALLY between Face & Flank |
  • | Rule 2: BACKLASH moves the pattern HORIZONTALLY between Toe & Heel |
  • | |
  • | --> ALWAYS correct Pinion Depth FIRST to center the pattern vertically |
  • | --> THEN adjust Backlash to position the pattern lengthwise |
  • +-------------------------------------------------------------------------+
  • 1. High Pattern (Face / Crown Contact)

Visual Symptom : The contact impression is positioned high on the tooth profile, running along the top crown (face) of both drive and coast flanks.

Root Cause : The drive pinion is not installed deep enough (too far from the ring gear).

Corrective Action :

Move the pinion toward the ring gear. On a Meritor cage carrier, decrease the thickness of the shim pack under the pinion bearing cage (Meritor: "when decreasing the thickness of the shim pack, the drive pinion will move toward the ring gear"). On designs with shims behind the inner cup or cone, that means adding shims.

Reinstall the pinion, re-torque the pinion nut, and verify rolling torque preload.

Reinstall the differential case and readjust ring gear backlash to specification (adding depth shims decreases backlash, so the ring gear must be adjusted away from the pinion).

Reapply marking compound and retest pattern.

2. Low Pattern (Flank / Root Contact)

Visual Symptom : The contact impression is positioned deep in the tooth profile, digging down into the bottom root fillet (flank) of both drive and coast flanks.

Root Cause : The drive pinion is installed too deep (too close to the ring gear).

Corrective Action :

Move the pinion away from the ring gear. On a Meritor cage carrier, increase the thickness of the shim pack under the pinion bearing cage. On designs with shims behind the inner cup or cone, that means removing shims.

Reassemble and recheck pinion bearing rolling torque.

Reinstall differential case and readjust ring gear backlash to specification (removing depth shims increases backlash, so the ring gear must be adjusted toward the pinion).

Reapply marking compound and retest pattern.

3. Toe Pattern (Contact Jammed at Inner Apex)

Visual Symptom : The contact impression is concentrated at the narrow inner toe end of the tooth, running off the inner edge.

Root Cause : Ring gear backlash is too small (ring gear is positioned too close to the drive pinion).

Corrective Action :

Loosen the threaded adjuster ring on the tooth side of the ring gear.

Tighten the threaded adjuster ring on the back side of the ring gear by an identical amount.

This shifts the ring gear away from the pinion, INCREASING backlash (staying within the OEM range) and moving the pattern toward the heel.

Re-torque bearing cap bolts, recheck housing spread, and retest pattern.

4. Heel Pattern (Contact Jammed at Outer Edge)

Visual Symptom : The contact impression is concentrated at the wide outer heel end of the tooth, running off the outer edge.

Root Cause : Ring gear backlash is too large (ring gear is positioned too far from the drive pinion).

Corrective Action :

Loosen the threaded adjuster ring on the back side of the ring gear.

Tighten the threaded adjuster ring on the tooth side of the ring gear by an identical amount.

This shifts the ring gear toward the pinion, DECREASING backlash (staying within the OEM range) and moving the pattern toward the toe.

Re-torque bearing cap bolts, recheck housing spread, and retest pattern.

Comprehensive Diagnostic and Correction Matrix

Pattern Fault Observed Physical Gear Misalignment Primary Correction Required Secondary Correction Required

High Pattern (Crown / Face contact) Pinion not deep enough Move pinion toward ring gear (Meritor: thinner cage shim pack) Reset backlash using threaded adjuster rings

Low Pattern (Root / Flank contact) Pinion too deep in gear mesh Move pinion away from ring gear (Meritor: thicker cage shim pack) Reset backlash using threaded adjuster rings

Toe Pattern (Contact off inner edge) Ring gear too close to pinion INCREASE backlash (move ring gear away) Maintain carrier bearing housing spread

Heel Pattern (Contact off outer edge) Ring gear too far from pinion DECREASE backlash (move ring gear closer) Maintain carrier bearing housing spread

High-Heel Combined Pinion shallow; backlash excessive Move pinion toward ring gear first DECREASE backlash to correct heel position

Low-Toe Combined Pinion too deep; backlash tight Move pinion away from ring gear first INCREASE backlash to correct toe position

Important

If tooth contact patterns on the drive and coast flanks appear completely contradictory (e.g., high on drive side but low on coast side), inspect for a bent pinion shaft, a warped ring gear mounting flange, or severely worn carrier housing bearing saddle bores. Such defects prevent proper gear mesh and require component replacement.