Study guide
10.3 Form and Orientation Controls in GD&T
ASQ Certified Quality Technician CQT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Quality Philosophies, Principles, and Management Systems
1.1 Quality Philosophies & Pioneers 1.2 Quality Management Systems, Standards & Documentation 1.3 Customer-Supplier Relationships & Quality Culture
2 Chapter 2: Cost of Quality, Teams, and Professional Ethics
2.1 Cost of Quality (COQ) & Economic Trade-Offs 2.2 Quality Improvement Teams & Meeting Management 2.3 Professional Conduct & ASQ Code of Ethics
3 Chapter 3: Basic Quality Tools & Continuous Improvement
3.1 Process Mapping, Flowcharts, and SIPOC 3.2 Cause-and-Effect Analysis & Check Sheets 3.3 Pareto Analysis & Prioritization 3.4 Histograms & Scatter Diagrams
4 Chapter 4: Descriptive Statistics and Probability Distributions
4.1 Data Types, Sampling Methods, and Populations 4.2 Measures of Central Tendency and Dispersion 4.3 Normal Distribution & Z-Score Calculations 4.4 Discrete Distributions: Binomial, Poisson, and Hypergeometric
5 Chapter 5: Statistical Process Control (SPC) Fundamentals & Variables Charts
5.1 SPC Fundamentals & Process Variation 5.2 Control Limits vs. Specification Limits 5.3 X-bar and R Charts 5.4 X-bar & s Charts and Individual-Moving Range (I-MR) Charts
6 Chapter 6: Attributes Control Charts and Out-of-Control Patterns
6.1 Control Charts for Nonconforming Units: p and np Charts 6.2 Control Charts for Nonconformities: c and u Charts 6.3 Out-of-Control Rules & Process Analysis
7 Chapter 7: Process Capability and Performance Analysis
7.1 Process Stability Prerequisite & Capability Basics 7.2 Potential Capability (Cp) and Actual Capability (Cpk) 7.3 Process Performance (Pp, Ppk) and Long-Term vs. Short-Term Variation 7.4 One-Sided Tolerances and PPM Defect Calculations
8 Chapter 8: Metrology Fundamentals, Standards, and Calibration
8.1 Metrology Foundations & Environmental Controls 8.2 Precision Gage Blocks & Standards Hierarchy 8.3 Calibration Systems & NIST Traceability 8.4 Out-of-Calibration Procedures & Reverse Traceability 8.5 M&TE Identification, Control, and Customer-Supplied Equipment
9 Chapter 9: Measurement Instruments and Measurement System Analysis (Gage R&R)
9.1 Common Dimensional Hand Measuring Instruments 9.2 Fixed Gages, Optical Comparators, and CMM Systems 9.3 Measurement System Analysis: Bias, Linearity, and Stability 9.4 Variable Gage R&R: Repeatability and Reproducibility 9.5 Electronic, Weighing, and Force Measurement Equipment
10 Chapter 10: Technical Drawings, Tolerancing, and GD&T (ASME Y14.5)
10.1 Engineering Drawing Basics & Projection Methods 10.2 Datums and the Datum Reference Frame 10.3 Form and Orientation Controls in GD&T 10.4 Location, Profile, and Runout Controls with Modifiers 10.5 Classification of Product Characteristics and Defects
11 Chapter 11: Inspection Planning, Sampling Plans, and Material Disposition
11.1 Inspection Planning & Inspection Points 11.2 Acceptance Sampling & ANSI/ASQ Z1.4 11.3 Switching Rules & Variables Sampling (Z1.9) 11.4 Nonconforming Material Control & MRB Dispositions 11.5 Types of Measurements, Unit Conversion, and Rounding Rules
12 Chapter 12: Quality Audits
12.1 Quality Auditing Principles & Types 12.2 The Audit Process: Planning, Performance, and Reporting 12.3 Audit Tools and Techniques
13 Chapter 13: Risk Management, Corrective and Preventive Action, and Safety
13.1 Risk Assessment Inputs, Monitoring, and Control Plans 13.2 FMEA, Action Priority, and Technician Workplace Safety 13.3 Root Cause Analysis & Problem-Solving 13.4 Corrective and Preventive Action (CAPA) & Verification 13.5 Preventive Action, Mistake-Proofing, and Read-Across
10.3 Form and Orientation Controls in GD&T
Key Takeaways Explain This Topic AI
Form controls (Straightness, Flatness, Circularity, Cylindricity) govern individual features and are strictly prohibited from referencing datums.
ASME Rule #1 (Envelope Principle) mandates that where only a size tolerance is specified, the limits of size prescribe the boundary of perfect form at Maximum Material Condition (MMC); form error cannot exceed size tolerance unless an axis straightness override applies.
Orientation controls (Perpendicularity, Parallelism, Angularity) govern related features and always require at least one datum reference to establish angular orientation.
Straightness can control either surface line elements (2D planar tolerance zone) or derived median line / axis (cylindrical tolerance zone allowing MMC modifier), whereas Cylindricity is a 3D composite form control simultaneously governing circularity, straightness, and taper.
The Tangent Plane modifier (circled T) in an orientation callout inspects the plane contacting the highest peaks of the surface rather than the peak-to-valley envelope, preventing surface micro-waviness from falsely rejecting functional mating surfaces.
Last updated: September 2026
- 10.3 Form and Orientation Controls in GD&T
- Overview of the 14 Geometric Characteristics
Geometric Dimensioning and Tolerancing (GD&T) under ASME Y14.5 organizes geometric variations into five functional categories encompassing 14 geometric characteristics . Each characteristic controls a specific aspect of part geometry, utilizing standardized symbols displayed inside a Feature Control Frame.
- Category Geometric Characteristic Symbol Description Datum Reference Required? Tolerance Zone Shape
- FORM Straightness Single horizontal line (—) NEVER 2 parallel lines or Cylinder ( ∅ \varnothing ∅ )
- FORM Flatness Parallelogram (▱) NEVER 2 parallel planes
- FORM Circularity (Roundness) Circle (○) NEVER 2 concentric coplanar circles
- FORM Cylindricity Circle inside two parallel lines (⌭) NEVER 2 coaxial cylinders
ORIENTATION Perpendicularity Inverted 'T' (⟂) ALWAYS (1 to 3) 2 parallel planes or Cylinder ( ∅ \varnothing ∅ )
ORIENTATION Parallelism Two slanted parallel lines (//) ALWAYS (1 to 3) 2 parallel planes or Cylinder ( ∅ \varnothing ∅ )
ORIENTATION Angularity Acute angle (∠) ALWAYS (1 to 3) 2 parallel planes or Cylinder ( ∅ \varnothing ∅ )
LOCATION Position (True Position) Crosshair inside circle (⌖) ALWAYS (1 to 3) Cylinder ( ∅ \varnothing ∅ ) or 2 parallel planes
- LOCATION Concentricity Two concentric circles (◎) ALWAYS (1 to 3) Cylinder ( ∅ \varnothing ∅ )
- LOCATION Symmetry Three horizontal bars (⌯) ALWAYS (1 to 3) 2 parallel planes
- PROFILE Profile of a Surface Semicircle with flat base (⌓) Usually (0 to 3) 2 profile envelope surfaces
- PROFILE Profile of a Line Curved arc (⌒) Usually (0 to 3) 2 profile envelope lines
- RUNOUT Circular Runout Single diagonal arrow (↗) ALWAYS (1 to 2) 2 coplanar circles / radial indicator
- RUNOUT Total Runout Two joined diagonal arrows (⇗) ALWAYS (1 to 2) 2 coaxial cylinders / traversing indicator
Important
The Cardinal Rule of Form Controls :
Form controls apply strictly to individual features . They control the shape of a single surface or line element independently. Therefore, Form controls NEVER reference a datum ! Placing a datum reference inside a feature control frame for straightness, flatness, circularity, or cylindricity is a severe drafting error and an immediate red flag on the ASQ CQT exam.
ASME Rule #1: The Envelope Principle (Taylor Principle)
A foundational concept tested extensively on the ASQ CQT examination is ASME Rule #1 (often called the Envelope Principle or the Taylor Principle of Perfect Form at MMC ):
Important
ASME Y14.5 Rule #1 : Where only a tolerance of size is specified, the limits of size of an individual feature of size prescribe the extent within which variations of geometric form, as well as size, are allowed. Specifically:
The surface or surfaces of an individual feature of size shall not extend beyond a boundary (envelope) of perfect form at Maximum Material Condition (MMC) .
Where the feature of size is produced at its MMC limit, its form must be theoretically perfect (zero straightness, flatness, or circularity error allowed).
As the actual produced size departs from MMC toward Least Material Condition (LMC), form errors are permitted, but form error can never exceed the total size tolerance spread. RULE #1 ENVELOPE PRINCIPLE (SHAFT AT MMC VS. LMC):
Case 1: Shaft produced at MMC (Largest Allowable Diameter = 1.005"):
- +---------------------------------------+
- | Perfect Form Required! Straightness=0 |
- +---------------------------------------+
- Envelope Boundary = 1.005" (Must pass through 1.005" perfect ring gage!)
Case 2: Shaft produced at LMC (Smallest Allowable Diameter = 0.995"):
- /~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\
- / Cambered / Bent Shaft \
- \~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~/
- Form variation (bowing/straightness error) of up to 0.010" is permitted,
provided no portion violates the 1.005" MMC boundary!
The Form Tolerance Rule
Because Rule #1 dictates that size limits control form, any form tolerance explicitly called out on a drawing must be smaller (tighter) than the total size tolerance spread . For example, if a plate thickness is specified as 0.500 " ± 0.010 " 0.500" \pm 0.010" 0.500" ± 0.010" (total tolerance = 0.020 " = 0.020" = 0.020" ), a surface flatness callout of 0.025 " 0.025" 0.025" is metrologically meaningless, because Rule #1 already restricts form error to 0.020 " 0.020" 0.020" !
Overriding Rule #1
Rule #1 applies automatically unless explicitly overridden by:
The Independency Symbol ( I ◯ \textcircled{I} I ◯ ) placed next to the size dimension.
Parts subject to Free State Variation (non-rigid sheet metal, rubber, thin plastics).
An Axis Straightness callout with a Maximum Material Condition modifier ( M ◯ \textcircled{M} M ◯ ). This allows axis straightness to exceed the size tolerance, creating a Virtual Condition boundary.
- Form Controls: Individual Geometric Characteristics
- 1. Straightness
Straightness evaluates whether a line element or centerline is a straight line. Under ASME Y14.5, straightness operates in two distinct modes: SURFACE STRAIGHTNESS VS. AXIS STRAIGHTNESS:
SURFACE ELEMENT STRAIGHTNESS: AXIS (DML) STRAIGHTNESS:
Applied to surface line elements; Applied to feature of size diameter;
Tolerance zone = 2 Parallel Lines: Tolerance zone = CYLINDRICAL (DIA t):
- Line Element Derived Median Line
- -------------------- - - - - - - - - - - - - - - - - -
- ===================== (Tolerance t) ================================= (DIA t)
- -------------------- - - - - - - - - - - - - - - - - -
- No Datums! No Modifiers! - May include MMC modifier (M)!
- Must be less than size tolerance! - Overrides Rule #1!
Surface Element Straightness : The leader points directly to the surface view. The tolerance zone is two parallel straight lines separated by tolerance t t t lying in the cutting plane. Every longitudinal line element of the surface must lie between these lines. No datums and no material modifiers are permitted.
Axis (Derived Median Line - DML) Straightness : The feature control frame is placed directly beneath the diameter size dimension and includes the diameter symbol (e.g., [ − ∣ ∅ 0.002 ∣ M ◯ ] [\, - \mid \varnothing 0.002 \mid \textcircled{M} \,] [ − ∣ ∅ 0.002 ∣ M ◯ ] ). The tolerance zone is a cylinder of diameter ∅ t \varnothing t ∅ t within which the derived median line of the shaft must lie. This control allows the MMC modifier, which overrides Rule #1 and grants bonus tolerance!
2. Flatness
Flatness evaluates whether all points on a surface lie within a single plane.
Tolerance Zone : Bounded by two parallel planes separated by the specified distance t t t .
Inspection Methodology : The part is supported on a granite surface plate on three adjustable leveling jacks . A dial test indicator is moved across the jacks, and the jacks are adjusted until the indicator reads zero at all three support points (leveling the reference plane). The indicator is then swept across the entire surface. The difference between the highest positive reading and lowest negative reading—the Full Indicator Movement (FIM) —must not exceed the flatness tolerance t t t .
Derived Median Plane Flatness : When applied to a planar feature of size (e.g., the width of a bar), flatness controls the median plane rather than the exterior surface.
3. Circularity (Roundness)
Circularity is a two-dimensional form control that evaluates the roundness of individual cross-sections.
Tolerance Zone : In each individual cross-sectional plane perpendicular to the axis, all points of the circumferential contour must lie between two concentric coplanar circles whose radial separation is t t t ( R outer − R inner = t R_{\text{outer}} - R_{\text{inner}} = t R outer − R inner = t ).
Critical Metrological Fact : Circularity applies independently to each discrete cross-section along the length of a cylinder or cone. It evaluates ovality and multi-lobed shapes on that single slice, but does not control taper or straightness across the length.
4. Cylindricity
Cylindricity is a three-dimensional composite form control that evaluates the entire cylindrical surface simultaneously.
Tolerance Zone : Bounded by two coaxial cylinders whose radial separation is t t t ( R outer − R inner = t R_{\text{outer}} - R_{\text{inner}} = t R outer − R inner = t ).
Composite Control : Cylindricity simultaneously controls:
- Circularity (roundness of every cross-section)
- Straightness of all longitudinal surface elements
- Parallelism of surface elements (preventing taper, hourglass, and barrel forms)
Rule : Cylindricity tolerance must be tighter than half the diametral size tolerance ( t < USL − LSL 2 t < \frac{\text{USL} - \text{LSL}}{2} t < 2 USL − LSL ).
Technical Attribute Circularity (Roundness) Cylindricity
Dimensional Scope 2D Control (Individual radial cross-sections) 3D Control (Entire cylindrical surface simultaneously)
Tolerance Zone Shape Two concentric coplanar circles Two coaxial cylinders
Taper / Barrel Detection Cannot detect taper between different slices Detects taper, barrel, and hourglass distortion
Straightness Control Does not control longitudinal straightness Simultaneously controls surface line straightness
Inspection Complexity Moderate (Rotary table or V-block slice) High (Precision CMM or continuous spindle profilometer)
Orientation Controls: Related Geometric Characteristics
Orientation controls evaluate the angular orientation of features relative to datums. Unlike form controls, orientation controls ALWAYS require at least one datum reference (and can reference up to three datums). THE THREE ORIENTATION CONTROLS:
1. PERPENDICULARITY (90 deg to Datum): 2. PARALLELISM (0 deg to Datum):
Tolerance Zone = 2 Parallel Planes: Tolerance Zone = 2 Parallel Planes:
- | | -----------------------------
- | | <-- Tolerance Zone (t) ============================= (t)
- | | -----------------------------
- ====================== [Datum Plane A] ============================= [Datum Plane A]
------------------------------------------------------------------------------------
3. ANGULARITY (Basic Angle theta to Datum): 4. TANGENT PLANE MODIFIER (Circled T):
Tolerance Zone = 2 Planes at Angle theta: Inspects plane contacting peaks;
depressions/valleys are ignored!
- / /
- / / <-- Tolerance Zone (t) /------------/ Tangent Plane
- / / Angle = Basic [theta] * * * High peaks
- +---------------------- [Datum A] ~~~~~~V~~~~~~~V~~ Surface waviness
- 1. Perpendicularity
Controls a surface, center plane, or axis at exactly 90 ∘ 90^\circ 9 0 ∘ relative to a datum reference.
Planar Surface Perpendicularity : Tolerance zone is bounded by two parallel planes separated by distance t t t , perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) to the datum plane.
Axis Perpendicularity (Pin or Hole) : When the diameter symbol ( ∅ \varnothing ∅ ) precedes the tolerance value (e.g., [ ⊥ ∣ ∅ 0.005 ∣ A ] [\, \perp \mid \varnothing 0.005 \mid \mathbf{A} \,] [ ⊥∣ ∅ 0.005 ∣ A ] ), the tolerance zone is a cylinder of diameter ∅ t \varnothing t ∅ t perpendicular to the datum plane. The centerline of the pin or bore must lie entirely inside this cylinder.
2. Parallelism
Controls a surface, center plane, or axis equidistant at all points ( 0 ∘ 0^\circ 0 ∘ ) relative to a datum reference.
Planar Surface Parallelism : Tolerance zone is bounded by two parallel planes separated by distance t t t , oriented parallel to the datum plane.
Axis Parallelism : Tolerance zone can be two parallel planes or a cylindrical zone parallel to the datum axis.
3. Angularity
Controls a surface, center plane, or axis at a specified angle (other than 0 ∘ 0^\circ 0 ∘ or 90 ∘ 90^\circ 9 0 ∘ ) relative to one or more datums.
Basic Angle Requirement : The specified angle on the drawing must be a Basic Dimension (enclosed in a rectangle, e.g., [ 30 ∘ ] [30^\circ] [ 3 0 ∘ ] or [ 45 ∘ ] [45^\circ] [ 4 5 ∘ ] ). Basic dimensions have zero direct tolerance; the allowable variation is defined solely by the feature control frame.
Tolerance Zone : Two parallel planes separated by distance t t t , oriented at the exact basic angle to the datum.
The Tangent Plane Modifier ( T ◯ \textcircled{T} T ◯ )
When inspecting orientation on a machined surface with significant micro-roughness or shallow tooling marks, a standard dial indicator registers every microscopic peak and valley, potentially rejecting a functionally flat mating face.
To solve this, ASME Y14.5 provides the Tangent Plane modifier (a circled capital T : T ◯ \textcircled{T} T ◯ ) placed after the tolerance value in an orientation feature control frame (e.g., [ / / ∣ 0.002 T ◯ ∣ A ] [\, // \mid 0.002 \textcircled{T} \mid \mathbf{A} \,] [ // ∣ 0.002 T ◯ ∣ A ] ).
Metrological Effect : The tolerance zone applies only to the theoretical plane contacting the highest three peaks of the surface . Surface depressions, pits, and valleys are completely ignored. This ensures functional fit for mating gasket faces and bolted flanges.
Dial Indicator Inspection: The Three-Lobe Out-of-Roundness Trap
A frequent and critical topic on the ASQ CQT examination is the detection of lobed out-of-roundness on centerless-ground shafts. THE THREE-LOBE REULEAUX TRIANGLE INSPECTION TRAP:
TWO-POINT MICROMETER MEASUREMENT: V-BLOCK & DIAL INDICATOR MEASUREMENT:
Opposing anvils measure chordal width: Part supported in 60-degree V-Block:
- Anvil Dial Indicator
- v v
- +-----+ +-----+
- / * \ / * \
| * * | Constant Diameter! | * * | Needle FLUCTUATES!
\ * / Micrometer reads identical \ * / Lobing immediately
+-----+ dimension at every angle! \ === / detected!
- ^ \ / <-- 60 deg V-Block
- Anvil \ /
- Why Two-Point Hand Tools Fail
When cylindrical parts are manufactured using centerless grinding, chatter and irregular workpiece rotation frequently produce odd-numbered lobed profiles (most commonly 3-lobe or 5-lobe geometries, geometrically known as Reuleaux polygons):
An odd-lobed profile has the unique geometric property of constant diametral width across any two opposing 180 ∘ 180^\circ 18 0 ∘ points.
If an inspector uses a standard two-point measuring tool (such as an outside micrometer, vernier caliper, or dial snap gage), the reading will be completely identical at every rotational angle !
The technician mistakenly concludes the shaft is perfectly round, yet the part exhibits severe circularity error that will cause bearing seizure in high-speed assemblies!
The Correct Inspection Setup
To detect odd-lobed circularity defects, the technician must use an inspection method that measures radial variation relative to a center origin :
Precision Rotary Spindle Roundness Gage : The part is mounted on an ultra-precise air-bearing turntable and swept by an electronic stylus, plotting true radial deviation.
V-Block Inspection : The shaft is placed in a precision-ground 60 ∘ 60^\circ 6 0 ∘ V-block (for 3-lobe parts) or 108 ∘ 108^\circ 10 8 ∘ V-block (for 5-lobe parts) on a granite surface plate, and a dial test indicator contacts the top of the shaft. As the shaft rotates, the lobes ride up and down the V-block inclined walls, magnifying the radial runout so the indicator needle fluctuates dramatically, immediately exposing the out-of-roundness.
Step-by-Step Worked Inspection Example: Surface Flatness Verification
Scenario:
A quality technician must verify the flatness of a precision-ground tool steel fixture plate measuring 8.00 " × 6.00 " 8.00" \times 6.00" 8.00" × 6.00" . The drawing feature control frame states: [ Flatness ∣ 0.0015 ] [\, \text{Flatness} \mid 0.0015 \,] [ Flatness ∣ 0.0015 ]
Step 1: Set Up the Surface Plate Inspection
The technician thoroughly stones and cleans a Grade A granite surface plate with surface cleaner.
The fixture plate is placed on three adjustable precision leveling jacks (Jack 1, Jack 2, Jack 3) forming the largest possible triangle on the underside of the part.
A sensitive lever-type dial test indicator ( 0.0001 " 0.0001" 0.0001" discrimination) is mounted on a heavy transfer stand.
Step 2: Establish the Parallel Reference Plane
The technician positions the indicator stylus directly over Jack 1 and rotates the dial bezel to read 0.0000 " 0.0000" 0.0000" .
The indicator is slid across to Jack 2; Jack 2 is mechanically adjusted until the indicator reads 0.0000 " 0.0000" 0.0000" .
The indicator is slid to Jack 3; Jack 3 is adjusted until the indicator reads 0.0000 " 0.0000" 0.0000" .
The technician sweeps back across Jack 1, 2, and 3 to confirm all three read exactly 0.0000 " 0.0000" 0.0000" .
Metrological Purpose : This three-point leveling procedure removes all part tilt relative to the granite plate, establishing the granite surface plate as the parallel reference datum.
Step 3: Traverse the Surface and Record Indicator Extremes
The technician traverses the indicator across the entire top surface of the plate in an overlapping grid pattern, monitoring the dial pointer:
- Maximum Positive Peak Reading ( R max R_{\max} R m a x ) : + 0.0007 " +0.0007" + 0.0007"
- Minimum Negative Valley Reading ( R min R_{\min} R m i n ) : − 0.0005 " -0.0005" − 0.0005"
Step 4: Calculate Full Indicator Movement (FIM) Actual Flatness Error (FIM) = R max − R min = ( + 0.0007 " ) − ( − 0.0005 " ) = 0.0012 " \text{Actual Flatness Error (FIM)} = R_{\max} - R_{\min} = (+0.0007") - (-0.0005") = \mathbf{0.0012"} Actual Flatness Error (FIM) = R m a x − R m i n = ( + 0.0007" ) − ( − 0.0005" ) = 0.0012"
- Step 5: Conformance Evaluation
- Drawing Tolerance: 0.0015 " 0.0015" 0.0015"
- Observed Flatness Error: 0.0012 " 0.0012" 0.0012"
Since 0.0012 " ≤ 0.0015 " 0.0012" \le 0.0015" 0.0012" ≤ 0.0015" , the plate conforms to the engineering drawing specification (PASS).
- Technician Inspection Scenarios & Common Exam Traps
- Real-World Shop Scenario: Vise-Induced Flatness Failure
A milling machine operator faces a precision aluminum manifold plate. With the part clamped tightly in a hydraulic milling vise, the operator sweeps a dial indicator across the face and observes a near-perfect flatness reading of 0.0003 " 0.0003" 0.0003" . The operator releases the vise and sends the part to the quality lab. In the temperature-controlled lab, the quality technician sets the manifold on three leveling jacks and measures a flatness error of 0.0035 " 0.0035" 0.0035" , rejecting the part! Why did this occur?
Root Cause Analysis : The clamping force of the hydraulic vise elastically deformed (pinched and bowed) the aluminum plate during machining. While clamped, the cutter faced a flat plane. As soon as the vise jaws were released, the plate sprang back to its unstressed state, revealing severe concave warpage ( machining clamp stress springback ). Inspection must always be conducted in the free, unclamped state unless a specific restrained-condition note appears on the print!
Common Exam Traps for CQT Candidates
Exam Trap 1: Datums in Form Feature Control Frames : Form controls (Straightness, Flatness, Circularity, Cylindricity) NEVER have datums. If an exam question displays [ Flatness ∣ 0.002 ∣ A ] [\, \text{Flatness} \mid 0.002 \mid \mathbf{A} \,] [ Flatness ∣ 0.002 ∣ A ] and asks what is wrong, the answer is: "Form controls are not permitted to reference datums."
Exam Trap 2: Circularity versus Cylindricity : Circularity is a 2D slice control ; it cannot detect taper along the length of a cylinder. Cylindricity is a 3D composite control that captures circularity, straightness, and taper simultaneously.
Exam Trap 3: Two-Point Checks for Roundness : A two-point outside micrometer cannot detect odd-lobed out-of-roundness (such as a 3-lobed Reuleaux profile). Detecting lobing requires a V-block or precision rotary spindle.
Exam Trap 4: Tangent Plane Modifier : The circled T ( T ◯ \textcircled{T} T ◯ ) modifier indicates that orientation tolerance applies to the theoretical plane contacting the high points of the surface, ignoring internal surface pits and valleys.