Study guide
4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles
ASE T3 Drive Train Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Drive Train Fundamentals
1.1 ASE T3 Exam Format, Scoring, and Technician A/B Question Strategy 1.2 Medium/Heavy Truck Drive Train Architecture and Shop Safety
2 Clutch Construction & Actuation Systems
2.1 Push-Type vs. Pull-Type Clutches and Two-Plate Construction 2.2 Clutch Release Linkages, Hydraulic Systems, and Free Pedal Adjustment 2.3 Clutch Brake Operation, Types, Clearance, and Squeeze Adjustment 2.4 Release Bearings, Cross-Shafts, Clutch Safety Switches, Input Shaft Wear, and Clutch Torque Ratings
3 Clutch Adjustment, Maintenance & Troubleshooting
3.1 Manual vs. Self-Adjusting Clutches and Internal Adjustment Procedures 3.2 Flywheel Inspection, Resurfacing, Pilot Bearings, and Housing Alignment 3.3 Diagnosing Slip, Chatter, Drag, and AMT Clutch Actuators & Calibration
4 Manual Transmission Mechanics, Overhaul & Transfer Cases
4.1 Heavy-Duty Manual Transmission Layout: Twin Countershafts & Floating Main Shaft 4.2 Shift Bar Housings, Rails, Shift Forks, Detents, and Interlock Mechanisms 4.3 Main Box Power Flow, Sliding Clutches, and Gear Ratios 4.4 Transmission Lubrication, Cooling, Filtration, and PTO Installation & Backlash 4.5 Transmission Removal, Mounts, Leaks, and Overhaul Inspection (Shafts, Bearings, Reverse Idlers, Synchronizers, Cases) 4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles
5 Auxiliary Sections, Air Shifts, AMTs & Transmission Electronics
5.1 Auxiliary Gearing: Range and Splitter Section Design and Power Flow 5.2 Air Shift Systems: Roadranger Valves, Slave Valves, Cylinders, and Regulators 5.3 Diagnosing Gear Jump-Out, Gear Clash, Hard Shifting, and Bearing Noise by Gear 5.4 Automated Manual Transmissions (AMT): Actuators, Sensors, Diagnostics, and Calibration 5.5 Transmission Electrical Circuits: Speed Sensors, Electronic Speedometer Drives, Neutral and Reverse Switches, and Temperature Senders 5.6 Electronic Shift Controls and Diagnosis: In-Cab Selectors, Circuit Testing, Fault Codes, and J1939 Data-Link Faults
6 Driveshafts & Universal Joints
6.1 Driveline Operating Angles, Digital Inclinometers, and Torsional Angle Cancellation 6.2 Driveshaft Phasing, Spline Alignment, Runout Limits, and Dynamic Balancing 6.3 Heavy-Duty Universal Joint Types (Half-Round, Full-Round, Wing), Inspection, and Lube 6.4 Center Support Bearings, Slip Yokes, and Driveline Vibration Diagnostics (First vs. Second Order)
7 Drive Axles, Tandems, Power Dividers & Differential Locks
7.1 Drive Axle Configurations: Single-Reduction, Double-Reduction, and Tandem Through-Shaft 7.2 Interaxle Differential (Power Divider) Operation, Air Lockouts, and Spinout Prevention 7.3 Standard Differential Nest: Side Gears, Spider Cross, Pinions, and Thrust Washers 7.4 Driver-Controlled Main Differential Locks (DCDL): Operation, Operating Rules, Sensor Switch, and Service
8 Differential Setup, Axle Service, Lubrication & Wheel Ends
8.1 Carrier Setup: Pinion Depth, Bearing Preload, and Backlash Adjustment 8.2 Ring and Pinion Tooth-Contact Pattern Diagnosis (Drive vs. Coast) and Corrections 8.3 Full-Floating Axles, Wheel Bearings, Hub Seals, and Drive vs. Coast Noise Diagnosis 8.4 Drive Axle Lubrication, Fill Procedures, Leaks, Carrier Removal, Housings, Lube Pumps, and Temperature Indicators 8.5 Wheel-End Systems: Preset and Unitized Hubs, ABS Wheel Speed Sensors and Tone Rings, and Wheel Bearing Diagnosis
4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles
Key Takeaways Explain This Topic AI
Meritor MTC transfer cases need at least 60 psi of air at all times to shift correctly; the shop shifting check applies 60 psi to each port.
Meritor says to engage the front-axle declutch only in poor conditions, with the truck stationary or below 10 mph, and never while wheels are slipping or on a steep grade.
Meritor MTC transfer cases use SAE 50W full-synthetic oil; do not use multi-viscosity engine oil or EP GL-5 gear oil.
Meritor's transfer case vibration check limits driveline angles to 5 degrees, with no more than 1.5 degrees difference between angles.
Measure driveline and PTO driveshaft angles both loaded and unloaded, because suspension deflection changes them.
Last updated: September 2026
4.6 Transfer Cases, PTO Controls, and PTO Driveshaft Angles
The last transmission task on the ASE T3 list — inspect, adjust, repair or replace transfer case assemblies and controls — matters on all-wheel-drive dump trucks, utility trucks, fire apparatus, and military-style vehicles. The driveshaft area adds PTO driveshafts to the angle-measurement task. This section uses Meritor's MTC-series transfer case manual as the reference design.
1. What a Transfer Case Does
A transfer case sits behind the transmission and splits power between the rear drive axle(s) and a front drive axle. A typical heavy-duty unit (Meritor MTC series) contains:
An input shaft and helical gear train with an idler gear.
A high/low range sliding clutch collar with high- and low-range helical drive gears. Cummins/Meritor data list a low range around 2:1 on several MTC models (for example 2.05:1).
A front-axle declutch that connects or disconnects the front output.
An optional neutral position and power take-off (PTO) on some models.
A speed sensor , indicator switches , a ceramic magnet to catch wear particles, a breather (or neutral air-control solenoid), and on some models an oil pump and cooler option.
2. Air Controls and Shifting Rules (Meritor MTC)
The range, declutch, and neutral functions are air-shifted:
Rule Meritor Guidance
Air supply The transfer case requires at least 60 psi at all times to operate correctly.
Front-axle declutch Engage only under poor operating conditions , with the vehicle stationary or at a constant low speed below 10 mph . Do not engage it when the wheels are slipping or when moving up or down a steep hill or grade. Engaging it changes turning and steering response.
Range shifts Shift between high and low with the vehicle stationary . On automatic-transmission trucks, apply the parking brake with the transmission in neutral. Do not use low range under normal operating conditions.
Part-time 4x4/6x6 use Meritor's newer MTC manual recommends speeds under 20 mph for part-time all-wheel-drive operation.
Shop shifting check: With the transfer case on the bench or in the truck, apply 60 psi or more to the front-axle declutch port and turn the input by hand. The front output should turn at the same rate as the rear output. Then remove the air and repeat at the high-range, low-range, and (for PTO-equipped cases) neutral ports to confirm each shift.
Won't shift or declutch: Check air pressure first (at least 60 psi), then the indicator light and sensor. Next check the air control and supply for leaks or contamination, then the shift piston, O-rings, and return spring. Only then remove the case to inspect the shift collar, engagement teeth, shift fork, and fork bore.
3. Transfer Case Lubrication and Temperature
Oil: Meritor specifies SAE 50W full-synthetic oil in MTC transfer cases and warns not to use multi-viscosity engine oils or EP GL-5 gear oils; damage can result.
Level: fill to the level Meritor specifies at the fill plug, on level ground. An incorrect level causes excess heat.
Temperature: Meritor notes that MTC-4208, -4209 and -4210 cases may run above 300°F (148°C) in long high-speed line-haul or utility use. If oil reaches 350°F (177°C) , stop the vehicle immediately and find the cause. An oil cooler is offered for trucks that spend long periods at high speed with overdrive transmissions.
Magnet: inspect and clean the case magnet at oil changes; heavy metal buildup means a gear or bearing is failing.
4. Noise, Vibration, and Leaks
Meritor's transfer case vibration flowchart starts with the driveline, not the case:
Measure all driveline angles. Angles should not exceed 5 degrees , and the difference between any of the angles should not exceed 1-1/2 degrees . Meritor calls excessive driveline angles the leading cause of drivetrain vibration and noise.
Check driveline balance, U-joints for wear or damaged rollers, and the case mounting fasteners and brackets for looseness or breakage.
Only then look inside for worn bearings or gears.
Leaks usually come from output seals, the PTO mounting, cover gaskets, or a plugged breather.
5. PTO Controls
A PTO can be shifted by cable or lever, by air, or electrically/hydraulically:
Clutch-shift (non-clutched) PTOs on manual transmissions are engaged with the clutch released and the gearing stopped, just like selecting a gear from rest.
"Hot-shift" PTOs have an internal clutch pack and can engage while the gearing is turning. They are common on automatic transmissions.
An indicator switch and light tells the driver the PTO is engaged. If a PTO does not engage or disengage, Meritor's first checks are the air connection to the PTO shift port and the indicator light and switch.
Noise tells you about gear mesh. Muncie's rule is that a whine that rises with rpm means the PTO is mounted too tight (add a gasket), and a clatter means it is too loose (remove a gasket). Correct backlash is 0.006–0.012 in. (section 4.4).
6. PTO Driveshaft Angles, Loaded and Unloaded
The ASE task for driveline angles specifically includes PTO driveshafts and measuring loaded and unloaded :
Treat a PTO driveshaft like any other two-joint shaft. Keep operating angles small and equal at both ends, and never at zero. Spicer's guidelines are at least 1/2 degree, equal within 1 degree, and no more than 3 degrees for vibration-free running. Spicer tightens the equal-angle rule to 1/2 degree for shafts in front of transfer cases or auxiliary devices.
Phase the yokes correctly, keep slip joints lubricated, and support long shafts.
Loaded vs. unloaded: as a truck is loaded, springs compress and the axle rotates, changing pinion angles. A body-mounted pump driven from a chassis-mounted PTO may also change angle as the chassis flexes. Measure at both conditions; a vibration that appears only when loaded often traces to angles that are acceptable empty but out of limits loaded.
Guarding: exposed PTO shafts must be guarded, and the PTO must be disengaged and locked out before anyone works near the shaft.