Study guide
8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis
ASE T3 Drive Train Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Drive Train Fundamentals
1.1 ASE T3 Exam Format, Scoring, and Technician A/B Question Strategy 1.2 Medium/Heavy Truck Drive Train Architecture and Shop Safety
2 Clutch Construction & Actuation Systems
2.1 Push-Type vs. Pull-Type Clutches and Two-Plate Construction 2.2 Clutch Release Linkages, Hydraulic Systems, and Free Pedal Adjustment 2.3 Clutch Brake Operation, Types, Clearance, and Squeeze Adjustment 2.4 Release Bearings, Cross-Shafts, Clutch Safety Switches, Input Shaft Wear, and Clutch Torque Ratings
3 Clutch Adjustment, Maintenance & Troubleshooting
3.1 Manual vs. Self-Adjusting Clutches and Internal Adjustment Procedures 3.2 Flywheel Inspection, Resurfacing, Pilot Bearings, and Housing Alignment 3.3 Diagnosing Slip, Chatter, Drag, and AMT Clutch Actuators & Calibration
4 Manual Transmission Mechanics, Overhaul & Transfer Cases
4.1 Heavy-Duty Manual Transmission Layout: Twin Countershafts & Floating Main Shaft 4.2 Shift Bar Housings, Rails, Shift Forks, Detents, and Interlock Mechanisms 4.3 Main Box Power Flow, Sliding Clutches, and Gear Ratios 4.4 Transmission Lubrication, Cooling, Filtration, and PTO Installation & Backlash 4.5 Transmission Removal, Mounts, Leaks, and Overhaul Inspection (Shafts, Bearings, Reverse Idlers, Synchronizers, Cases) 4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles
5 Auxiliary Sections, Air Shifts, AMTs & Transmission Electronics
5.1 Auxiliary Gearing: Range and Splitter Section Design and Power Flow 5.2 Air Shift Systems: Roadranger Valves, Slave Valves, Cylinders, and Regulators 5.3 Diagnosing Gear Jump-Out, Gear Clash, Hard Shifting, and Bearing Noise by Gear 5.4 Automated Manual Transmissions (AMT): Actuators, Sensors, Diagnostics, and Calibration 5.5 Transmission Electrical Circuits: Speed Sensors, Electronic Speedometer Drives, Neutral and Reverse Switches, and Temperature Senders 5.6 Electronic Shift Controls and Diagnosis: In-Cab Selectors, Circuit Testing, Fault Codes, and J1939 Data-Link Faults
6 Driveshafts & Universal Joints
6.1 Driveline Operating Angles, Digital Inclinometers, and Torsional Angle Cancellation 6.2 Driveshaft Phasing, Spline Alignment, Runout Limits, and Dynamic Balancing 6.3 Heavy-Duty Universal Joint Types (Half-Round, Full-Round, Wing), Inspection, and Lube 6.4 Center Support Bearings, Slip Yokes, and Driveline Vibration Diagnostics (First vs. Second Order)
7 Drive Axles, Tandems, Power Dividers & Differential Locks
7.1 Drive Axle Configurations: Single-Reduction, Double-Reduction, and Tandem Through-Shaft 7.2 Interaxle Differential (Power Divider) Operation, Air Lockouts, and Spinout Prevention 7.3 Standard Differential Nest: Side Gears, Spider Cross, Pinions, and Thrust Washers 7.4 Driver-Controlled Main Differential Locks (DCDL): Operation, Operating Rules, Sensor Switch, and Service
8 Differential Setup, Axle Service, Lubrication & Wheel Ends
8.1 Carrier Setup: Pinion Depth, Bearing Preload, and Backlash Adjustment 8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections 8.3 Full-Floating Axles, Wheel Bearings, Hub Seals, and Drive vs. Coast Noise Diagnosis 8.4 Drive Axle Lubrication, Fill Procedures, Leaks, Carrier Removal, Housings, Lube Pumps, and Temperature Indicators 8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis
8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis
Key Takeaways Explain This Topic AI
ConMet PreSet hubs use a precision spacer to set bearing clearance, so the spindle nut is torqued without the conventional back-off.
ConMet PreSet Plus drive hubs are installed by torquing the spindle nut to 500 lb-ft while rotating the hub, with no back-off.
Bendix checks a WS-24 wheel speed sensor at 1,200–2,700 ohms, and for at least 0.25 VAC at the ECU with the wheel turned at 1/2 revolution per second.
If a sensor's output is low, Bendix says to push it back toward the tone (exciter) ring until it touches, then retest before replacing it.
Excessive wheel bearing end play, beyond RP 618A's 0.001–0.005 in. window, can let the tone ring move away from the sensor and set intermittent ABS codes.
Last updated: September 2026
8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis
The drive axle task list ends at the wheel. It covers diagnosing wheel bearing noise and damage ; checking hub seals and axle flange gaskets for leaks; servicing extended-service (preset and unitized) bearing assemblies ; and checking, testing, cleaning, adjusting or replacing wheel speed sensors and tone (exciter) rings . Conventional adjustable bearings and the TMC RP 618A procedure were covered in section 8.3.
1. Diagnosing Wheel Bearing Noise and Damage
Symptom pattern: a growl or roar that follows road speed and does not change with throttle (drive, coast, or float). It usually gets louder when the vehicle sways or turns and loads that wheel end. Differential and pinion noises change with throttle; wheel bearing noise does not.
Check end play: mount a dial indicator and push-pull the hub along the spindle axis. For conventionally adjusted bearings, TMC RP 618A's target is 0.001–0.005 in. Too much means loose adjustment or worn bearings; zero end play with a hot hub means preload.
Read the damage:
- Condition Appearance Usual Cause
- Fatigue spalling Flaking pits on races or rollers Normal end of life, overload, or incorrect adjustment
- Brinelling Indentations spaced like the rollers Impact loads or improper installation
- Etching/corrosion Stains and pitting Water in the lubricant (failed seal, plugged breather)
- Heat discoloration Blue or brown races and rollers Lack of lubrication or preload
- Abrasive wear Dull, scratched surfaces Contaminated oil or grease
Always find the cause — low hub oil, a leaking seal, a plugged breather, or incorrect adjustment — before replacing bearings.
2. Hub Seals and Axle Flange Gaskets
Wheel seals: oil on the brake linings or the inside of the wheel means a leaking seal. Check for a plugged axle breather, overfilling, a seal installed cocked (use the seal manufacturer's driver), and loose bearing adjustment that lets the hub wobble on the seal.
Axle flange joint: the gasket and flange of the axle shaft must fit flat against the wheel hub (Meritor). If Meritor's silicone option is used instead of a gasket, apply a 0.125-inch (3 mm) bead around the hub mating surface and around the edge of each fastener hole. Tighten the stud nuts to specification with the correct hardened washers or lock washers.
3. Extended-Service Hubs: Preset and Unitized Assemblies
Extended-service wheel ends remove the adjustment step that causes so many bearing failures:
Preset (pre-adjusted) hubs: ConMet's PreSet design uses a precision-machined spacer between the tapered roller bearings to control their spacing, so there is no manual adjustment. The installer torques the spindle nut to the specification and does not back it off .
ConMet PreSet with a double-nut or jam-nut system: torque the inner nut to 300 lb-ft (do not back off; advance it as needed to install the locking ring), then torque the outer nut to 200 lb-ft and engage any locking device.
ConMet PreSet Plus (integrated spindle nut): torque the spindle nut to 500 lb-ft on a drive or trailer hub (300 lb-ft on a steer hub) while rotating the hub , with no back-off.
Unitized hub assemblies: some hubs are sealed units with bearings, seals, and lubricant built in. Meritor notes that its sealed, greased truck hub units need no maintenance, and that disassembling, lubricating, or repairing them voids the warranty. They are replaced as a unit when they fail.
Key rule: never apply the conventional RP 618A "back-off" to a preset or unitized hub, and never mix preset hub parts with conventional bearings or spacers. Follow the hub maker's torque, locking-device, and end-play verification instructions exactly.
4. ABS Wheel Speed Sensors and Tone Rings
Each ABS-monitored wheel has a tone (exciter) ring on the hub and a wheel speed sensor held in a mounting block by a spring clamping sleeve . The sensor is pushed in until it touches the tone ring. As the ring turns, normal bearing end play pushes the sensor back to a small working gap. The sensor produces an AC signal whose frequency matches wheel speed.
Bendix WS-24 sensor checks:
Inspect the sensor cable for cuts, pinching, wear, or exposed wires, and the connectors for corrosion and loose pins.
Resistance: at ambient temperature (0–100°F), resistance across the sensor should be 1,200–2,700 ohms . Outside that range, replace the sensor.
Output: with the wheel raised and the parking brakes released, turn the wheel by hand at at least 1/2 revolution per second . The AC voltage at the ECU across the sensor terminals should be at least 0.25 VAC .
Low output: gently push the sensor toward the wheel until it touches the exciter ring , and retest. If output is still low, replace the sensor using a new sensor kit with its clamping sleeve.
If resistance and voltage are good, the sensor is not the problem. Look for pinched or chafed harness wires, loose pins, or ECU connector problems.
Tone ring problems: a cracked, loose, or damaged ring, missing teeth, or ring runout gives an erratic signal. Excessive wheel bearing end play lets the hub wander away from the sensor and causes intermittent low-signal codes, which is one more reason to hold end play in specification. When replacing a hub or ring, protect the ring from damage and make sure it is fully seated.
Safety: Bendix warns that on vehicles with automatic traction control (ATC) , ATC must be disabled before any maintenance where drive-axle wheels are lifted and turning. Otherwise the system can apply brakes or change engine torque unexpectedly.