Study guide

12.2 Wheel Bearing Inspection, Preload & End-Play Adjustment (TMC RP 618)

ASE T4 — Brakes Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & ASE T4 Certification Overview

1.1 ASE T4 Exam Specifications, Structure & Test-Taking Strategy 1.2 Commercial Vehicle Brake Regulations, FMVSS 121 Standards & Safety

2 Chapter 2: Air Supply System — Generation, Cleaning & Regulation

2.1 Air Compressors & Governors 2.2 Air Dryers & Moisture Management 2.3 Reservoirs, Safety Valves & Leakage Testing

3 Chapter 3: Air Brake Control Valves & Circuit Distribution

3.1 Dual Circuit Architecture & Treadle (Foot) Valves 3.2 Relay Valves & Quick-Release Valves 3.3 Specialty Air Valves — Double Check, Ratio, Proportioning & Inversion

4 Chapter 4: Tractor-Trailer Air Brake Protection & Coupling

4.1 Tractor Protection Systems & Dashboard Manifold Valves 4.2 Gladhand Couplers, Trailer Supply & Service Lines

5 Chapter 5: S-Cam Foundation Brakes & Actuation

5.1 Brake Chambers & Pushrod Travel 5.2 Slack Adjusters — Manual & Automatic (ASA) Operation & Stroke Limits 5.3 S-Camshafts, Bushings, Rollers & Anchor Pins 5.4 Brake Shoes, Linings & Friction Codes 5.5 Brake Drums — Inspection, Measurement & Machining

6 Chapter 6: Heavy-Duty Air Disc Brakes (ADB)

6.1 Air Disc Brake Architecture & Caliper Mechanics 6.2 ADB Rotors, Brake Pads & Running Clearance 6.3 ADB Inspection, Diagnostic Troubleshooting & Maintenance

7 Chapter 7: Parking & Emergency Spring Brake Systems

7.1 Spring Brake Chamber Construction & Operation 7.2 Spring Brake Caging Safety & Mechanical Release 7.3 Anti-Compounding Systems & Pressure Delivery

8 Chapter 8: Hydraulic Brake Systems for Medium-Duty Trucks

8.1 Dual Master Cylinders & Hydraulic Circuits 8.2 Brake Fluids, Hydraulic Lines & Bleeding Procedures 8.3 Hydraulic Foundation Brakes — Calipers, Rotors, Drums & Wheel Cylinders 8.4 Hydraulic Valves — Metering, Proportioning, Pressure Differential & Load-Sensing 8.5 Driveline, Mechanical & Electronic Parking Brakes on Hydraulic-Braked Trucks

9 Chapter 9: Hydraulic Power Assist & Air-Over-Hydraulic Systems

9.1 Hydro-Boost & Hydraulic Power Brake Systems 9.2 Vacuum Boosters & Electric Auxiliary Vacuum Pumps 9.3 Air-Over-Hydraulic & Full-Power Hydraulic Systems

10 Chapter 10: Antilock Brake Systems (ABS) — Air & Hydraulic

10.1 ABS Principles, Configurations & Components 10.2 Wheel Speed Sensors & Tone Rings 10.3 Modulator Valves & Pneumatic/Hydraulic ABS Actuation 10.4 Trailer ABS, Power Line Carrier (PLC) & Diagnostics

11 Chapter 11: Automatic Traction Control (ATC), Electronic Stability Control (ESC) & Collision Mitigation

11.1 Automatic Traction Control (ATC) Operation & Diagnostics 11.2 Electronic Stability Control (ESC) & Roll Stability 11.3 Advanced Driver Assistance Systems (ADAS) & Collision Mitigation 11.4 Vehicle Modifications, Harness Repair & Verifying the Brake Repair

12 Chapter 12: Wheel Bearings & Wheel-End Service

12.1 Wheel Bearing Types, Hub Assemblies & Lubrication 12.2 Wheel Bearing Inspection, Preload & End-Play Adjustment (TMC RP 618) 12.3 Wheel Hub Seals, Spindles & Wheel-End Assembly

13 Chapter 13: Comprehensive Brake Diagnosis, Road Testing & ASE Problem Scenarios

13.1 Systematic Brake Diagnostic Strategies & Symptom Troubleshooting 13.2 Technician A / Technician B Case Studies & Exam Review

12.2 Wheel Bearing Inspection, Preload & End-Play Adjustment (TMC RP 618)

Key Takeaways Explain This Topic AI

TMC RP 618A sets the double-nut sequence as 200 lb-ft seating torque while rotating, back off one full turn, re-torque to 50 lb-ft while rotating, then a final back-off of 1/4 turn on drive and trailer axles, or 1/6 to 1/2 turn on steer (front non-drive) axles depending on spindle threads per inch and locking method.

Final wheel bearing end-play must be verified using a dial indicator with a rigid magnetic base attached to the hub, measuring between 0.001" and 0.005" (0.025 mm to 0.127 mm) of total axial movement without rocking the hub.

Spindle outer jam nuts require substantial clamping torque (200 to 400 lb-ft under TMC RP 618A, set by axle type, jam nut size, and washer style) to prevent the inner nut from loosening and maintain set end-play.

When securing double-nut assemblies with bendable tab lock washers, the technician must bend one inner tab inward over an inner nut flat and one outer tab outward over an outer jam nut flat; never bend tabs over nut corners.

Last updated: August 2026

The Technology & Maintenance Council (TMC) RP 618 Standard

Improper wheel bearing adjustment on commercial vehicles is a leading cause of catastrophic wheel-end failures, roadside wheel separations (wheel-offs), wheel-end fires, and erratic antilock braking system (ABS) operation. To establish an industry-wide, repeatable engineering protocol, the Technology & Maintenance Council (TMC) of the American Trucking Associations developed Recommended Practice (RP) 618: Wheel Bearing Adjustment Procedure .

TMC RP 618 provides exact numerical torque values and rotational back-off angles to achieve the mandatory running clearance window: 0.001" to 0.005" (0.025 mm to 0.127 mm) of axial end-play . BEARING RUNNING CLEARANCE SPECTRUM & OPERATING ZONES

  • [ Excessive Preload ] [ Target Running Clearance ] [ Excessive End-Play ]
  • <--------------------------|=============================|---------------------------->
  • Negative Clearance 0.001" to 0.005" (0.025-0.127mm) > 0.005" (Loose Hub)
  • Extreme friction heat • Optimal roller load sharing • Hub wobble & wheel shake
  • Rapid fatigue / spalling • Full lubricant film integrity • Wheel seal leaks & lining soak
  • Bearing seizure • Extended bearing fatigue life • ABS sensor gap fault codes
  • Potential wheel-off fire • Precise brake rotor alignment • Accelerated edge tire wear
  • The 3-Step Double-Nut Adjustment Sequence

On conventional commercial axles featuring standard threaded spindles and double hex nuts (an inner adjusting nut, a locking ring/washer, and an outer jam nut), the technician must follow the standardized 3-step sequence using a calibrated torque wrench.

Loading diagram...

Detailed Step-by-Step Breakdown: +-----------------------------------------------------------------------------------+

  • | TMC RP 618 THREE-STEP DOUBLE-NUT ADJUSTMENT |
  • +-----------------------+-----------------------------+-----------------------------+
  • | PROCEDURE STEP | TORQUE / ROTATIONAL ACTION | ENGINEERING PURPOSE |
  • +-----------------------+-----------------------------+-----------------------------+
  • | Step 1: Initial Seat | Torque inner nut to | Overcomes lubricant film and|
  • | | **200 lb-ft** while | forces all rollers, cups, |
  • | | rotating the hub/drum | and cones squarely in place |
  • +-----------------------+-----------------------------+-----------------------------+
  • | Step 2: Full Back-Off | Back off inner nut | Completely removes seating |
  • | | **1 full turn (360°)** | clamp load to prepare for |
  • | | | final adjustment |
  • +-----------------------+-----------------------------+-----------------------------+
  • | Step 3: Final Setting | Torque inner nut to | Re-establishes zero-lash |
  • | | **50 lb-ft** while rotating | reference point under light |
  • | | the hub, then BACK OFF per | dynamic load, then the |
  • | | the RP 618A axle table: | back-off creates the |
  • | | • **Drive**: 1/4 turn | 0.001"-0.005" end play |
  • | | • **Trailer**: 1/4 turn | • 1/4 turn = 90° = 1.5 flats|
  • | | • **Steer (front non-drive)**| • 1/6 turn = 60° = 1 flat |
  • | | 1/6, 1/4, or 1/2 turn | • Steer value depends on |
  • | | per threads-per-inch | TPI and lock method |
  • +-----------------------+-----------------------------+-----------------------------+

Caution

Always Rotate While Torquing : In both Step 1 (200 lb-ft) and Step 3 (50 lb-ft), the hub or brake drum must be continuously rotated by hand in both directions while torque is applied. Torquing a stationary hub traps the tapered rollers at a slight skew, leading to false torque readings. When the truck is subsequently driven, the rollers align themselves, resulting in a dangerously loose hub assembly.

Outer Jam Nut Torquing & Locking Hardware

Once the inner adjusting nut has been backed off to its final position, the locking hardware and outer jam nut must be installed. Torquing the outer jam nut exerts high axial clamping force through the spindle threads, driving the inner nut against the spindle thread flanks and slightly reducing bearing end-play. +-----------------------------------------------------------------------------------+

  • | OUTER JAM NUT FINAL TORQUE SPECIFICATIONS (TMC RP 618) |
  • +--------------------------------------+--------------------------------------------+
  • | AXLE TYPE & LOCKING HARDWARE | OUTER JAM NUT FINAL TORQUE (RP 618A) |
  • +--------------------------------------+--------------------------------------------+
  • | Steer (double nut), jam nut under | **200 to 300 lb-ft** (271 to 407 N·m) |
  • | 2-5/8" | |
  • +--------------------------------------+--------------------------------------------+
  • | Steer (double nut), jam nut 2-5/8" | **300 to 400 lb-ft** (407 to 542 N·m) |
  • | and over | |
  • +--------------------------------------+--------------------------------------------+
  • | Steer (single nut) spindles locked | (no outer jam nut; the cotter pin holds |
  • | by a cotter pin | the adjusting nut) |
  • +--------------------------------------+--------------------------------------------+
  • | Drive axle, DOWEL-type washer | **300 to 400 lb-ft** (407 to 542 N·m) |
  • +--------------------------------------+--------------------------------------------+
  • | Drive axle, TANG-type (bendable) | **200 to 275 lb-ft** (271 to 373 N·m) |
  • | washer | |
  • +--------------------------------------+--------------------------------------------+
  • | Trailer axle, jam nut under 2-5/8" | **200 to 300 lb-ft** (271 to 407 N·m) |
  • +--------------------------------------+--------------------------------------------+
  • | Trailer axle, jam nut 2-5/8" and | **300 to 400 lb-ft** (407 to 542 N·m) |
  • | over | |
  • +--------------------------------------+--------------------------------------------+
  • Locking Hardware Types & Installation Rules

Bendable Tab Lock Washers :

Install the washer over the spindle between the inner adjusting nut and outer jam nut, ensuring the internal tab engages the spindle keyway.

Torque the outer jam nut to full specification.

Using a brass drift and hammer, bend one washer tang INWARD over an inner nut flat , and bend one opposing washer tang OUTWARD over an outer jam nut flat .

Never bend tabs over the corners (hex points) of the nuts, as sharp corners shear the metal tabs during road vibration.

Dowel Pin Washers & Lock Rings :

On dowel-pin systems, the inner nut features an integral protruding pin. The lock ring contains a circle of mating holes and an internal key that fits the spindle slot.

Slide the lock ring over the spindle until the dowel pin engages one of the holes. If the pin does not align with a hole, remove the lock ring, flip it over , or slightly adjust the inner nut to the nearest hole without exceeding specification limits.

Single-Nut Systems (Axilok / Pro-Torq) :

Utilize a single heat-treated nut incorporating spring-steel locking clips or snap rings that positively lock into spindle keyways after torque setting. BENDABLE TAB WASHER LOCKING ORIENTATION

  • [ Spindle Centerline ]
  • |
  • +-------------------v-------------------+
  • | [ Inner Adjusting Nut ] |
  • | | |
  • | +---> Bend ONE Tang INWARD |
  • | over Inner Nut Flat |
  • +---------------------------------------+
  • | [ Lock Washer with Spindle Key ] |
  • +---------------------------------------+
  • | [ Outer Jam Nut ] |
  • | | |
  • | +---> Bend ONE Tang OUTWARD |
  • | over Outer Jam Nut Flat |
  • +---------------------------------------+
  • Dial Indicator Setup & End-Play Verification

After torquing the outer jam nut to final specification, the technician must measure and document final bearing end-play using a dial indicator. Estimating end-play by grabbing the tire and "feeling for play" is strictly prohibited by TMC standards. DIAL INDICATOR MEASUREMENT SETUP

  • [ Rigid Magnetic Base ]
  • |
  • v Attached solidly to Hub Face or Drum Face
  • +-------------------------+
  • | |
  • | +-----------------+ |
  • | | Dial Indicator | |
  • | | Gauge Body | |
  • | +--------+--------+ |
  • +------------|------------+
  • |
  • v Plunger aligned parallel to Spindle Centerline
  • [ Contact Tip ] -------> Touching machined Spindle Center End

Step-by-Step Measurement Procedure:

Thoroughly clean the hub face or brake drum mounting surface and attach the rigid magnetic base of the dial indicator assembly solidly to the hub.

Position the indicator arm so that the contact plunger sits parallel to the spindle centerline and rests firmly against the flat, machined end of the spindle shaft with 0.050" of pre-travel loaded on the gauge.

Zero the dial indicator bezel.

Grasp the hub or brake drum at the 3 o'clock and 9 o'clock positions (or 6 and 12 o'clock). Push straight inward toward the axle centerline with steady, solid force (approx. 50–100 lbs) without twisting or rocking the hub. Observe the indicator needle settle.

Pull straight outward away from the vehicle with equal force without rocking. Note the total needle travel on the dial.

Mandatory Acceptance Criteria : Total indicator needle movement must read between 0.001" and 0.005" (0.025 mm to 0.127 mm) .

Diagnostic Corrections if Out of Specification:

If End-Play is Less than 0.001" (Too Tight / Zero Play) : The assembly risks bearing preload and thermal destruction. Disassemble the outer jam nut, back off the inner adjusting nut slightly (to the next lock position), re-torque the jam nut, and re-test.

If End-Play Exceeds 0.005" (Too Loose) : The hub will wobble, damaging oil seals, triggering ABS sensor air gap faults, and causing brake rotor runout. Disassemble the outer jam nut, tighten the inner adjusting nut slightly, re-torque the jam nut, and re-test.