Study guide

5.3 Demagnetization Procedures and Residual Field Limits

ASNT NDT Level II Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Certification Paths: SNT-TC-1A, CP-189, and ASNT Central Certification 1.3 Level I vs Level II vs Level III Responsibilities 1.4 Application, Scheduling, Identification, and Retake Rules

2 Eligibility, Fees & Recertification

2.1 Training Hours, Experience Days, and Documentation 2.2 Vision, Practical Exams, and the Employer's Written Practice 2.3 Fees, Validity, Recertification, and 529 Funding

3 NDT Fundamentals & Method Selection

3.1 What NDT Can and Cannot Detect 3.2 Surface vs Subsurface and Method Selection Logic 3.3 Product Forms: Welds, Castings, Forgings, Wrought, In-Service Damage

4 MT Principles & Flux Fields

4.1 Magnetism, Permeability, and Flux Leakage 4.2 Flux Fields: Circular vs Longitudinal 4.3 How Discontinuities Distort Magnetic Fields

5 MT Magnetization & Demagnetization

5.1 Magnetization by Electric Current: Contact, Prods, Central Conductor 5.2 Selecting the Proper Magnetization Method: Coils, Yokes, Current Type 5.3 Demagnetization Procedures and Residual Field Limits

6 MT Equipment, Evaluation & Process Control

6.1 MT Equipment, Media, and Lighting 6.2 Types of Discontinuities Detected by MT 6.3 MT Evaluation Techniques 6.4 Quality Control of MT Equipment and Processes

7 PT Principles & Materials

7.1 PT Principles: Capillarity, Wetting, and Process Physics 7.2 Penetrant Types, Methods, and Sensitivity Classes 7.3 Developers and Process Sequence Controls

8 PT Method Selection & Process Control

8.1 Selecting the Appropriate PT Method for the Job 8.2 Surface Preparation, Dwell, Removal, and Lighting 8.3 Station Equipment, Process Control, and Safety

9 PT Indications, Evaluation & Standards

9.1 Relevant, Nonrelevant, and False Indications 9.2 Evaluating Indication Size, Shape, and Persistence 9.3 PT Procedures, ASTM/ASME Standards, and Acceptance

10 RT Principles & Exposure Technique

10.1 Radiation Physics: X-ray vs Gamma, Energy, and Attenuation 10.2 Exposure Geometry, Inverse Square Law, and Geometric Unsharpness 10.3 Radiographic Technique: kV, mA-min, Screens, and Source Selection

11 RT Image Quality, Processing & Indications

11.1 Film, Digital Detectors, Density, and Image Quality Indicators 11.2 Darkroom Facilities, Processing, and Artifact Control 11.3 Radiographic Indications, Discontinuities, and Defects

12 RT Product Discontinuities & Radiation Safety

12.1 Manufacturing Processes and Associated Discontinuities 12.2 Radiological Safety: Time, Distance, Shielding, and Dose Limits 12.3 RT Procedures, Codes, and Viewing Practice

13 UT Principles & Techniques

13.1 Sound Propagation, Modes, Velocity, and Wavelength 13.2 Transducers, Couplant, and Straight-Beam Techniques 13.3 Angle-Beam Techniques, Snell's Law, and Skip Distance

14 UT Calibration & Base Material

14.1 Calibration Blocks, DAC, TCG, and Sensitivity Setting 14.2 Evaluating Base-Material Product Forms 14.3 Evaluating Weldments

15 UT Bonds, Detection & Evaluation

15.1 Evaluating Bonded Structures 15.2 Discontinuity Detection and Characterization 15.3 General Evaluation, Sizing, and Acceptance Logic

16 VT Scope, Vision & Lighting

16.1 Purpose and Scope of VT 16.2 Elements of Vision 16.3 Elements of Lighting 16.4 Contrast and Resolution

17 VT Optics, Equipment & Discontinuities

17.1 Optics and Magnification 17.2 VT Equipment: Direct, Remote, and Measuring Tools 17.3 Visual Appearance of Discontinuities

18 VT Evaluation, Codes & Employer Topics

18.1 Evaluation and Reporting 18.2 Codes, Standards, and Specifications 18.3 Employer-Specific Topics and Written-Practice Controls

19 Specific Exam: Codes & Sectors

19.1 How the Specific Exam Differs from the General Exam 19.2 General Industry Codes and Procedure Use 19.3 Pressure Equipment Sector Codes (ASME, NBIC, API context)

20 Specific Exam: Applications & Techniques

20.1 Applications: Matching Method to Product Form and Access 20.2 Technique Selection and Essential Variables 20.3 Procedure Compliance, Reporting, and Acceptance/Rejection

21 Exam Strategy & Maintenance

21.1 Timed 50+40 Strategy and CBT Rules 21.2 Common Traps by Method 21.3 Weak-Area Review and Recertification Planning

5.3 Demagnetization Procedures and Residual Field Limits

Key Takeaways Explain This Topic AI

Demagnetize when residual field would hold chips, disturb instruments, spoil welding or coating, or fight a later magnetic particle shot.

Decaying alternating current is the usual shop method; reversing direct-current step-down is for thick or deeply magnetized parts; alternating-current yoke withdraw is the local field method.

Verify residual field with a field indicator or Hall-effect/gauss meter at the locations the procedure names; a part can be clean in the middle and still a magnet at a pole.

A commonly cited shop limit is about ≤3 gauss (0.3 mT); that is a typical procedure figure, not an ASNT-published universal number, and aerospace, weld-prep, and compass-adjacent parts may be much tighter.

Last updated: August 2026

Official MT general topic 6 on the outline administered prior to 15 December 2026 is Demagnetization Procedures . Passing the written exam means you know why a residual field is a problem, how shops take it out, how they prove it is gone, and that the numeric limit lives in the procedure , not in a single ASNT constant.

Why demagnetize

A ferromagnetic part that leaves the magnetic particle booth still magnetized can:

Hold chips and swarf on subsequent machining, grinding, honing, or assembly

Disturb instruments — magnetic compasses, some avionics sensors, nearby meters, and some electron-beam or welding equipment

Interfere with later processing — welding arc blow , uneven coating or plating, chips trapped under paint

Mask or distort a later MT exam if a leftover field from the first shot fights the next field or makes a residual-method shot meaningless

Attract debris in service on bearings, hydraulic components, and aerospace mechanisms

Not every part must be demagnetized. Soft, low-retentivity parts that were magnetized only with alternating current may already sit near zero because AC is self-demagnetizing . Many written practices require demagnetization only when residual field would affect the next operation or the customer specification. Hard steels after a heavy direct-current or full-wave shot almost always need a planned demagnetization step.

Do not demagnetize before a residual-method particle application. Residual inspection uses the retained field on purpose. Demagnetize after evaluation (or before a conflicting later shot) when the procedure requires a known low residual.

How residual field is removed

Demagnetization works by cycling the material around a shrinking hysteresis loop until the domains are left disordered. Each reversal is a little weaker than the last. A single opposite pulse that is too strong simply remagnetizes the part the other way.

Method How it is done Typical use

Decaying alternating current The part passes through an AC coil, or AC amplitude is reduced to zero while the part is in the coil Most production shops; also the reason AC magnetization tends to leave little residual

Reversing DC step-down Direct-current polarity reverses while current is reduced in programmed or manual steps Large or thick parts that AC skin effect will not fully penetrate

Yoke withdraw An energized alternating-current yoke is pulled off the part along its length, or the part is withdrawn from the yoke field Field welds and local spots after yoke magnetic particle testing

Decaying AC is the workhorse. The part is drawn slowly through a 50/60 Hz coil, or the coil current is ramped down, so each half-cycle reverses the field at a slightly lower amplitude. Pulling too fast leaves residual. Leaving the part at the coil mouth in a strong AC field and yanking it sideways can remagnetize a local zone. Long bars may need more than one pass, reversing the direction of travel, so both ends see a decaying field.

Reversing DC is for parts alternating current cannot finish: heavy sections, deep residual from a full-wave or DC shot, or materials where the AC skin effect leaves the core magnetized after the surface looks clean. The operator or the bench program reverses polarity and steps the current down to a low value. Skipping steps, or ending on a large pulse, leaves a leftover pole.

Yoke withdraw is the portable version of decaying AC: keep the AC yoke energized and slide it away so the part sees a reversing, diminishing field. A DC yoke pulled off the part can leave residual field. Do not treat DC yoke removal as demagnetization unless the written practice says that specific motion is the qualified method.

Verify with a field indicator or gauss meter

"It looks demagnetized" is not a measurement. Particles falling off the part only tell you the field is no longer holding that powder. They do not give a residual-field number.

A field indicator (pocket compass-type or a dedicated residual indicator) shows whether a residual field is still steering the needle.

A Hall-effect probe / gauss meter gives a number, usually in gauss or millitesla . Conversion you should know: 1 mT = 10 gauss , so 0.3 mT = 3 gauss .

Measure at the locations the procedure names — often ends, last contact points, coil-mouth positions, gear teeth, and other geometric poles. A part can be quiet in the middle and still a magnet at a sharp end or a thread. If the next process is machining, measure after the part is out of the bench's stray field , not while it is sitting against a steel table that is itself magnetized.

Probe orientation matters. Follow the meter and procedure: residual checks are often taken with the probe in a stated orientation relative to the surface. A single lucky low reading on the mid-span OD does not clear a shaft that still grabs chips at the headstock end.

Residual limits are procedure-specific

ASNT does not publish one universal residual-field number as the Level II pass/fail criterion. Many shop practices and customer specifications use a typical limit of about 3 gauss (0.3 mT) or less at the surface. Some commodity work allows more. Aerospace, landing-gear, engine, and instrument-near parts are often much tighter and may require a documented survey at named locations.

Teach it this way on the exam:

If the stem gives a limit, use that limit

If the stem asks for a commonly cited shop number, ≤3 gauss / 0.3 mT is the usual textbook figure — and you must label it as a typical procedure limit , not an ASNT-published constant

Tighter than 3 gauss is common when the part will fly, go near a compass, enter a precision coating line, or be welded next

A residual reading is not an amperage setting. Three gauss is not "set the head shot to 3." It is a leftover field after demagnetization, measured with a field indicator or gauss meter.

Special cases the exam likes

Parts that will be welded. Residual field causes arc blow : the arc wanders, undercut appears, and fusion can suffer. Demagnetize weldments, adjoining fittings, and sometimes the fixture before a critical weld, even if the leftover field would have been acceptable for chip control alone. A "3 gauss is always fine" answer is wrong when the next operation is a qualified weld.

Aerospace residual limits. Engine rotating parts, landing gear, actuators, and flight-control hardware often carry customer or prime-contractor residual limits well below the generic 3-gauss shop card. Some travelers require a gauss-meter survey at named stations and a recorded value. Follow the traveler. Do not "shop-limit" an aerospace part because that is what the structural shop uses on plate.

Shipping near compasses and avionics. Large magnetized structures — pipe, plates, assembled gearboxes, spare rotors — can deflect a magnetic compass or upset nearby sensors. Export, aircraft, and some marine rules care about this. Demagnetize and verify before the part is crated next to instruments, loaded near a compass, or installed in an assembly that will be compass-swung.

Subsequent magnetic particle testing. If a residual circular field remains, a later longitudinal shot can produce confusing particle patterns (including magnetic writing). A residual-method exam on the next shift is meaningless if yesterday's field is still in the part. Demagnetize between conflicting shots when the procedure requires a known starting state.

Mixed operations. A part that was prodded in the field, then sent to a wet bench, then finish-machined, may need demagnetization at more than one gate. Each gate uses that procedure's limit. The field exam's "good enough for the weld overlay" is not automatically good enough for the machine shop or the paint line.

Putting the sequence together

A complete Level II mental checklist after the last evaluation:

Does the written practice or customer specification require demagnetization for this part and the next operation?

Choose decaying AC if the section is within AC reach; choose reversing DC step-down if the residual is deep or the section is thick.

Use yoke withdraw only for local AC yoke work, and do not confuse it with pulling off a DC yoke.

Verify with a field indicator or gauss meter at the specified points, away from stray bench fields.

Compare the reading to this job's residual limit — commonly ≤3 gauss / 0.3 mT in general shop practice, tighter in aerospace, weld-prep, and instrument work.

Document as the procedure requires. A demagnetization that is not measured is not finished.

On the general exam, a stem that names chips on a lathe, arc blow on the next weld, a compass in the crate, or a later MT shot is asking why you demagnetize. A stem that names a thick full-wave-DC forging is asking reversing DC , not a single surface AC kiss. A stem that names 3 gauss is asking you to treat that figure as a procedure-typical limit , not as ASNT's one published number for every part.