Study guide
8.1 Position Tolerancing and True Position
ASME GDTP Senior Level Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009
2 Dimensioning and Symbology
2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases
3 Datum Referencing I: Selection and Precedence
3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators
4 Datum Referencing II: Modifiers and Shift
4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size
5 Datum Referencing III: Setup and Calculations
5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts
6 Form Controls
6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size
7 Orientation Controls
7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control
8 Location I: Position and Boundaries
8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC
9 Location II: Application and Modifiers
9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations
10 Location III: Patterns and Allocation
10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry
11 Profile I: Fundamentals and Strategy
11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition
12 Profile II: Scope and Verification
12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement
13 Runout Controls
13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form
14 Exam Strategy and Calculations
14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review
8.1 Position Tolerancing and True Position
Key Takeaways Explain This Topic AI
Position tolerancing locates a feature of size relative to a datum reference frame using a theoretically exact true position defined by basic dimensions; the basic dimensions themselves carry no plus/minus tolerance.
The position tolerance zone is cylindrical (with a diameter symbol) for a hole or pin axis, and two parallel planes for a slot or tab; the zone is centered on true position.
Implied 90-degree basic angles exist between features explicitly dimensioned and any datum axes/planes when shown at 90 degrees on the drawing, even with no basic angle callout.
Material condition modifiers (RFS, MMC, LMC) on the position feature control frame change whether bonus tolerance is available and how the gaging boundary is defined.
Position over coordinate tolerancing gives a round acceptance zone instead of a square one, eliminates double-dipping of tolerance, and decouples location from size via Rule #1.
Last updated: August 2026
8.1 Position Tolerancing and True Position
Position tolerancing (ASME Y14.5-2009 Section 7) is the geometric control that locates a feature of size relative to a datum reference frame (DRF) . It is the workhorse of location control and the most heavily tested topic on the Senior exam because it ties together datums, material condition modifiers, virtual condition, and bonus tolerance.
True Position: The Theoretically Exact Location
True position is the theoretically exact location of a feature, defined by basic dimensions (boxed dimensions shown on the drawing). Basic dimensions carry no plus/minus tolerance of their own; they only define where the ideal feature sits. All permissible variation is delivered through the position tolerance zone called out in the feature control frame (FCF).
A feature control frame for position reads, left to right:
- Frame Symbol Tolerance Material Modifier Datum A Datum B Datum C
- Example ⌖ Ø0.2 Ⓜ A B C
This FCF means: "The axis of the feature shall be contained within a cylindrical zone of diameter 0.2 at MMC, located by basic dimensions relative to datum A (primary), B (secondary), and C (tertiary)."
The Position Tolerance Zone
The shape of the zone depends on the feature:
Cylindrical zone (with the diameter symbol ⌀ in the FCF) — applied to the axis of a hole, pin, or cylinder. The produced axis must lie inside a cylinder of the tolerance diameter, centered on true position.
Two parallel planes (no diameter symbol) — applied to the center plane of a slot, tab, keyseat, or wide feature of size. The produced center plane must lie between two parallel planes separated by the tolerance value, symmetric about true position.
For a hole at MMC with a cylindrical zone, the zone diameter is the stated tolerance. As the hole departs from MMC toward LMC, bonus tolerance (Section 8.3) expands the zone diameter.
Implied 90-Degree Basic Relationships
When a drawing shows a center line, axis, or surface of a feature at 90 degrees to a datum axis or plane and no basic angle is dimensioned, a 90-degree basic angle is implied . This implied basic angle still has to be respected — position tolerance zones are centered on true position, which depends on those implied basics. Senior exam items often hide an implied 90-degree relationship inside a pattern location problem and expect you to know it is basic, not free.
RFS vs. MMC vs. LMC on the Position Control
The material condition modifier in the position FCF (after the tolerance value) determines how size variation interacts with position:
Modifier Symbol Effect
RFS (regardless of feature size) No material condition symbol (default in both 2009 and 2018) Tolerance zone is fixed at the stated value regardless of actual feature size. No bonus.
MMC Ⓜ Bonus tolerance is added as the feature departs from MMC toward LMC. Virtual condition is the mating/gaging boundary.
LMC Ⓛ Bonus tolerance is added as the feature departs from LMC toward MMC. Resultant/wall-thickness boundary is fixed.
In ASME Y14.5-2009, RFS is the default when no material condition modifier is shown ; Y14.5-2018 retains that same controlled-feature default. RMB/MMB/LMB are datum-feature-reference terms, not a replacement for RFS/MMC/LMC. On the Senior exam, the modifier is almost always given explicitly because the virtual-condition and bonus calculations depend on it.
Position vs. Coordinate (Plus/Minus) Tolerancing
Consider locating a hole with coordinate tolerancing of ±0.2 in X and ±0.2 in Y. The produced center can land anywhere in a 0.4 × 0.4 square — a diagonal displacement of up to √(0.4² + 0.4²) ≈ 0.566 from true position, yet a hole exactly on the X or Y boundary (0.2 off) is only 0.2 off. Coordinate tolerancing gives a non-uniform zone: more tolerance along the diagonal than along the axes.
Position tolerancing with ⌀0.4 gives a circular zone of radius 0.2 — uniform in every direction — and the worst-case displacement is exactly 0.2 in every direction. For a mating pin/hole this uniform zone is what the mating part actually cares about (radial clearance). Position also decouples location (in the FCF) from size (in the size tolerance) instead of double-counting the size tolerance inside a ± location stack.
Worked Example: Four-Hole Pattern
A plate has a 4-hole pattern on a 50 × 50 basic bolt circle, each hole ⌀10.0 ± 0.2, with position ⌀0.3 at MMC to datums A | B | C.
The basic 50 × 50 dimensions define true position of each hole center — they have no tolerance.
Each hole's axis must lie inside a cylinder of ⌀0.3 centered on its true position , at MMC (hole at 9.8).
At MMC (9.8), bonus = 0, so the zone is ⌀0.3.
If a hole is produced at 10.0 (0.2 away from MMC), bonus = 0.2, so the effective zone = ⌀0.3 + 0.2 = ⌀0.5 .
If a hole is produced at LMC (10.2), bonus = 0.4, so the effective zone = ⌀0.3 + 0.4 = ⌀0.7 .
The datum reference frame for the pattern is A (the primary planar datum — the plate's bottom face, constraining 2 rotational DOF), B and C (the two edges, constraining the remaining DOF). Each hole is located identically relative to the DRF; the pattern is simultaneously located to the same DRF, so a pattern-location error (the whole pattern shifted) is judged once against the DRF, not hole-to-hole.