Study guide
13.3 Electric Fuel Supply & Transfer Pump Control Circuits
ASE T6 Electrical/Electronic Systems Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction: About the ASE T6 Test
0.1 ASE T6 Test Specifications, Content Areas & Task List
2 Chapter 1: Electrical Fundamentals, Circuits & Meter Diagnostics
1.1 Ohm's Law, Power Calculations & Truck Circuit Fundamentals 1.2 Digital Multimeter (DMM) & Inductive Clamp Meter Operations 1.3 Voltage Drop Testing Principles & High-Resistance Diagnostics
3 Chapter 2: Circuit Faults, Protection & Control Devices
2.1 Circuit Fault Diagnosis — Opens, Shorts & Intermittents 2.2 Parasitic Drain Diagnosis & Circuit Protection Devices 2.3 Relays, Solenoids, Spike Suppression Diodes & Clamping
4 Chapter 3: Schematics, Waveforms & Advanced Diagnostics
3.1 Heavy-Truck Electrical Schematics & Wire Harness Service 3.2 Digital Storage Oscilloscope (DSO) Operation & Waveform Analysis 3.3 Electronic Control Systems Diagnostic Strategy & Calibration
5 Chapter 4: Commercial Truck Batteries & Battery Management
4.1 Heavy-Duty Battery Construction, Group 31 Specifications & Chemistry 4.2 State-of-Charge & Battery Capacity/Load Testing 4.3 Battery Configurations, Charging, Jump-Starting & LVD Systems
6 Chapter 5: Heavy-Duty Cranking Systems & Diagnosis
5.1 Heavy-Duty Starter Motors, Solenoids & Integrated Magnetic Switches 5.2 Starter Control Circuits, Overcrank Protection & Inhibit Logic 5.3 Cranking System Diagnostics, Current Draw & Voltage Drop
7 Chapter 6: Heavy-Duty Alternator Operation & Control
6.1 Alternator Principles, Three-Phase Rectification & Brushless Designs 6.2 Voltage Regulation, Remote Sensing & Smart Charging 6.3 Mechanical Drive Systems, Pulleys & Alternator Mountings
8 Chapter 7: Charging System Testing & Troubleshooting
7.1 Alternator Output Testing & Cable Voltage Drops 7.2 AC Ripple Testing & Diode Diagnosis 7.3 Overcharging, Undercharging & No-Charge Troubleshooting
9 Chapter 8: Exterior Lighting & Cab Control Systems
8.1 Headlamp Systems, LED Technology & Daytime Running Lights 8.2 Stoplight, Turn Signal, Hazard Flashers & Electronic Body Modules 8.3 Backup Warning Devices, Cab Interior & Marker Lighting
10 Chapter 9: Trailer Lighting & FMVSS 108 Compliance
9.1 SAE J560 7-Way Trailer Electrical Connector & Cord Diagnostics 9.2 FMVSS 108 Standards & Commercial Vehicle Lighting Inspection
11 Chapter 10: Heavy-Duty Data Networks & Multiplexing
10.1 Truck Multiplexing Concepts & Electronic Control Architecture 10.2 SAE J1939 CAN Datalink Architecture & Physical Layer 10.3 J1939 Datalink Testing, Fault Diagnostics & SPN/FMI Codes
12 Chapter 11: Gauges, Warning Devices & Driver Information Systems
11.1 Electronic Instrument Clusters & Datalink Gauges 11.2 Analog & Digital Senders, Transducers & Warning Indicators 11.3 Horns, Supplemental Restraints & Safety Circuits
13 Chapter 12: Cab Electrical Accessories & Auxiliary Systems
12.1 Heavy-Duty Windshield Wipers & Washer Systems 12.2 Power Windows, Door Locks & Heated Mirror Systems 12.3 HVAC Electrical Controls, Inverters, Shore Power & APUs
14 Chapter 13: Cruise, Cooling-Fan & Fuel-Supply Electrical Controls
13.1 Cruise Control Electrical Controls & Components 13.2 Engine Cooling Fan Electrical Control Circuits 13.3 Electric Fuel Supply & Transfer Pump Control Circuits
15 Chapter 14: Cab Power Outlets, Telematics & Fleet Data Systems
14.1 Cigarette Lighter, Auxiliary Power Outlets & Cab Accessory Feeds 14.2 Telematics, Electronic Logging Devices & Fleet Data Interfaces
13.3 Electric Fuel Supply & Transfer Pump Control Circuits
Key Takeaways Explain This Topic AI
Electric fuel supply (lift) pumps on commercial diesels are ECM-controlled through a relay and typically prime for a few seconds at key-on, then shut off unless the ECM detects engine rotation — a deliberate safety strategy that prevents pumping fuel after a crash or a line failure.
Current draw is the most informative electric fuel pump test: a pump drawing well above specification is dragging mechanically or fighting a restriction, while a pump drawing well below specification is worn, cavitating, or being starved of voltage.
Maximum allowable voltage drop from the battery to the pump under running load is about 0.5 V on the insulated side and 0.2 V on the ground side; a corroded frame ground behind the fuel tank is a far more common cause of slow cranking-fuel delivery than a failed pump.
Saddle-tank and auxiliary-tank transfer pumps are separate circuits controlled by a dash switch, a float/level switch, or a body controller, and must include run-dry and overfill protection because they move fuel between tanks rather than feeding the engine.
A restricted primary fuel filter raises pump current and lowers delivered flow at the same time, so filter restriction must be ruled out before an electric supply pump is condemned.
Last updated: September 2026
13.3 Electric Fuel Supply & Transfer Pump Control Circuits
The official ASE T6 task list requires a technician to inspect, test, and replace electric fuel supply/transfer pump control components . This is an electrical task on a fuel system, and the distinction matters: T6 is not asking you to rebuild an injection pump. It is asking whether you can prove that the electrical circuit feeding a fuel pump is delivering the right voltage, at the right time, with the right current, and whether you can tell a control fault from a hydraulic restriction.
Two different pumps fall under this task:
The fuel supply (lift or transfer) pump that pulls fuel from the tank, pushes it through the primary filter/water separator, and supplies the high-pressure injection pump.
The tank-to-tank transfer pump that moves fuel between saddle tanks or from an auxiliary/belly tank into the main supply tank.
Electric Fuel Supply Pumps: Control Strategy
On medium-duty chassis and on several heavy-duty engine families, the lift pump is an electric gear or vane pump rather than a camshaft-driven mechanical pump. Its circuit is deliberately conservative:
Key-on prime. When the ignition switch moves to RUN, the ECM (or body controller) energizes the fuel pump relay for a fixed prime interval — commonly a few seconds up to about 30 seconds depending on engine family — to fill the supply gallery and purge air before cranking.
Prime timeout. If the ECM does not detect engine rotation from the crankshaft position sensor by the end of that interval, it de-energizes the relay . This is a safety strategy: after a rollover or a ruptured supply line, the pump must not keep delivering fuel.
Run. Once the ECM sees engine speed, the relay stays energized continuously while the engine runs.
Shutdown. Key-off drops the relay immediately.
Important
A driver complaint of "it starts if I cycle the key three or four times" is a classic electric lift pump symptom. Each key cycle adds one more prime interval and a little more fuel to the gallery. It usually points to a pump that has lost flow, a leaking check valve or suction-side air leak that lets the gallery drain back, or a restricted primary filter — not to the starting system.
The circuit
A typical supply pump circuit contains only a handful of components:
- Element Function What fails
- Fuse or maxi-fuse Overcurrent protection sized above running current Nuisance opening when the pump drags
- Relay terminal 30 Unswitched or ignition-switched battery feed Corroded socket terminal, fretting corrosion
Relay terminals 85/86 Coil, controlled by an ECM low-side driver Open coil, missing suppression diode, reversed polarity on a diode-suppressed relay
- Relay terminal 87 Switched output to the pump Burned contacts causing voltage drop under load
- Pump motor Electric gear/vane pump Worn brushes, dragging armature, seized rotor
Chassis ground Return path at a frame or crossmember stud Road-salt corrosion — the single most common fault on this circuit
Because many pumps mount on or near the frame rail behind the fuel tank, the ground stud lives in the worst environment on the truck: constant wheel spray, brine, and abrasion.
- Electrical Testing: Current, Voltage Drop, Ground
- 1. Current draw
Current draw is the most diagnostic single measurement on an electric fuel pump because it reports the pump's mechanical condition, not just its circuit.
Use a low-range DC clamp ammeter around the pump supply lead, zeroed in position, or a DSO with a current probe to see the commutation pattern.
Compare the measured value against the OEM specification for that pump — commercial lift pumps vary widely, so a memorized number is worthless.
Above specification = the pump is working hard: a dragging armature or bearing, a seizing rotor, or a downstream restriction (plugged primary filter, collapsed suction hose, waxed fuel in cold weather).
Below specification = the pump is not doing work: worn vanes or gears, internal bypass, cavitation from a suction-side air leak, or low supply voltage.
A DSO current waveform showing one or more low humps in the commutation pattern indicates a shorted or open armature segment, exactly as it would on any other small DC motor.
2. Voltage drop under running load
As everywhere else in commercial electrical work, a static resistance check is useless here. Test under load with the pump running:
Insulated side: meter red lead on the battery positive post, black lead on the pump's positive terminal. Maximum about 0.5 V total, with no single connection over about 0.1 V.
Ground side: meter red lead on the pump's ground terminal, black lead on the battery negative post. Maximum about 0.2 V .
Across the relay contacts (30 to 87), energized: about 0.2 V maximum. Burned relay contacts are a frequent cause of a pump that runs slowly and delivers marginal pressure while the fuse and wiring test fine.
A pump losing 2 V to a corroded ground is turning far more slowly than the ECM intends, which shows up as low supply pressure, hard starting, and low-power complaints — and which is instantly cured by cleaning a stud rather than replacing a pump.
3. Command verification
Use the scan tool before the meter where possible. Most OEM software offers a fuel pump prime or fuel pump on/off bi-directional command . If the tool can run the pump and the pump runs, the relay, wiring, and motor are functional and the complaint is in the ECM's enable logic or its crankshaft speed input. If the tool commands the pump and nothing happens, you are in the circuit.
Confirming the Hydraulic Result
An electrical test alone never finishes this job. Confirm what the pump actually delivers:
Supply pressure at the test port ahead of the high-pressure pump, compared against specification, both at cranking and at idle.
Restriction (vacuum) on the suction side , measured between the tank and the pump. Excessive suction restriction indicates a plugged pre-filter, a collapsed pickup tube, or a blocked tank vent, and it will destroy a new pump as quickly as it destroyed the old one.
Flow volume into a graduated container over a timed interval where the OEM publishes a specification.
Air in the fuel. A clear section of line or a sight glass showing continuous bubbles means a suction-side leak upstream of the pump — every replacement pump will "fail" until that leak is found.
Tip
Always rule out the primary filter first. A restricted fuel filter/water separator simultaneously raises pump current and lowers delivered flow — the exact signature of a failing pump. Changing the filter costs minutes; changing a pump costs hours. Check the water-in-fuel sensor status (SPN 97) at the same time, and verify that any fuel-filter heater or heated water separator circuit is not shorted.
Tank-to-Tank Transfer Pump Systems
Commercial tractors with dual saddle tanks normally equalize through a crossover line, but vocational trucks, long-range vehicles, and units with auxiliary belly tanks often carry a separate electric transfer pump :
Manual control: a dash-mounted momentary or latching switch energizes a relay, which runs the transfer pump until the driver stops it. This design depends entirely on the driver and is the usual cause of fuel spilled from an overfilled tank.
Automatic control: float switches, reed-switch level senders, or the body controller start the pump when the receiving tank drops below a threshold and stop it when the source tank empties or the receiving tank fills.
Run-dry protection matters because these pumps are frequently positive-displacement designs that overheat quickly with no fuel passing through them. A low-level switch in the source tank, or a current-monitoring controller that detects the low-load signature of a dry pump, provides it.
Circuit specifics: transfer pumps are usually on their own fused feed and their own frame ground, and are often wired to an unswitched battery source so they can run with the key off. That makes them a legitimate suspect during a parasitic-draw investigation — a transfer pump relay with welded contacts or a shorted dash switch will drain a battery bank overnight and is easily found with the non-intrusive millivolt fuse-drop method.
Diagnostic Matrix
Complaint Probable Electrical/Fuel Cause Verification
Extended crank; starts after several key cycles Lost prime: pump flow low, drain-back through a check valve, suction-side air leak, or restricted filter Watch supply pressure during key-on prime; inspect for bubbles; replace filter
Pump runs at key-on then stops; engine will not start Normal prime timeout — the ECM never saw engine rotation Verify crankshaft speed signal and cranking rpm; this is not a pump fault
Pump never runs at key-on Blown fuse, open relay coil, failed ECM driver, open pump ground Command the pump with the scan tool; check for voltage and ground at the pump
Pump runs but supply pressure is low; high current Restricted filter, collapsed suction hose, dragging pump motor Suction restriction test; filter change; compare current to specification
Pump runs but supply pressure is low; low current Worn pump, internal bypass, cavitation, or low voltage at the pump Voltage drop test under load; flow test
Pump runs slowly; marginal pressure; wiring "tests good" Burned relay contacts or corroded frame ground behind the tank Voltage drop across relay 30-to-87 and on the ground side, under load
Battery bank dead after a weekend; transfer pump circuit warm Welded transfer pump relay contacts or shorted dash switch on an unswitched feed Non-intrusive millivolt drop across the transfer pump fuse