Study guide

Check Standards and Statistical Process Control

ASQ Certified Calibration Technician CCT

Track your progress as you read

Finished sections get a check mark.

1 SI Definitions and Realizations

The Seven SI Base Units and the 2019 Revision Realizing SI Units in the Laboratory

2 Derived Units, Prefixes, and Constants

Derived Units and Physical Calculations SI Prefixes and Compound-Unit Conversions Physical Constants and Their Applications

3 Measurement Standards and Selection

Types and Roles of Measurement Standards Selecting Standards for an Operational Hierarchy

4 Traceability and Standard Substitution

Traceability Evidence and Impact Review Evaluating and Authorizing Standard Substitution

5 Dimensional and Mechanical Metrology

Linear Displacement and Dimensional Instruments Geometry, Thermal Expansion, and Mass Force, Torque, Pressure, Density, and Viscosity

6 Temperature, Humidity, Volume, and Flow

Temperature Sensors and Thermometer Corrections Humidity, Volume, and Flow

7 Electrical, Optical, and Time Measurements

Voltage, Current, Resistance, and AC Measurement Time, Frequency, Light, Power, and Energy

8 Measurement Methods

Direct, Indirect, and Ratio Methods Transfer, Differential, and UUT Substitution Methods

9 Instrument Characteristics and Measurement Data

Sensitivity, Variability, and Precision Bias, Linearity, Stability, and Hysteresis Data Formats, Readability, and Suitability Resolution, Confidentiality, and Data Integrity

10 Specifications and Error Sources

Interpreting IM&TE Specification Terms Specification Calculations and Operating Qualifiers Instrument, Operator, and Circuit Errors Environmental, Geometric, and Interference Errors

11 Measurement Assurance

Check Standards and Statistical Process Control Proficiency Comparisons and Gage R&R

12 Procedures and Governing Requirements

Procedure Structure and Published Practice Sources Method Development, Deviations, and Handling Regulations, Contracts, and Requirement Precedence

13 Instrument Adjustment and Standardization

Calibration, Zero, and Span Adjustment Linearization, Nulling, and Digital Adjustment

14 Calibration Environment

Temperature and Humidity Control ESD, Dust, Vibration, and Pressure

15 Operations, Roles, and Scheduling

Receiving, As-Found Testing, and Calibration Flow Asset Identification, Tracking, and Release Laboratory Roles and Initial Scheduling Interval Review, Overdue Control, and Workloads

16 Method and Software Validation

Method Verification and Validation Studies Software, Firmware, and Spreadsheet Validation

17 Records and Formal Reporting

Controlled Records and Calibration Certificates Status Labels and Out-of-Tolerance Reporting

18 Uncertainty Concepts and Decision Risk

Error, Uncertainty, and Measurand Definition TAR, TUR, Tolerance Consumption, and Capability Conformity Decisions and False-Accept Risk Guard Bands and Conformity Reporting

19 Uncertainty Models and Budgets

Measurement Models and Uncertainty Contributions Distribution Selection and Budget Assembly

20 Type A and Type B Evaluation

Type A Statistics and Repeatability Outlier Review and Worked Type A Analysis Type B Distribution Models

21 Uncertainty Reporting and Applied Mathematics

Propagation, Covariance, and Effective Degrees of Freedom Coverage Factors and Expanded-Uncertainty Reporting Notation, Unit Conversions, Ratios, and Decibels Rounding, Algebra, Graphs, and Angular Conversions

22 Quality Systems and Tools

Quality-System Components, Planning, and Improvement The Seven Basic Quality Tools

23 Audits and Corrective Action

Audit Types, Planning, and Nonconformance Control Impact Assessment, Root Cause, and Effectiveness

24 Safety, Standards, and Professional Conduct

Electrical, Pressure, Chemical, and Laboratory Hazards PPE, Safety Data Sheets, 6S, and Safe Restoration Quality Standards, GUM, and VIM Accreditation Scope and Professional Ethics

Check Standards and Statistical Process Control

Key Takeaways Explain This Topic AI

A check standard provides evidence of process behavior between periodic calibrations.

Control limits estimate process variation and must be distinguished from specification limits.

An I-MR chart can estimate individual-reading spread from the average moving range using the appropriate factor.

Last updated: October 2026

Metrology Subject Focus: Calibration laboratories must maintain ongoing statistical control of their measurement processes through Measurement Assurance Programs (MAP), check standards, interlaboratory proficiency testing, and Gage R&R capability studies.

In high-reliability calibration and manufacturing environments, periodic artifact calibration alone cannot guarantee measurement integrity. An instrument calibrated in January may suffer an undetected component failure, physical shock, or excessive drift in February, remaining in service and producing defective calibrations until its next scheduled verification twelve months later.

A Measurement Assurance Program (MAP) monitors the measurement process through suitable check standards, observations, and statistical controls. It can reveal changes between periodic calibrations and support uncertainty evaluation. It cannot detect every failure instantly; sampling frequency, shared influences, and check-standard stability matter.

The Metrological Check Standard

The central pillar of any MAP is the check standard (sometimes termed a surveillance standard or control artifact).

Check Standard Criteria and Operational Rules

Functional Independence: Choose a check that can detect the effects of concern. Evaluate shared influences and the check standard’s own drift. Measure it as an unknown using representative procedures, fixtures, and personnel; physical separation alone does not establish independent evidence.

Long-Term Stability: The check standard artifact must possess proven physical and temporal stability. Typical check standards include precision Zener voltage references, standard resistors in temperature-stabilized baths, Class 1 stainless steel mass standards, Grade 0 ceramic gauge blocks, and resonant quartz pressure transducers.

Frequent Surveillance Cycles: The check standard is calibrated at regular, predefined operational intervals (e.g., daily, at the start of each shift, or immediately before and after calibrating high-value customer standards). Each measurement result is logged in real time.

Process indicator: A check standard samples the effects represented by its quantity, range, method, and observation schedule. Its results can reveal environmental, operator, comparator, or reference changes, but cannot prove stability of every range or detect every intermittent failure.

Statistical Process Control (SPC) in the Calibration Laboratory

Data collected from check standard measurements are plotted on Shewhart control charts to evaluate whether the measurement system is in a state of statistical control .

X ˉ \bar{X} X ˉ and R R R Control Charts (Subgrouped Data)

When several replicate measurements of the check standard ( n = 3 to 5 n = 3\text{ to }5 n = 3 to 5 ) are taken during each surveillance interval, an X ˉ \bar{X} X ˉ and R R R chart is employed:

X ˉ \bar{X} X ˉ Chart (Mean): Tracks the average value across subgroups. Monitors process central tendency, detecting systematic calibration offsets, reference standard drift, and ambient temperature shifts.

R R R Chart (Range): Tracks the dispersion within subgroups ( R = X max − X min R = X_{\text{max}} - X_{\text{min}} R = X max ​ − X min ​ ). Monitors process repeatability, detecting electrical noise, thermal turbulence, comparator looseness, or operator variability.

Individuals and Moving Range ( I - M R I\text{-}MR I - MR ) Charts

In high-echelon calibration laboratories, performing multiple replicate measurements on a check standard every day is often economically or technically impractical ( n = 1 n = 1 n = 1 ). Under these conditions, the Individuals ( I I I ) and Moving Range ( M R MR MR ) chart is standard:

Individual Measurement ( X i X_i X i ​ ): The raw reading of the check standard recorded on day i i i .

Moving Range ( M R i MR_i M R i ​ ): The absolute difference between successive individual readings: M R i = ∣ X i − X i − 1 ∣ MR_i = |X_i - X_{i-1}| M R i ​ = ∣ X i ​ − X i − 1 ​ ∣

Calculating I - M R I\text{-}MR I - MR Control Limits

Given k k k individual observations:

Calculate the Process Centerline (Grand Mean): X ˉ = 1 k ∑ i = 1 k X i \bar{X} = \frac{1}{k}\sum_{i=1}^k X_i X ˉ = k 1 ​ i = 1 ∑ k ​ X i ​

Calculate the Average Moving Range: M R ‾ = 1 k − 1 ∑ i = 2 k M R i \overline{MR} = \frac{1}{k-1}\sum_{i=2}^k MR_i MR = k − 1 1 ​ i = 2 ∑ k ​ M R i ​

Estimate the Process Standard Deviation ( σ ^ \hat{\sigma} σ ^ ) using the unbiasing constant d 2 = 1.128 d_2 = 1.128 d 2 ​ = 1.128 (for sample size n = 2 n=2 n = 2 ): σ ^ = M R ‾ d 2 = M R ‾ 1.128 \hat{\sigma} = \frac{\overline{MR}}{d_2} = \frac{\overline{MR}}{1.128} σ ^ = d 2 ​ MR ​ = 1.128 MR ​

Establish Individuals ( I I I ) Control Limits: Upper Control Limit (UCL) I = X ˉ + 3 σ ^ = X ˉ + 3 ( M R ‾ 1.128 ) = X ˉ + 2.66 M R ‾ \text{Upper Control Limit (UCL)}_I = \bar{X} + 3\hat{\sigma} = \bar{X} + 3\left(\frac{\overline{MR}}{1.128}\right) = \bar{X} + 2.66\,\overline{MR} Upper Control Limit (UCL) I ​ = X ˉ + 3 σ ^ = X ˉ + 3 ( 1.128 MR ​ ) = X ˉ + 2.66 MR Lower Control Limit (LCL) I = X ˉ − 3 σ ^ = X ˉ − 3 ( M R ‾ 1.128 ) = X ˉ − 2.66 M R ‾ \text{Lower Control Limit (LCL)}_I = \bar{X} - 3\hat{\sigma} = \bar{X} - 3\left(\frac{\overline{MR}}{1.128}\right) = \bar{X} - 2.66\,\overline{MR} Lower Control Limit (LCL) I ​ = X ˉ − 3 σ ^ = X ˉ − 3 ( 1.128 MR ​ ) = X ˉ − 2.66 MR

Establish Moving Range ( M R MR MR ) Control Limits (where D 4 = 3.267 D_4 = 3.267 D 4 ​ = 3.267 and D 3 = 0 D_3 = 0 D 3 ​ = 0 for n = 2 n=2 n = 2 ): UCL M R = D 4 ⋅ M R ‾ = 3.267 M R ‾ \text{UCL}_{MR} = D_4 \cdot \overline{MR} = 3.267\,\overline{MR} UCL MR ​ = D 4 ​ ⋅ MR = 3.267 MR LCL M R = D 3 ⋅ M R ‾ = 0 \text{LCL}_{MR} = D_3 \cdot \overline{MR} = 0 LCL MR ​ = D 3 ​ ⋅ MR = 0

Control Limits vs. Specification Limits

Caution

Critical Metrological Distinction: Never plot manufacturer equipment specifications or process tolerance boundaries as control limits on an SPC chart.

Control Limits represent the natural statistical capability of the measurement system ( ± 3 σ ^ \pm 3\hat{\sigma} ± 3 σ ^ ). They are derived solely from internal process data.

Specification Limits represent external contractual or functional requirements (tolerances). Confusing the two masks out-of-control conditions and invalidates measurement assurance.

Control-chart signal rules for Out-of-Control Conditions

Control charts are divided into three statistical zones on each side of the centerline:

  • Zone C: Centerline to ± 1 σ \pm 1\sigma ± 1 σ ( 68.27 % 68.27\% 68.27% of normal distribution)
  • Zone B: ± 1 σ \pm 1\sigma ± 1 σ to ± 2 σ \pm 2\sigma ± 2 σ ( 95.45 % 95.45\% 95.45% cumulative)
  • Zone A: ± 2 σ \pm 2\sigma ± 2 σ to ± 3 σ \pm 3\sigma ± 3 σ ( 99.73 % 99.73\% 99.73% cumulative)

The four classic Western Electric rules below identify statistical signals for investigation under the laboratory’s monitoring plan. The trend and stratification rules are additional commonly used Nelson-style rules. Select rules and response criteria deliberately; applying more rules changes the false-alarm rate, and a signal is not proof of a particular physical cause.

Rule 1 (Action Limit): A single point falls beyond Zone A ( > 3 σ > 3\sigma > 3 σ from the centerline). The measurement process is immediately stopped.

Rule 2 (Warning Limit): Two out of three consecutive points fall in Zone A or beyond on the same side of the centerline.

Rule 3: Four out of five consecutive points fall in Zone B or beyond on the same side of the centerline.

Rule 4 (Run of Eight): Eight consecutive points fall on the same side of the centerline. Indicates a systematic shift or uncorrected bias in the reference standard or instrumentation.

Rule 5 (Trend): Six consecutive points continuously increase or continuously decrease. Indicates steady instrument drift, component aging, or thermal gradient change.

Rule 6 (Stratification): Fifteen consecutive points fall in Zone C (within ± 1 σ \pm 1\sigma ± 1 σ of the centerline). Indicates artificially suppressed variance, such as incorrect limit calculations or data manipulation.