Study guide
8.5 M&TE Identification, Control, and Customer-Supplied Equipment
ASQ Certified Quality Technician CQT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Quality Philosophies, Principles, and Management Systems
1.1 Quality Philosophies & Pioneers 1.2 Quality Management Systems, Standards & Documentation 1.3 Customer-Supplier Relationships & Quality Culture
2 Chapter 2: Cost of Quality, Teams, and Professional Ethics
2.1 Cost of Quality (COQ) & Economic Trade-Offs 2.2 Quality Improvement Teams & Meeting Management 2.3 Professional Conduct & ASQ Code of Ethics
3 Chapter 3: Basic Quality Tools & Continuous Improvement
3.1 Process Mapping, Flowcharts, and SIPOC 3.2 Cause-and-Effect Analysis & Check Sheets 3.3 Pareto Analysis & Prioritization 3.4 Histograms & Scatter Diagrams
4 Chapter 4: Descriptive Statistics and Probability Distributions
4.1 Data Types, Sampling Methods, and Populations 4.2 Measures of Central Tendency and Dispersion 4.3 Normal Distribution & Z-Score Calculations 4.4 Discrete Distributions: Binomial, Poisson, and Hypergeometric
5 Chapter 5: Statistical Process Control (SPC) Fundamentals & Variables Charts
5.1 SPC Fundamentals & Process Variation 5.2 Control Limits vs. Specification Limits 5.3 X-bar and R Charts 5.4 X-bar & s Charts and Individual-Moving Range (I-MR) Charts
6 Chapter 6: Attributes Control Charts and Out-of-Control Patterns
6.1 Control Charts for Nonconforming Units: p and np Charts 6.2 Control Charts for Nonconformities: c and u Charts 6.3 Out-of-Control Rules & Process Analysis
7 Chapter 7: Process Capability and Performance Analysis
7.1 Process Stability Prerequisite & Capability Basics 7.2 Potential Capability (Cp) and Actual Capability (Cpk) 7.3 Process Performance (Pp, Ppk) and Long-Term vs. Short-Term Variation 7.4 One-Sided Tolerances and PPM Defect Calculations
8 Chapter 8: Metrology Fundamentals, Standards, and Calibration
8.1 Metrology Foundations & Environmental Controls 8.2 Precision Gage Blocks & Standards Hierarchy 8.3 Calibration Systems & NIST Traceability 8.4 Out-of-Calibration Procedures & Reverse Traceability 8.5 M&TE Identification, Control, and Customer-Supplied Equipment
9 Chapter 9: Measurement Instruments and Measurement System Analysis (Gage R&R)
9.1 Common Dimensional Hand Measuring Instruments 9.2 Fixed Gages, Optical Comparators, and CMM Systems 9.3 Measurement System Analysis: Bias, Linearity, and Stability 9.4 Variable Gage R&R: Repeatability and Reproducibility 9.5 Electronic, Weighing, and Force Measurement Equipment
10 Chapter 10: Technical Drawings, Tolerancing, and GD&T (ASME Y14.5)
10.1 Engineering Drawing Basics & Projection Methods 10.2 Datums and the Datum Reference Frame 10.3 Form and Orientation Controls in GD&T 10.4 Location, Profile, and Runout Controls with Modifiers 10.5 Classification of Product Characteristics and Defects
11 Chapter 11: Inspection Planning, Sampling Plans, and Material Disposition
11.1 Inspection Planning & Inspection Points 11.2 Acceptance Sampling & ANSI/ASQ Z1.4 11.3 Switching Rules & Variables Sampling (Z1.9) 11.4 Nonconforming Material Control & MRB Dispositions 11.5 Types of Measurements, Unit Conversion, and Rounding Rules
12 Chapter 12: Quality Audits
12.1 Quality Auditing Principles & Types 12.2 The Audit Process: Planning, Performance, and Reporting 12.3 Audit Tools and Techniques
13 Chapter 13: Risk Management, Corrective and Preventive Action, and Safety
13.1 Risk Assessment Inputs, Monitoring, and Control Plans 13.2 FMEA, Action Priority, and Technician Workplace Safety 13.3 Root Cause Analysis & Problem-Solving 13.4 Corrective and Preventive Action (CAPA) & Verification 13.5 Preventive Action, Mistake-Proofing, and Read-Across
8.5 M&TE Identification, Control, and Customer-Supplied Equipment
Key Takeaways Explain This Topic AI
ISO 9001:2015 clause 7.1.5 requires monitoring and measuring resources to be identified, safeguarded, and traceable; every gage must carry a unique, permanent identifier that links the measurement to a calibration record.
The M&TE master list (gage register) is the control document: it holds the unique ID, description, range, resolution, tolerance, owning department, location, calibration interval, last and next calibration dates, and current status for every controlled instrument.
A gage whose calibration due date has passed is out of service by definition -- there is no grace period. It must be red-tagged, returned to the gage crib, and cannot be restored by an informal shop check against a setting master.
Instruments used only for indication (tool-setting, coolant temperature, go/no-go presence checks) may be excluded from recall only if they are permanently labeled Calibration Not Required / For Reference Only and are never used to accept product.
Customer-supplied M&TE is customer property under ISO 9001 clause 8.5.3: it must be verified and identified on receipt, safeguarded and segregated from company assets, kept calibrated per the contract, and any loss, damage, or unsuitability must be reported to the customer in writing.
Last updated: September 2026
- 8.5 M&TE Identification, Control, and Customer-Supplied Equipment
- Why Gage Control Is a Separate Discipline from Calibration
Section 8.3 covered how an instrument is calibrated and how traceability to national standards is established. Calibration alone, however, proves nothing about the parts on the shipping dock. A calibration certificate is only useful if a quality technician can answer three questions on demand during a customer or registrar audit:
Which physical instrument produced the number written on this inspection record?
Was that instrument inside its calibration interval on the date the measurement was taken?
Where is that instrument now , and has anything happened to it since?
Answering those questions requires a Measurement and Test Equipment (M&TE) control system — identification, a master list, a recall mechanism, status labeling, and handling rules. ISO 9001:2015 clause 7.1.5 (Monitoring and Measuring Resources) states the requirement plainly: measuring equipment must be identified in order to determine its status, and it must be safeguarded from adjustments, damage, or deterioration that would invalidate its calibration status. AS9100D and IATF 16949 add stricter documentation and reverse-traceability expectations on top of the same clause.
Unique Identification of M&TE
Every controlled instrument carries a unique identifier that is never reused, even after the instrument is scrapped. Two identical 0-1" micrometers bought on the same purchase order are different pieces of M&TE with different histories.
Identifier Schemes
A workable ID scheme is short, human-readable, and machine-scannable. Common patterns:
Scheme Example Notes
Sequential MT-04821 Simplest; carries no meaning, which avoids re-numbering when equipment moves between departments.
Type-prefixed MIC-0112 , CAL-0087 , TRQ-0034 Human-readable at a glance; breaks down if an instrument is re-purposed.
Department-coded QA-CMM-03 , WELD-TRQ-11 Convenient for physical audits; must be re-issued if the asset transfers, which creates history gaps.
Serial-number-based Manufacturer serial as the ID Guarantees uniqueness; long, and fails for instruments with no serial number (gage blocks, pin sets).
Marking Methods and the Cardinal Marking Rule
Vibro-etch / electro-chemical etch : permanent, low-cost, standard for steel frames and gage bodies.
Laser marking : permanent, precise, suitable for carbide and hardened surfaces.
Bar-code or QR labels : fast check-in/check-out, but labels peel in coolant and solvent environments; use as a supplement to a permanent mark, not a replacement.
RFID tags : used on large assets (CMMs, surface plates, torque testers) and in tool cribs with automated dispensing.
Small-item alternatives : gage blocks, pin gages, thread gages, and weight sets are controlled as a set with the ID on the case, plus a case inventory sheet listing each element.
Caution
Never mark a measuring surface. Identification marks must not be applied to anvils, spindle faces, gaging surfaces, reference planes, or the wringing faces of gage blocks. Stamping an ID on a micrometer anvil destroys the instrument; etching an ID onto the gaging diameter of a plug gage changes its size and its wear pattern.
The M&TE Master List (Gage Register)
The master list is the single source of truth for what is under calibration control. During an audit it is the first document requested, and it is the document the auditor samples from when performing forward tracing.
- Field Purpose Auditor's question it answers
- Unique ID Links the instrument to records "Show me the history of gage MIC-0112."
Description / manufacturer / model / serial Identifies the physical asset "Is this the instrument the certificate covers?"
Range and resolution Confirms fitness for the characteristic "Was a 0.001" caliper appropriate for a 0.004" tolerance?"
- Accuracy / tolerance limits Defines pass/fail at calibration "What does out-of-tolerance mean for this gage?"
- Owning department and physical location Enables physical verification and recall "Bring me this instrument."
- Calibration interval Drives the recall schedule "Why is this gage on a 12-month cycle?"
- Last calibration date / next due date Establishes in-service validity "Was it in calibration on 14 March?"
Calibration source (internal lab, external lab, accreditation) Establishes the traceability chain "Is the external lab ISO/IEC 17025 accredited for this parameter?"
Current status Active, limited, reference-only, out for calibration, quarantined, retired "Where is gage TRQ-0034 right now?"
The master list is a controlled record . It is reconciled against a physical inventory at a defined frequency (annually is typical, quarterly in aerospace), and the reconciliation itself is recorded — a list with no physical verification behind it is a finding waiting to happen.
The Calibration Recall System
The recall system is the mechanism that converts the master list into shop-floor action. GAGE CONTROL LOOP:
- [ New gage received ]
- |
- v
- [ Incoming verification: damage, function, initial calibration ]
- |
- v
- [ Assign unique ID + add to master list + apply status label ]
- |
- v
- [ Issue to user / gage crib checkout ] <-------------------+
- | |
- v |
- [ In service: daily user checks, PM, handling rules ] |
- | |
- +--> [ Damage / suspect reading ] --> [ Red tag ] --+ |
- | | |
- v v |
- [ Recall report: due within 30 days ] [ Calibration lab ]
- | As-Found / As-Left
- v |
- [ Recall notice to owner; gage returned ]-----------------+
- |
- v
- [ Past due? -> OUT OF SERVICE, red tag, impact assessment (8.4) ]
- |
- v
- [ Beyond economic repair -> retire, remove ID, purge from list ]
- Operating Rules a Technician Must Know
The recall report runs ahead of the due date , typically 30 days, so the owning department can plan a replacement instrument before production is interrupted.
There is no grace period. The instant the due date passes, the instrument is out of service. "It was only three days over and it still checks good" is not a defense; it triggers the out-of-calibration impact assessment described in Section 8.4.
Checkout/check-in at the gage crib creates the possession record that makes reverse traceability possible. An instrument signed out to a shift and never returned is a suspect instrument.
Never repair or adjust a controlled gage on the shop floor. Zeroing a micrometer against its setting standard is a permitted user check; opening the frame, adjusting an internal stop, or re-setting a torque wrench's internal scale is an unauthorized adjustment that voids the calibration status.
Personal tools require the same control. If a machinist's own caliper is used to accept product, it must be identified, listed, calibrated, and recalled exactly like company equipment — or the shop must prohibit personal tools from being used for acceptance at all. Write the policy down; auditors ask.
Status Classes on the Master List
Status Meaning Product acceptance allowed?
Active / In calibration Within interval, full range certified Yes
Limited calibration Certified only over part of its range, or with a stated correction Yes, but only within the stated restriction, which must be on the label
Calibration Not Required (CNR) / For Reference Only Deliberately excluded from recall No — indication only (tool setting, coolant temperature, presence checks)
Out for calibration Physically at the lab No
Quarantined / Red tag Failed calibration, damaged, or suspect No — and it triggers a reverse-traceability review
Retired Permanently removed; ID never reissued No
Important
The CNR trap : Labeling an instrument "Calibration Not Required" does not make the problem go away — it makes a commitment . If an auditor finds a CNR-labeled dial indicator being used to buy off a print dimension, the finding is usually escalated to major , because the organization has documented that it knowingly excluded from control an instrument it then used for acceptance.
Handling, Storage, and Maintenance of M&TE
Calibration certifies an instrument at a point in time; handling determines whether that certification survives to the next due date.
Instrument family Routine maintenance Storage requirement
Micrometers, calipers Wipe anvils and jaws, check zero against the setting standard each shift, light oil film on non-gaging surfaces Closed case, jaws/anvils slightly open, away from coolant mist
Dial and test indicators Check free travel and return-to-zero, replace damaged contact points Stem unloaded, case stored flat, no stacked weight
Gage blocks Clean and re-oil after use; never leave wrung Dedicated case, controlled humidity, blocks separated
Plug, ring, and thread gages Inspect for wear scoring, re-oil, watch wear-allowance limits Individual sleeves or foam cutouts, no gage-on-gage contact
Torque wrenches Return click-type wrenches to their lowest scale setting; never use as a breaker bar Padded drawer, never dropped
Surface plates Clean with plate cleaner, cover when idle, periodic repeatability check On isolated stand, level, no parts stored on the surface
CMMs Air filter/dryer checks, probe qualification, artifact check on a schedule Environmentally controlled room, restricted access
Damage reporting is mandatory and non-punitive. A dropped micrometer that is quietly put back in the drawer is the single most common origin of a large reverse-traceability investigation. Shops that discipline technicians for reporting drops end up with unreported drops.
Customer-Supplied M&TE
Customers routinely furnish gages so that the supplier's measurement matches the customer's own: functional check fixtures, master gages, attribute go/no-go gages for a specific program, and calibrated test stands. Under ISO 9001:2015 clause 8.5.3 (Property Belonging to Customers or External Providers) , this equipment is customer property , and the supplier's obligations are specific.
The Six Required Controls
# Control What the technician actually does
1. Verify on receipt Confirm the item matches the shipping/contract documentation, is undamaged, and is functional Inspect for shipping damage, confirm serial number and revision level against the contract
2. Confirm calibration status Determine whether a valid calibration certificate accompanied the gage and whether it is still in date Check the certificate date, the accreditation of the issuing lab, and the stated uncertainty
3. Identify as customer property Mark or tag the item so it cannot be confused with company assets Apply a distinct customer-property tag plus the internal M&TE ID; add it to the master list flagged as customer-owned
4. Safeguard and segregate Protect it from loss, damage, and unauthorized use Dedicated, controlled storage; issue only to trained users on the specific program
5. Maintain and recalibrate per contract Keep it fit for use throughout the contract Put it on the recall schedule at the interval the contract (or the customer's own procedure) specifies
6. Report problems in writing Report loss, damage, deterioration, or unsuitability for use to the customer Raise a written notification and retain the record; do not attempt repair without written authorization
The Two Questions That Decide Everything
Who calibrates it? The default assumption that "the customer sent it, so the customer maintains it" is wrong far more often than technicians expect. Unless the contract or quality clause explicitly assigns calibration to the customer, the supplier is responsible for ensuring the gage is in calibration before it is used to accept product . If the contract is silent, get it in writing before the first part is measured.
What if it does not work? A customer-supplied check fixture that fails a repeatability study, or arrives out of calibration, must be reported to the customer , and product may not be accepted with it in the meantime. Quietly substituting a company gage "because it measures the same thing" defeats the reason the customer supplied the fixture and is a classic second-party audit finding.
Note
Customer-supplied M&TE vs. customer-supplied material : Both fall under clause 8.5.3, and both require identification, safeguarding, and written notification of loss or damage. The difference is that customer-supplied equipment additionally enters the calibration control system, while customer-supplied material enters the incoming-inspection and traceability system. A technician who confuses the two will safeguard a master gage but forget to put it on the recall schedule.
Worked Scenario: The Unlisted Bore Gage
Situation : During a second-party audit, a customer auditor watches a technician measure a bore with a dial bore gage that carries a current calibration sticker reading BG-221, due 2026-11-30 . The auditor asks to see BG-221 on the M&TE master list. It is not there. The gage was transferred from a sister plant eighteen months ago, calibrated by the external lab under its old plant ID, and never added to the receiving plant's register.
Analysis :
The instrument itself is calibrated and traceable — the measurement is probably sound.
The system is not: the gage is not on any recall report, so nothing would have prevented it from going overdue; nobody owns it; and reverse traceability from a future out-of-tolerance finding would fail because there is no record linking the gage to jobs.
Correct classification and response : This is a systemic control failure , not a measurement failure. Expect a nonconformance against ISO 9001 clause 7.1.5. The response is to add the gage to the master list with the correct interval, reconcile the full physical inventory against the list to find other unlisted instruments, and add a transfer-in step to the gage control procedure. Arguing that "the sticker was current, so there is no problem" misses the finding entirely.
Common Exam Traps for CQT Candidates
Caution
Trap 1: "It checks good against the master." An informal bench comparison never restores calibration status on an overdue instrument. Only a documented calibration by the authorized source does.
Trap 2: Confusing the label with the system. A current sticker proves calibration; the master list proves control . Auditors test the second by sampling the list and asking for the tool, and by sampling the shop floor and asking for the list entry.
Trap 3: Assuming the customer calibrates customer-supplied gages. Responsibility follows the contract. If the contract is silent, the supplier must ensure the gage is calibrated before using it to accept product.
Trap 4: Handling loss or damage of customer property informally. A verbal mention to the buyer is not notification. Clause 8.5.3 requires the report to the customer to be recorded.
Trap 5: Treating "Reference Only" as a way to reduce calibration workload. It is permitted only for instruments that genuinely never accept product. Using one for acceptance converts a paperwork shortcut into a major nonconformance.