Study guide

11.3 Datum-Referenced Profile Strategy

ASME GDTP Senior Level Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009

2 Dimensioning and Symbology

2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases

3 Datum Referencing I: Selection and Precedence

3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators

4 Datum Referencing II: Modifiers and Shift

4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size

5 Datum Referencing III: Setup and Calculations

5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts

6 Form Controls

6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size

7 Orientation Controls

7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control

8 Location I: Position and Boundaries

8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC

9 Location II: Application and Modifiers

9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations

10 Location III: Patterns and Allocation

10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry

11 Profile I: Fundamentals and Strategy

11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition

12 Profile II: Scope and Verification

12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement

13 Runout Controls

13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form

14 Exam Strategy and Calculations

14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review

11.3 Datum-Referenced Profile Strategy

Key Takeaways Explain This Topic AI

Profile is unique in that adding datums progressively adds control: no datum = form only, one datum = form + orientation, two or three datums = form + orientation + location.

The datum reference frame orients and locates the profile tolerance zone; the true profile is positioned at basic dimensions from the DRF and the zone follows it.

For contoured features, profile with datums is the correct analog of position; position itself cannot control a contoured surface because position is defined for axes, center planes, and width features.

Choosing datums for a profile-controlled surface follows the same functional-datum logic as other controls: the datum scheme must reflect how the feature is located and oriented in assembly.

A single profile-of-a-surface callout referencing two or three datums can replace what would otherwise require separate orientation and location callouts on a contoured feature.

Last updated: August 2026

11.3 Datum-Referenced Profile Strategy

Quick Answer: Profile is the only Y14.5-2009 characteristic whose scope expands with each added datum: no datum controls form, one datum adds orientation, two or three datums add location. The datum reference frame (DRF) orients and locates the profile zone, and for any contoured feature profile with datums is the correct replacement for position.

Progressive control through datum reference

The defining strategy of profile is that the same callout controls more as more datums are referenced . This is not a side effect — it is how the standard defines profile. Y14.5-2009 expresses this by tying the degrees of freedom constrained to the number of datums in the DRF:

  • Datums referenced What the profile callout controls Contoured analog of
  • None Form only (shape of the contour) Flatness / cylindricity
  • One Form + orientation to that datum Perpendicularity / angularity / parallelism
  • Two Form + orientation + location in two degrees of freedom Position (partial)
  • Three (full DRF) Form + orientation + location (full) Position (full)

A critical Senior-level point: this is cumulative . With two datums referenced, the callout controls form, orientation, and location simultaneously — not three separate things. There is one zone, oriented and located by the DRF.

How the DRF orients and locates the zone

The true profile is positioned at basic dimensions from the DRF. The DRF establishes the orientation and location of the true profile, and the tolerance zone (a uniform boundary disposed about the true profile) inherits that orientation and location. The actual surface must lie within the zone. So the DRF does two things:

Orients the true profile (and therefore the zone) by locking the angular degrees of freedom referenced.

Locates the true profile (and therefore the zone) by establishing the basic dimensions from which the true profile is offset.

Because the zone is constructed from the true profile and the true profile is located by basic dimensions from the DRF, the location tolerance is the profile tolerance itself — not a separate positional tolerance. There is no separate "position" of the contour; the profile zone IS the location zone.

Profile vs position for contoured features

Position tolerance in Y14.5-2009 is defined for features of size: axes of cylinders, center planes of width features, and (in some applications) surfaces of features of size. A contoured surface that is not a feature of size has no axis and no center plane, so position cannot control it. Profile of a surface with two or three datums is the correct analog:

Position controls the location of an axis or center plane within a cylindrical or parallel-plane zone.

Profile of a surface controls the location of a contoured surface within a uniform boundary disposed about the true profile.

A Senior item may show a contoured mating face with a position callout and ask what is wrong. The answer is that position is the wrong characteristic for a contoured surface that is not a feature of size; profile of a surface with the appropriate datums is correct.

Choosing datums for a profile-controlled surface

Datum selection for profile follows the same functional logic as for any other control:

Primary datum is the surface that establishes the most important orientation — typically the mating face that locates the part in assembly.

Secondary datum adds the next most important orientation and a degree of location — often a locating edge or bore.

Tertiary datum completes the DRF, fully constraining the part and the true profile's location.

For a contoured face on a cast housing, for example, the primary datum might be the planar mounting pad (orienting the contour), the secondary the bore axis (locating the contour radially), and the tertiary a locator pin (clocking the contour). The profile callout references A | B | C and the contour is at basic dimensions from that DRF.

Worked example: contoured sealing face

A pump housing has a contoured sealing face that mates with a flexible diaphragm. The face must be oriented to the mounting flange and located relative to the pump bore.

Datum A: the mounting flange face (primary, orients the contour).

Datum B: the pump bore axis (secondary, locates the contour radially).

Datum C: a clocking dowel (tertiary, fixes rotation about the bore).

The contour is defined by basic dimensions from the A | B | C DRF.

The callout: profile of a surface 0.4 | A | B | C.

What does this single callout control?

Form : the produced contour's shape must match the true profile within 0.4.

Orientation : the contour must be oriented to the flange face A (analogous to perpendicularity of the contour to A).

Location : the contour must sit at the basic dimensions from the B | C DRF (analogous to position of the contour).

A part that has perfect form but is tilted relative to A fails. A part that has perfect form and orientation but is shifted radially from B fails. A part within the 0.4-wide zone oriented and located by A | B | C passes. The single profile callout does the work of three separate controls.

Composite and multiple-segment profile frames

A more advanced strategy (covered in detail in Chapter 12) is the composite profile control frame, where the upper segment locates the contour relative to the DRF and the lower segment refines orientation or form with a smaller tolerance. For now, recognize that the upper segment's datums always establish location, while the lower segment may reference the same datums (refining form/orientation) or a subset.

  • Senior-level traps
  • Trap 1: assuming profile needs a separate position callout

Because profile with two or three datums controls location, a separate position callout on the same contoured feature is redundant and often contradictory. The profile zone already constrains location.

Trap 2: misreading a one-datum profile as a location control

Profile with only one datum references controls form and orientation, not location. If a question asks what a profile callout with only datum A controls, location is not in the answer.

Trap 3: applying position to a non-feature-of-size contour

Position cannot control a contoured surface that is not a feature of size. The correct callout is profile of a surface with appropriate datums.

Trap 4: forgetting cumulative control

With two datums, profile controls form + orientation + location simultaneously through one zone — not three independent tolerances. The 0.4-wide zone IS the orientation and location tolerance; there is no separate 0.4 for orientation and another 0.4 for location.

Control-level summary

  • Callout form Controls Typical use
  • Profile 0.2 (no datum) Form only Pure shape of a contour
  • Profile 0.2 | A Form + orientation to A Contour must be angled/oriented to A
  • Profile 0.2 | A | B Form + orientation + partial location Contour oriented to A, located to B in one direction
  • Profile 0.2 | A | B | C Form + orientation + full location Full DRF; contour fully located and oriented