Study guide
7.2 Wrought and Primary Forming Discontinuities
ASNT NDT Level III Magnetic Particle Testing MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Magnetization Principles and Physics
1.1 Magnetic Fields, Poles, and Domain Theory 1.2 The Hysteresis Loop and B-H Curve 1.3 Longitudinal vs. Circular Magnetization Fields 1.4 Magnetic Flux Leakage Theory and Defect Detectability 1.5 Probability of Detection, Reliability, and Technique Validation
2 Chapter 2: Direct Contact and Longitudinal Magnetization Techniques
2.1 Head Shots and Direct Contact Techniques 2.2 Prod Techniques and Localized Circular Magnetization 2.3 Longitudinal Coil Magnetization and Calculations
3 Chapter 3: Central Conductor, Yoke, and Vector Magnetization
3.1 Central Conductor (Induced Current) Techniques 3.2 Electromagnetic Yokes and Portable Field Techniques 3.3 Multidirectional and Vector Magnetization
4 Chapter 4: Magnetic Particles and Carrier Vehicles
4.1 Particle Characteristics: Physical, Magnetic, and Optical Properties 4.2 Dry Powder Systems and Application Techniques 4.3 Wet Particle Systems: Water vs. Petroleum Distillate Vehicles 4.4 Bath Concentration, Centrifuge Settling, and Maintenance
5 Chapter 5: Electrical Waveforms, Equipment, and Demagnetization
5.1 Current Waveforms and Penetration: AC, HWDC, FWDC, and 3-Phase FWDC 5.2 Stationary Wet Horizontal Benches and Portable Units 5.3 Demagnetization Principles, Methods, and Residual Field Limits
6 Chapter 6: Quality Control, Calibration, and System Performance
6.1 Lighting and Viewing Environment Requirements 6.2 Field Indicators and System Performance Check Devices 6.3 Equipment Calibration and Periodic Verifications 6.4 Bath Contamination, Water Break, and Cleanliness Tests
7 Chapter 7: Inherent and Primary Processing Discontinuities
7.1 Ingot and Casting Discontinuities 7.2 Wrought and Primary Forming Discontinuities 7.3 Secondary Processing Discontinuities: Machining and Heat Treating
8 Chapter 8: Service Discontinuities and Indication Evaluation
8.1 Service Discontinuities: Fatigue, Stress Corrosion, and Creep 8.2 Welding Discontinuities and Weldment Examination 8.3 Indication Classification: Relevant, Non-Relevant, and False 8.4 MT Reports, Records, and Documentation Review
9 Chapter 9: Industry Codes, Standards, and Acceptance Criteria
9.1 ASME Section V, Article 7 (Mandatory MT Requirements) 9.2 ASTM E1444 vs. ASTM E709 vs. ISO 9934 9.3 Acceptance Criteria in Fabrication Codes: ASME VIII, AWS D1.1, and API 1104 9.4 Reviewing Client Requirements and Product-Form MT Specifications
10 Chapter 10: Level III Responsibilities, Procedures, Training, and Program Oversight
10.1 Level III Duties, SNT-TC-1A, and ANSI/ASNT CP-189 10.2 Preparation and Qualification of MT Written Procedures 10.3 Safety, Environmental, and Health Considerations in MT 10.4 Developing and Delivering MT Training Programs 10.5 Developing and Administering MT Qualification Examinations 10.6 MT Program Audits, Supplier Oversight, and Personnel Performance
7.2 Wrought and Primary Forming Discontinuities
Key Takeaways Explain This Topic AI
Primary mechanical working operations (rolling, forging, extrusion, drawing) elongate cast dendritic grains and inherent flaws into directional fibrous grain flow oriented parallel to the principal axis of working.
Seams are straight, tight longitudinal fissures running strictly parallel to the working axis, originating from oxidized ingot cracks, opened near-surface blowholes, or improper roll passes, requiring circular magnetization for detection.
Forging and rolling laps are mechanical folds created when excess metal (fins or overfill) is pressed flat into the workpiece without welding, producing curvilinear or oblique indications that enter the surface at an angle.
Hydrogen flakes (shatter cracks) are internal micro-fissures in heavy alloy forgings caused by the precipitation of entrapped atomic hydrogen into molecular gas voids, developing massive localized hydrostatic pressures during cooling.
Internal plate laminations lie in the mid-thickness plane parallel to the rolled plate surfaces; because surface magnetic fields travel parallel to the planar separation, MT cannot detect laminations on plate faces unless they break out at cut edges.
Last updated: September 2026
- 7.2 Wrought and Primary Forming Discontinuities
- Primary Mechanical Working and Grain Flow Dynamics
Wrought manufacturing processes convert cast ingots or continuously cast blooms and billets into structural shapes, bars, plates, forgings, and seamless tubing through severe plastic deformation. Primary working operations include hot rolling , open-die forging , closed-die forging , extrusion , and cold drawing .
The Formation of Fiber Texture and Grain Flow
During plastic deformation above the recrystallization temperature, the coarse, randomly oriented equiaxed and columnar cast dendrites are broken down, refined, and elongated. Non-metallic inclusions (such as ductile manganese sulfides), segregation bands, and remaining micro-voids are stretched in the direction of plastic extension. This microstructural re-orientation establishes a directional fibrous pattern known as grain flow (or fiber texture).
Transformation of Inherent Flaws: Mechanical working fundamentally alters the physical geometry of ingot discontinuities:
Three-dimensional globular voids or inclusions are squeezed and elongated into two-dimensional planar or one-dimensional linear discontinuities.
Discontinuities become oriented parallel to the direction of principal metal flow.
Unoxidized internal gas blowholes and microshrinkage voids can forge-weld shut under hot compressive hydrostatic pressure. Conversely, oxidized voids, non-metallic inclusions, and surface-connected cracks cannot weld and instead lengthen into severe primary forming discontinuities.
- Primary Forming Discontinuity Types and Formation Mechanisms
- Seams (Rolling, Forging, and Drawing Seams)
Seams are among the most common and structurally dangerous discontinuities found in rolled bar stock, drawn wire, and finished shafts.
Origin Mechanisms:
Opened Subsurface Blowholes: Near-surface gas blowholes in the ingot that oxidize when heated in the soaking pit break open during the initial rolling passes, elongating into continuous longitudinal surface fissures.
Ingot Surface Tears: Thermal stress cracks or mold scabs on the ingot surface that oxidize and are rolled out into long, tight crevices.
Roll Pass Underfill and Mechanical Grooving: Defective rolls, improper roll pass drafting, or mechanical guide scratching that tears the bar surface during processing.
Morphology: Seams are straight, tight, linear cracks running strictly parallel to the longitudinal axis of the wrought product. They are typically perpendicular to the outer surface in depth and can extend intermittently or continuously for lengths ranging from several millimeters to tens of meters.
Detection Physics: Because seams run parallel to the length of a bar or cylinder, circular magnetization (direct current passed through the part via headstocks, or through a central conductor) is mandatory. Circular magnetization establishes magnetic flux lines traveling circumferentially ( 360 ∘ 360^\circ 36 0 ∘ around the bar), cutting across the longitudinal seam at an optimal 90 ∘ 90^\circ 9 0 ∘ angle to create maximum flux leakage. Longitudinal magnetization (encircling coil) directs flux parallel to the seam, generating zero leakage and causing complete inspection failure. Longitudinal Seam in Rolled Bar Stock
- Circular Flux (Headstock Shot) Longitudinal Flux (Encircling Coil Shot)
- [Optimal: 90° Cut] [Ineffective: Parallel to Flaw]
- +-----------------+ +-----------------+
- | ============ | Seam | ============ | Seam
- | ============ | | ============ |
- +-----------------+ +-----------------+
- | ^ -----> ----->
- v | Flux Lines (Parallel)
- Circular Flux NO FLUX LEAKAGE
- SHARP MT INDICATION FLAW CANNOT BE DETECTED
- Laps (Forging and Rolling Laps)
Laps are mechanical folding defects that occur during hot working operations.
Formation Mechanism: During rolling or closed-die forging, an overfill occurs when excessive metal enters a roll pass or die cavity, squeezing out between the dies as a protruding ridge, fin, or flash. In the subsequent pass or forging blow, this protruding fin is bent over and flattened into the surface of the workpiece. Because the surface of the fin is coated with iron oxide mill scale, the folded metal cannot forge-weld to the base material.
Morphology: Unlike seams, laps enter the metallic surface at an oblique or acute angle (often 10 ∘ 10^\circ 1 0 ∘ to 45 ∘ 45^\circ 4 5 ∘ relative to the surface plane). On forgings, laps often follow the contour of the parting line, die fillets, or web-to-flange transitions, presenting a curvilinear, crescent-shaped, or wavy visual appearance.
Magnetic Particle Response: Because laps penetrate at an angle, the magnetic flux leakage field is slightly broader than that of a vertical crack or seam. However, because the lap boundary reaches the surface, high-sensitivity fluorescent wet suspensions reveal distinct, sharp, continuous linear indications following the fold trace.
Non-Metallic Stringers
During ingot rolling, ductile non-metallic inclusions—principally manganese sulfides ( MnS \text{MnS} MnS ) and certain plastic silicate glasses—deform plastically alongside the steel matrix.
Morphology: These inclusions are flattened and elongated into thin, microscopic ribbons or discontinuous parallel chains of non-metallic particles running parallel to the direction of rolling. Under magnification, stringers resemble broken pencil lines running through the microstructure.
Magnetic Indication Characteristics:
Inclusions have low magnetic permeability ( μ r ≈ 1 \mu_r \approx 1 μ r ≈ 1 ), creating small localized leakage fields when cutting perpendicular flux lines.
Magnetic particle indications appear as fine, faint, intermittent, broken linear chains parallel to the grain flow.
Level III Engineering Distinction: Non-metallic stringers are inherent microstructural features present to some degree in all commercial steels (especially resulfurized free-machining grades like AISI 1117 or 1215). The Level III must establish rigorous acceptance criteria: isolated, short stringers are generally harmless in low-stress regions, whereas dense clusters of stringers in high-strength aerospace components or critical rotating journals act as fatigue crack initiation sites and must be rejected.
Forging Bursts (Centerline Bursts and Chevron Cracking)
Forging bursts are internal mechanical ruptures formed during forging, upsetting, or extrusion.
Root Metallurgical Causes:
Improper Forging Temperature: Forging metal when it is too hot (within the "hot-short" temperature range where grain boundary liquid films form) causes intergranular tearing. Forging metal when it is too cold (below recrystallization temperatures) lowers ductility, causing brittle cleavage ruptures under heavy reduction.
Excessive Tensile Stresses: In open-die forging or extrusion, improper die angles, excessive draft, or poor feed-to-height ratios ( h / d h/d h / d ) generate severe secondary tensile triaxial stresses along the central neutral axis of the billet. When these internal tensile stresses exceed the ultimate tensile strength of the hot core, the core tears apart internally.
Morphology: Bursts are internal, jagged, star-shaped, or chevron-patterned cavities centered along the longitudinal centerline of the forging.
MT Detectability: Bursts are entirely internal during primary forging. Standard surface MT cannot detect forging bursts in as-forged billets because the solid metal outer shell prevents magnetic flux leakage from reaching the exterior. Bursts are only detectable by magnetic particle testing when subsequent machining, drilling, or boring operations cut through the core, exposing the burst cavity to the surface. Prior to machining, ultrasonic testing (UT straight beam) is the primary method required for burst detection.
Hydrogen Flakes (Shatter Cracks / Fish Eyes)
Hydrogen flakes represent one of the most catastrophic internal defects encountered in heavy alloy steel forgings, thick blooms, and railroad rails.
Physical Formation Mechanism:
Dissolution in Molten Steel: Molten steel dissolves atomic hydrogen ( H H H ) from atmospheric humidity, damp raw materials, or furnace refractories.
Solubility Drop on Cooling: Hydrogen solubility is high in molten steel and liquid austenite, but drops drastically as the steel cools and transforms to body-centered cubic (BCC) ferrite or martensite. In heavy cross-sections, rapid surface cooling traps atomic hydrogen in the interior, preventing outward diffusion.
Recombination and Hydrostatic Pressure: Trapped atomic hydrogen diffuses to internal micro-voids, inter-dendritic boundaries, and inclusion interfaces, where it combines into molecular hydrogen gas ( 2 H → H 2 ↑ 2H \rightarrow H_2\uparrow 2 H → H 2 ↑ ). Because molecular hydrogen cannot diffuse through the metal lattice, gas molecules accumulate in micro-cavities, developing immense localized hydrostatic internal pressures exceeding thousands of megapascals ( > 1000 MPa >1000\text{ MPa} > 1000 MPa ).
Rupture Under Transformation Stresses: When this internal gas pressure combines with high cooling stresses and transformation stresses (austenite to martensite/bainite volume expansion), the internal metal matrix ruptures along grain boundaries, forming micro-fissures.
Morphology: Hydrogen flakes are internal, disc-shaped, circular cleavage cracks. In fractured test specimens, they appear as bright, silvery, oval patches termed "fish eyes." In cross-sections, they appear as fine, hairline cracks randomly oriented in the central and mid-radius zones of heavy forgings, rarely extending into the outer rim.
MT Detection: Like bursts, flakes are volumetric internal defects undetectable by surface MT until the forging is sectioned or bored. When deep hole boring or rough machining exposes flakes to the inner or outer bore surface, high-sensitivity fluorescent wet continuous MT reveals clusters of sharp, hairline, multi-directional cracks.
Laminations in Rolled Plate
Laminations are extensive, flat, two-dimensional internal separations found in rolled plate, strip, and sheet.
Origin: Laminations originate from uncropped primary or secondary pipe cavities, large oxidized blowholes, or dense planar clusters of non-metallic inclusions in the original ingot. When the ingot or slab is hot-rolled into flat plate, the internal cavity is flattened and spread out laterally, producing a wide planar separation located in the mid-thickness plane parallel to the plate surfaces.
The Plane of MT Inspection Trap:
Laminations lie flat, parallel to the top and bottom rolled faces of the plate.
When magnetic fields are introduced into the plate (via electromagnetic yokes or prods), the magnetic flux lines travel through the plate thickness along planes parallel to the lamination.
Because the flux runs parallel to the planar separation, no magnetic flux leakage is forced outward through the top or bottom surface. Surface magnetic particle examination of rolled plate faces is completely incapable of detecting internal laminations.
Laminations can only be detected with MT when they break out at cut plate edges , sheared ends, or beveled weld preparations. At a cut edge, an applied magnetic field traveling across the plate thickness cuts the lamination at 90 ∘ 90^\circ 9 0 ∘ , producing a distinct linear particle indication along the mid-thickness centerline. Volumetric lamination screening across the plate body must be performed using ultrasonic straight-beam testing per ASTM A435 or ASTM A578.
Summary Comparison Table: Wrought and Primary Forming Discontinuities
Discontinuity Type Primary Working Process Orientation Relative to Grain Flow Defect Morphology & Depth Primary Magnetization Technique Diagnostic Distinguishing Features
Seam Hot Rolling, Cold Drawing Strictly parallel to longitudinal grain flow Straight, tight, continuous or intermittent; perpendicular in depth Circular Magnetization (Headstocks or Central Conductor) Linear, razor-straight indication; invisible under longitudinal coil field
Lap Forging, Hot Rolling Parallel to grain flow; follows die parting / fillets Wavy, curvilinear, crescent-shaped; enters surface at oblique angle ( 10 ∘ – 45 ∘ 10^\circ\text{--}45^\circ 1 0 ∘ – 4 5 ∘ ) Circular / Multi-directional with Wet Fluorescent continuous Follows flow lines; slightly broader powder ridge than straight seams
Stringer Hot Rolling of Alloy Steels Parallel to major axis of elongation Extremely fine, broken, parallel chains ("pencil lead" appearance) Circular Magnetization ; High-sensitivity wet fluorescent Discontinuous fine lines; caused by elongated MnS \text{MnS} MnS /silicate inclusions
Forging Burst Open-Die & Closed-Die Forging, Extrusion Along longitudinal centerline / core Internal, jagged, star-shaped or chevron-patterned cavity Internal defect; Surface MT invalid until exposed by machining Detectable by MT only after boring or sectioning; primary NDT is UT
Hydrogen Flake Heavy Alloy Forgings, Blooms Random or radial within core and mid-radius Internal, disc-shaped, circular micro-fissures ("fish eyes") Internal defect; Fluorescent wet MT after boring/machining Fine hairline radial cracks on bore ID; UT straight-beam before machining
Lamination Flat Plate & Strip Rolling Parallel to flat rolled plate surfaces Planar mid-thickness separation; extensive area MT valid ONLY at cut plate edges or weld prep bevels Top/bottom plate surface MT fails; must use UT straight-beam for body
- Practical Level III Engineering Scenarios and Exam Traps
- Scenario 1: The Encircling Coil Seam Inspection Error
A fabrication shop receives a shipment of 3-inch (76 mm) diameter AISI 4140 hot-rolled bars. The customer specification requires 100% magnetic particle testing for longitudinal seams. The Level II technician places each bar horizontally inside a 5-turn encircling coil, energizes the coil with 2500 Amperes AC, sprays wet fluorescent bath, and reports zero indications across 50 consecutive bars. During subsequent CNC turning, longitudinal seams up to 0.040 inch (1.0 mm) deep open up on nearly 30% of the shafts.
Level III Technical Root-Cause Analysis:
Magnetic Physics Failure: An encircling coil generates a longitudinal magnetic field parallel to the cylindrical axis of the bar. Because the seams run longitudinally along the bar, the magnetic flux lines travel completely parallel to the seam crevices. Zero flux leakage is created, rendering even deep seams completely invisible.
Mandatory Technique Modification: The inspection must be redesigned to utilize circular magnetization . The bar must be clamped between copper headstocks, and an electrical current passed directly through the bar ( I = 20 to 30 A/mm I = 20\text{ to }30\text{ A/mm} I = 20 to 30 A/mm of diameter, or ≈ 1500 to 2200 A \approx 1500\text{ to }2200\text{ A} ≈ 1500 to 2200 A per ASTM E1444), establishing circumferential flux that intersects the longitudinal seams at 90 ∘ 90^\circ 9 0 ∘ . Re-inspection of the quarantined lot using headstock contact reveals distinct, brilliant fluorescent linear indications across all defective bars.
Scenario 2: Plate Lamination at Weld Bevel Preparation
During the fit-up of a 2-inch (50 mm) thick pressure vessel shell plate conforming to ASME SA-516 Grade 70, the welding inspector tests the double-V weld prep bevel using an AC yoke and dry red powder. A sharp linear indication appears along the exact mid-thickness centerline of the bevel, extending continuously for 18 inches (450 mm). The shop foreman claims the indication is merely a non-relevant "machining mark from the bevel planer."
Level III Disposition Protocol:
Verification: The Level III lightly dresses the bevel surface with fine emery paper (600 grit) to eliminate tool chatter marks and re-tests using an AC yoke with the poles straddling the bevel edge ( 90 ∘ 90^\circ 9 0 ∘ to the edge). The indication reappears with identical intensity.
Flaw Classification: The indication is confirmed as an edge-breakout lamination originating from an uncropped ingot pipe cavity flattened during plate rolling.
Remediation: Because the lamination provides a direct leak path and risk of lamellar tearing under weld contraction stresses, the Level III performs straight-beam ultrasonic testing (UT per ASTM A578) to map the lamination's depth into the plate body. The UT survey reveals the lamination extends 4 inches (100 mm) back from the weld bevel, exceeding ASME Section VIII acceptance thresholds and requiring gouging and weld repair or plate section replacement.