Study guide
1.2 Senior Level vs Technologist and Y14.5 Revisions
ASME GDTP Senior Level Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009
2 Dimensioning and Symbology
2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases
3 Datum Referencing I: Selection and Precedence
3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators
4 Datum Referencing II: Modifiers and Shift
4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size
5 Datum Referencing III: Setup and Calculations
5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts
6 Form Controls
6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size
7 Orientation Controls
7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control
8 Location I: Position and Boundaries
8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC
9 Location II: Application and Modifiers
9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations
10 Location III: Patterns and Allocation
10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry
11 Profile I: Fundamentals and Strategy
11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition
12 Profile II: Scope and Verification
12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement
13 Runout Controls
13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form
14 Exam Strategy and Calculations
14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review
1.2 Senior Level vs Technologist and Y14.5 Revisions
Key Takeaways Explain This Topic AI
Senior measures selecting and applying geometric controls (design authority); Technologist measures interpreting GD&T specifications on drawings.
Senior requires a minimum of 3 years of relevant GD&T professional experience; the Technologist level has no experience requirement, and Technologist certification is NOT a prerequisite for Senior.
ASME currently bases Senior certification on Y14.5-2009 or Y14.5-2018; the legacy Y14.5M-1994 exam is available only on request through ASME Customer Care.
Y14.5-2018 Senior passes at 74% overall for $495, while this guide's Y14.5-2009 Senior exam passes at 78% for $623; both require a minimum of 3 years of relevant experience.
Passing one revision does NOT certify you in another — each revision is an independent credential named on the certificate.
Last updated: August 2026
Senior vs Technologist, and the 1994 / 2009 / 2018 Revisions
Quick Answer: ASME runs two GDTP tiers — Senior (selects and applies controls; design authority) and Technologist (interprets drawings). ASME currently offers Senior certification based on Y14.5-2009 or Y14.5-2018; the legacy Y14.5M-1994 exam remains available only on request. Each revision is a separate credential. Passing one revision does not certify you in another.
ASME's GDTP family is shaped like a ladder, but you do not have to climb it rung by rung . The two tiers measure different competencies, and the two current certification bases have separate exams. Choosing the right combination before you apply saves money and months of preparation.
Senior vs Technologist — What Each Measures
Dimension Senior Technologist
Competency Selecting geometric controls based on feature function and relationships Reading and interpreting GD&T specifications on drawings
Authority Design authority — applies GD&T to drawings, tooling, gaging Interpretation authority — verifies conformance to existing specs
Core tasks Selecting controls, performing tolerance calculations, applying symbols/modifiers/datum references, applying GD&T to manufacturing/quality/verification, establishing functional gaging Interpreting controls others have specified
Experience Minimum 3 years of relevant GD&T professional experience None — the Technologist exam has no experience requirement
Prerequisite Technologist certification NOT required None to sit Technologist
The Senior is the heavier lift because selecting a control is harder than reading one. A Senior candidate must decide, given a feature's function, whether to use position, profile, runout, or a simpler plus-minus tolerance — and then defend the choice functionally and economically. That is design authority. A Technologist, by contrast, receives a drawing that already specifies those controls and must correctly interpret what the drawing requires, including reading boundaries, zones, and modifiers, without necessarily choosing them.
Current Certification Bases and the Legacy 1994 Exam
ASME currently bases certification on Y14.5-2009 or Y14.5-2018. The older Y14.5M-1994 exam remains available only by request through ASME Customer Care. Each exam produces a revision-specific credential, so passing one revision does not certify you in another .
- Item 1994 Senior 2009 Senior 2018 Senior
- Questions 150 multiple-choice 150 multiple-choice 150 multiple-choice
- Time 6 hours 6 hours 6 hours
- Format Closed book Closed book Closed book
- Passing overall 80% 78% 74%
- Per-category minimum 50% per section 50% each of 7 categories 50% per section
- Application/exam fee Retest only, $413 $623 $495
- Retest fee $413 $413 $325
- Experience required Minimum 3 years Minimum 3 years Minimum 3 years
- Status Available on request through ASME Customer Care Currently offered Currently offered
The experience requirement is not a differentiator between the two current bases — ASME's current handbook sets a minimum of 3 years for Senior applicants. What still differs is the pass mark and the fee. The 2018 Senior is the newest and cheapest path at a 74% pass mark and $495. The 2009 Senior costs $623 and passes at 78%, but remains the revision with the most widely circulated practice material and the most drawings in service, which is why this guide teaches it. The 1994 Senior passes at 80% and uses an entirely different section split — 10% on Technologist-level topics, 20% on Datum Selection, 40% on General Tolerancing, Tolerance Calculation and Appendices, 15% on Application of Modifiers in Feature Control Frames, and 15% on Composite Positional Tolerancing. It is available on request through ASME Customer Care; few candidates choose it today.
What Changed Between 2009 and 2018
The 2018 revision is not a wholesale rewrite, but it both added and deleted content the other exam does not test. It deleted concentricity and symmetry outright, added the dynamic profile modifier and the from-to symbol, restored the term true geometric counterpart in place of 2009's datum feature simulator (theoretical), renamed multiple datum features to common datum features , and replaced the candidate datum set with a single default stabilized solution . Section 1.4 works through each of these. If you study with 2009 materials and then sit the 2018 exam, expect questions on symbols you have not seen and on two controls you were taught that no longer exist. Match your study revision to your exam revision.
Choosing the Right Revision
Pick the revision that matches your employer's drawings, your training materials, and your career horizon :
Pick 2018 if your organization has migrated to Y14.5-2018, you want the newest credential, and you want the lowest pass mark (74%) and fee ($495). The 2018 standard adds the dynamic profile modifier, deletes concentricity and symmetry, and revises several terms; the exam tests the updated language.
Pick 2009 if your drawings and training are Y14.5-2009-based, your practice bank is the 2009 bank, or your employer still specifies Y14.5-2009. This is the most common choice and the path this guide supports.
Request 1994 only if your organization has a specific legacy need and ASME Customer Care confirms availability.
What "Passing One Revision Does Not Certify Another" Means
A Senior certificate names the revision you passed. If you pass Y14.5-2009 Senior, you are not certified as Y14.5-2018 Senior. To hold both, you must apply for and pass both exams separately. Likewise, holding Technologist does not grant Senior; the two are independent credentials. Plan your path once, then apply with confidence.
Revision Overlap You Can Exploit
The underlying geometry does not change between revisions — a datum is still a datum, position is still position. Most of what you study for 2009 Senior (datum referencing, position, profile, runout) transfers to 2018. The differences are in symbol sets, modifier names, and a few new controls. If you prepare well for 2009 Senior and later need 2018, expect a focused delta course rather than a full re-study. That overlap is also why a 2009-focused guide remains useful even to candidates who eventually add the 2018 credential.