Study guide

10.2 Patterns, Simultaneous Requirements, and Multiple Segments

ASME GDTP Senior Level Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009

2 Dimensioning and Symbology

2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases

3 Datum Referencing I: Selection and Precedence

3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators

4 Datum Referencing II: Modifiers and Shift

4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size

5 Datum Referencing III: Setup and Calculations

5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts

6 Form Controls

6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size

7 Orientation Controls

7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control

8 Location I: Position and Boundaries

8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC

9 Location II: Application and Modifiers

9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations

10 Location III: Patterns and Allocation

10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry

11 Profile I: Fundamentals and Strategy

11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition

12 Profile II: Scope and Verification

12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement

13 Runout Controls

13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form

14 Exam Strategy and Calculations

14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review

10.2 Patterns, Simultaneous Requirements, and Multiple Segments

Key Takeaways Explain This Topic AI

The simultaneous requirements rule states that two or more features located by the SAME datum reference frame (same datums, same order, same modifiers) are inspected as one simultaneous requirement — a single setup verifies all of them together.

If datum references differ in feature, precedence, or material-boundary modifier, the requirements are separate by construction; the notation SEP REQT is used to override simultaneity that would otherwise arise from a common datum reference frame.

Separate single-segment position or profile callouts that locate features from the same datum reference frame are simultaneous by default; having separate geometric symbols does not by itself make them separate.

A common trap is assuming features are simultaneous when they repeat datum letters but differ in datum boundary (for example, B at MMB in one frame and B at RMB in another); the boundary difference creates different datum reference frames.

Use the exact notes SIM REQT and SEP REQT: SIM REQT explicitly groups otherwise separate but compatible requirements, while SEP REQT separates requirements that would otherwise be simultaneous.

Last updated: August 2026

10.2 Patterns, Simultaneous Requirements, and Multiple Segments

Quick Answer: Applicable position and profile requirements that locate features or patterns from the same datum reference frame are simultaneous by default in Y14.5-2009. They must all be satisfied from one permissible datum setup. Different datum references create separate requirements. Use SEP REQT to override default simultaneity and SIM REQT to explicitly group otherwise separate, compatible requirements.

What simultaneous means

Two patterns controlled by separate position frames can still be one simultaneous requirement. If both reference A|B|C in the same order and at the same datum material boundaries, the applicable zones must be satisfied together from one realization of that DRF. This matters whenever datum mobility is available: the part cannot use one allowed shift to pass the first pattern and a different shift to pass the second.

The word simultaneous describes the geometric requirement, not a mandate that every point be probed at the same instant. A CMM may measure features sequentially while holding one datum alignment. What is prohibited is independently optimizing or re-establishing the DRF for each member of the simultaneous group.

Default separate cases

Requirements are separate when their datum reference frames differ, including:

  • different datum features, such as A|B|C versus A|D|C ;
  • different precedence, such as A|B|C versus A|C|B ;
  • different material-boundary modifiers on a datum reference; or

a different set of referenced datums, such as A|B|C versus A|B .

Those frames permit different setup logic, so simultaneity cannot simply be inferred from repeated datum letters.

The two exact notes

SEP REQT means separate requirement. It is placed with requirements that would otherwise be simultaneous so each may use its own permissible realization of the datum reference frame.

SIM REQT means simultaneous requirement. It explicitly groups requirements that would otherwise be separate, but only where the drawing defines a coherent common setup. The note is not a license to erase contradictory datum precedence or incompatible simulators.

Use the spaces and spelling exactly as shown: SEP REQT and SIM REQT .

Composite and multiple single-segment controls

A composite feature control frame is one structured control with an upper pattern-locating segment and a lower feature-relating segment. Its segments have defined hierarchical roles: the upper segment locates the pattern to its referenced DRF, while the lower segment refines feature-to-feature relationship and any repeated datum-controlled orientation.

Multiple single-segment feature control frames are not composite merely because they are stacked or applied to the same feature. Each frame states a complete control. If separate single-segment requirements locate different features or patterns from the same DRF, however, the simultaneous-requirement rule still applies by default. Separate symbols do not create an automatic exception. Nor does SEP REQT transform the segments of a composite frame into independent controls; a designer who needs different controls must specify the appropriate separate frames.

Worked example — two bolt circles

A flange has an outer 8-hole pattern and an inner 4-hole pattern. Each has its own position feature control frame, and both reference A|B|C with the same datum boundaries. The two patterns are simultaneous by default. One datum setup must allow all 12 feature axes to satisfy their respective zones.

If the designer adds SEP REQT to make the two pattern requirements separate, each pattern may be evaluated with its own permissible DRF realization. If one pattern instead references B at MMB and the other references B at RMB, they are already separate because the datum reference frames differ; a SEP REQT note is unnecessary.

Decision table

Specification Default Correct treatment

Separate position/profile FCFs; same datums, order, and boundaries Simultaneous One permissible DRF realization satisfies all; use SEP REQT only to separate

Different datum feature, order, set, or boundary Separate Evaluate each requirement from its stated DRF

Multiple single-segment FCFs locating features from the same DRF Simultaneous where the rule applies Separate symbols alone do not cancel simultaneity

Composite FCF Structured composite control Interpret upper and lower segments by their defined roles; notes do not convert its structure

Otherwise separate but compatible requirements explicitly grouped Simultaneous by note Use the exact notation SIM REQT and ensure a coherent common setup

Senior-level checks

Compare the full datum reference: letters, order, omitted datums, and modifiers.

Do not confuse a common DRF with separate inspection optimization.

Spell the notes exactly: SEP REQT and SIM REQT .

Do not assume multiple single-segment frames are separate by default.

Do not use a note to paper over incompatible datum schemes.