Study guide

2.3 Feature Control Frame Structure and Reading

ASME GDTP Senior Level Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009

2 Dimensioning and Symbology

2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases

3 Datum Referencing I: Selection and Precedence

3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators

4 Datum Referencing II: Modifiers and Shift

4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size

5 Datum Referencing III: Setup and Calculations

5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts

6 Form Controls

6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size

7 Orientation Controls

7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control

8 Location I: Position and Boundaries

8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC

9 Location II: Application and Modifiers

9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations

10 Location III: Patterns and Allocation

10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry

11 Profile I: Fundamentals and Strategy

11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition

12 Profile II: Scope and Verification

12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement

13 Runout Controls

13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form

14 Exam Strategy and Calculations

14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review

2.3 Feature Control Frame Structure and Reading

Key Takeaways Explain This Topic AI

A feature control frame (FCF) is read left to right: geometric characteristic symbol, tolerance zone description and value, material condition modifier (if any), then primary, secondary, and tertiary datum references.

Each compartment has a fixed meaning — the symbol identifies the control type, the tolerance compartment defines zone shape and size, and the datum compartments identify the DRF in precedence order.

A single-segment FCF controls one relationship to one DRF; a multi-segment (two or more rows) FCF provides additional, sometimes looser, controls such as pattern refinement or different datum references.

Composite FCFs (one symbol shared across segments) refine pattern location and orientation separately from the pattern-to-datum relationship; the senior exam tests the distinction between composite position and composite profile.

Omitting a datum compartment is intentional — some controls (form) never reference datums; others (profile of a surface) may optionally reference datums to control location/orientation in addition to form.

Last updated: August 2026

FCF Anatomy — Left to Right

A feature control frame is a rectangular box divided into compartments. Reading left to right: ┌──────┬──────────────┬───────┬───────┬───────┐

  • │ ⌖ │ Ø0.2 Ⓜ │ A │ B │ C │
  • └──────┴──────────────┴───────┴───────┴───────┘
  • (1) (2) (3) (4) (5)

Geometric characteristic symbol — the type of control (position, profile, flatness, etc.).

Tolerance zone — zone shape prefix (Ø for cylindrical, Ⓢ for spherical, no prefix for a width zone), tolerance value, and any material condition modifier (Ⓜ MMC, Ⓛ LMC; RFS is implied by default in 2009 and shown by no symbol).

Primary datum reference — the first datum in the DRF, the most constraining.

Secondary datum reference — constrains remaining degrees after the primary.

Tertiary datum reference — constrains the final degrees (typically location in one direction or clocking).

Each compartment has a fixed meaning; the order is not interchangeable. Swapping the primary and secondary datum changes the DRF and the inspection setup. A control written A|B|C is not equivalent to B|A|C .

Characteristic Symbol Catalog

Symbol Characteristic Type Datums required?

  • — Straightness Form No
  • ⏥ Flatness Form No
  • ○ Circularity (roundness) Form No
  • ⌭ Cylindricity Form No
  • ⌖ Position Location Yes
  • ⌘ Concentricity Location Yes (deprecated in 2018)
  • ⌭ (with feature) Symmetry Location Yes (deprecated in 2018)
  • ∠ Angularity Orientation Yes
  • ⊥ Perpendicularity Orientation Yes
  • // Parallelism Orientation Yes
  • ⌢ Profile of a line Profile Optional
  • ⌭ (profile) Profile of a surface Profile Optional
  • ↗ Circular runout Runout Yes
  • ↗↗ Total runout Runout Yes

Form characteristics (straightness, flatness, circularity, cylindricity) never reference datums — a form FCF with a datum reference is malformed. Profile of a line/surface may reference datums optionally: without datums, profile controls only form (the shape of the true profile); with datums, profile controls orientation and/or location to the DRF. This optional-datum rule is a frequent Senior question.

Reading an FCF Aloud

A useful Senior technique is to verbalize the FCF in plain language:

⌖ | Ø0.2 Ⓜ | A | B | C reads as: The axis of the feature must lie within a Ø0.2 cylindrical tolerance zone at maximum material condition, the zone oriented and located relative to primary datum A, secondary datum B, and tertiary datum C.

⌢ | 0.3 | A reads as: The surface must lie within a 0.3-wide zone bounded by two parallel surfaces 0.3 apart, centered on the true profile, oriented to datum A.

// | 0.05 | A reads as: The surface must lie between two parallel planes 0.05 apart, parallel to primary datum A.

Single-Segment vs Multi-Segment vs Composite

A single-segment FCF has one row of compartments and controls one relationship to one DRF. A multi-segment FCF stacks two or more independent single-segment rows (each with its own symbol) when two different controls apply to the same feature — for example, a position control and a perpendicularity control on the same hole.

A composite FCF shares a single characteristic symbol across multiple segments (rows). Composite position is the common case: ┌──────┬──────────┬─────┬─────┬─────┐

  • │ ⌖ │ Ø0.4 Ⓜ│ A │ B │ C │
  • ├──────┼──────────┼─────┼─────┼─────┤
  • │ ⌖ │ Ø0.1 Ⓜ│ A │ │ │
  • └──────┴──────────┴─────┴─────┴─────┘

The upper segment (Pattern-Refining Feature Control, PLTZF) locates the pattern to the DRF: Ø0.4 at MMC to A|B|C.

The lower segment (Feature-Relating, FRTZF) refines the pattern internally: Ø0.1 at MMC, oriented to A only. The lower segment controls hole-to-hole location within the pattern, not pattern-to-datum location.

Composite profile works similarly: the upper segment controls profile to the full DRF, the lower segment refines the profile's form and orientation to a subset of datums. The Senior exam tests the rule that composite segments share the symbol and the lower segment cannot have a larger tolerance than the upper . A lower segment datum reference must be a subset (in order) of the upper segment datums.

Reading Order and What Each Compartment Decides

The symbol decides the characteristic and whether datums are allowed.

The tolerance compartment decides zone shape (prefix), size (value), and material condition (modifier).

The datum compartments decide which surfaces simulate the DRF and in what precedence.

The boundary modifiers on datum references (Ⓜ/Ⓛ or implied RMB) decide whether each datum feature is referenced at MMB, LMB, or RMB.

Missing compartments carry meaning. An FCF with no tertiary datum leaves one rotational degree of freedom unconstrained; an FCF with no datum compartments at all (for profile of a surface) controls only the form of the true profile, not its location.

Common FCF Reading Errors at the Senior Level

The Senior exam rewards candidates who read the FCF literally rather than assuming design intent. Three reading errors appear repeatedly. First , confusing the tolerance compartment's prefix with the zone shape: a position control written without the diameter symbol is a width zone (two parallel planes) applied to a center plane, not a cylindrical zone. A position callout of 0.2 (no Ø) on a slot is a width zone on the slot's center plane; reading it as a cylinder reverses the geometry and the acceptance boundary. Second , misreading a datum modifier as a tolerance modifier: the symbol Ⓜ in the tolerance compartment applies bonus tolerance to the controlled feature, while the same symbol Ⓜ in a datum compartment permits datum shift between the datum feature and its simulator. These are two different effects that share one glyph, and a candidate who conflates them will miscalculate both the acceptance boundary and the functional gage. Third , assuming a multi-segment frame is always composite: two stacked single-segment frames, each carrying its own characteristic symbol, are independent controls that both fully apply; a composite frame shares one symbol across its segments, and the lower segment only refines orientation or pattern location without re-locating to the datums. Reading the symbol placement and the segment sharing correctly is what distinguishes these cases.

Datum Modifiers in the Datum Compartments

A datum reference may carry its own material condition modifier (Ⓜ or Ⓛ) in Y14.5-2009, applied to the datum feature simulator rather than to the controlled feature. A datum referenced at MMB, written for example as AⓂ , can permit datum mobility as the datum feature departs from that fixed boundary — this is datum shift , a freedom of the datum reference frame itself, not bonus tolerance on the controlled feature. Datum shift is especially common in composite position frames and on patterns located to a datum feature of size. The Senior distinction is precise: bonus tolerance grows the controlled feature's tolerance zone as the feature departs from its material condition; datum shift moves the entire DRF relative to the part as the datum feature departs. They are independent mechanisms, and a candidate who treats datum shift as bonus will mis-state the gage design and the worst-case acceptance boundary. When no modifier is shown on a datum-feature reference in Y14.5-2009, RMB is the default. Keep this datum-side terminology distinct from RFS on the toleranced feature.