Study guide
13.3 Runout vs Position, Profile, and Form
ASME GDTP Senior Level Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Senior Level vs Technologist and Y14.5 Revisions 1.3 How to Use This Guide and Study Strategy 1.4 The Y14.5-2018 Senior Exam and What Changed from 2009
2 Dimensioning and Symbology
2.1 Y14.5 Dimensioning Rules, Limits, and Fits 2.2 Basic Dimensions and Their Role 2.3 Feature Control Frame Structure and Reading 2.4 GD&T Symbols, Modifiers, and Communication 2.5 Screw Threads, Gears, and Splines 2.6 Angular Surfaces, Tapers, Radii, and Special Tolerance Cases
3 Datum Referencing I: Selection and Precedence
3.1 Functional Datum Feature Selection 3.2 Datum Precedence and Degrees of Freedom 3.3 Datum Targets 3.4 Datum Feature Simulators
4 Datum Referencing II: Modifiers and Shift
4.1 Multiple Datum Features and Datum Reference Frames 4.2 RMB, MMB, and LMB on Datum Features 4.3 Datum Shift Behavior 4.4 Planar vs Datum Feature of Size
5 Datum Referencing III: Setup and Calculations
5.1 Inclined and Translated Datum Features 5.2 Inspection Setup and Datum Establishment 5.3 Datum Calculation Walkthrough 5.4 Customized Datum Reference Frames and Rotational Constraint 5.5 Free State, Restrained Condition, and Nonrigid Parts
6 Form Controls
6.1 Flatness and Straightness 6.2 Circularity and Cylindricity 6.3 Rule #1, Form, and Size
7 Orientation Controls
7.1 Parallelism, Perpendicularity, and Angularity 7.2 Orientation Zones and Material Modifiers 7.3 Avoiding Unnecessary Orientation and Over-Control
8 Location I: Position and Boundaries
8.1 Position Tolerancing and True Position 8.2 Virtual and Resultant Condition 8.3 Bonus Tolerance at MMC and LMC
9 Location II: Application and Modifiers
9.1 Selecting MMC, LMC, and RFS by Function 9.2 Fixed and Floating Fastener Formulas 9.3 Projected Tolerance Zones 9.4 Coordinate Conversion and Appendix B Position Calculations
10 Location III: Patterns and Allocation
10.1 Composite Position Tolerancing 10.2 Patterns, Simultaneous Requirements, and Multiple Segments 10.3 Slots, Tabs, and Tolerance Allocation 10.4 Coaxial Feature Controls, Concentricity, and Symmetry
11 Profile I: Fundamentals and Strategy
11.1 Profile of Line and Surface 11.2 Defining the True Profile 11.3 Datum-Referenced Profile Strategy 11.4 Equal and Unequal Disposition
12 Profile II: Scope and Verification
12.1 All-Around, All-Over, and Limited Scope 12.2 Composite Profile and Coplanarity 12.3 Castings, Weldments, Sheet Metal, and CMM Evaluation 12.4 Combined Controls and Profile as a Refinement
13 Runout Controls
13.1 Circular and Total Runout 13.2 Datum-Axis Simulation and Rotating Parts 13.3 Runout vs Position, Profile, and Form
14 Exam Strategy and Calculations
14.1 Virtual/Resultant Condition and Bonus Formulas 14.2 Datum Shift and Worst-Case Boundary Calculations 14.3 Functional Gaging and Verification 14.4 Test-Day Tactics, Common Traps, and Review
13.3 Runout vs Position, Profile, and Form
Key Takeaways Explain This Topic AI
Runout controls indicated surface variation relative to a datum axis; position controls a derived axis or center plane; profile controls a surface relative to true profile; form controls shape without a datum.
Runout is often economical for rotating cylindrical surfaces because one reading combines surface form effects with relationship to the datum axis.
Runout may also control a face perpendicular to a datum axis; circular face runout limits wobble by circular element, while total face runout controls the whole face.
Choose perpendicularity for a pure face-orientation requirement, and choose face runout when rotation and indicator variation are the functional concern.
For this Y14.5-2009 guide, two journals acting together are described as multiple datum features establishing one datum A, not as an ordered two-datum sequence.
Last updated: August 2026
13.3 Runout vs Position, Profile, and Form
Quick Answer: Select the control from what function must be protected. Runout limits indicator variation of a surface during rotation about a datum axis. Position locates a derived axis or center plane. Profile controls a surface relative to true profile. Form controls shape without a datum.
What Each Control Constrains
Runout is datum-axis related and acts on the indicated surface. Its result combines applicable surface-form error with the surface's relationship to the datum axis.
Position constrains the derived axis or center plane of a feature of size in a basically located zone; it does not directly control every surface point.
Profile constrains surface points relative to true profile and can combine form, orientation, location, and sometimes size effects.
Form controls a feature's shape without locating or orienting it to a datum.
Cylindrical and Face Applications
For a bearing journal, seal diameter, or pulley surface that must run true to an assembly axis, runout directly matches the rotational function. Circular runout checks individual sections; total runout traverses the entire cylindrical surface and adds longitudinal form control.
A flat shoulder face perpendicular to the datum axis is also a valid runout application. Circular face runout limits wobble at each circular element. Total face runout evaluates the full face during rotation and radial traverse. If the only requirement is abstract orientation, perpendicularity is usually clearer; if operational wobble during rotation is the concern, face runout may be the direct functional control.
Decision Table
- Functional requirement Usually choose Why
- Cylindrical surface must run true to datum axis Runout Direct indicator-based composite surface requirement
Face wobble during rotation must be limited Circular or total face runout Validly relates the face to the datum axis
Face needs only orientation to an axis Perpendicularity States pure orientation without a rotational composite reading
- Feature axis must locate for assembly Position Controls the derived axis or center plane
- Complex contour must match true geometry Profile Controls surface points relative to true profile
- Shape alone matters and no datum relationship is needed Form Datum-free control
- Worked Scenario
A shaft's two bearing journals are identified as multiple datum features that jointly establish datum A. A finished cylindrical hub surface must run true to the bearing axis and must not taper along its width. Total runout of the hub surface to A is the direct choice: both journals establish the datum axis together, and the indicator traverses the full hub surface while the part rotates.
Position of the hub's derived axis would locate the axis but would not directly limit all surface form. Cylindricity would control form but would not relate the hub to datum A. Profile could express a surface relationship, but total runout is the purpose-built rotational control for this simple cylindrical function.
For an involute gear-tooth flank, by contrast, profile is appropriate because the controlled surface follows a defined noncircular true contour. The decision turns on the actual controlled surface and function, not merely on whether the overall part rotates.
Senior Traps
Saying every flat-face runout callout is invalid. Face runout is expressly possible.
Applying runout without a datum reference that establishes an axis.
Choosing position when the requirement includes surface form during rotation.
Choosing form when relationship to the datum axis also matters.
Treating two multiple datum features as an ordered A|B datum sequence.