Study guide

11.1 ASSE Series 5000 and 5110 Professional Qualifications

ASSE 5110 Backflow Prevention Assembly Tester Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About ASSE 5110 and the Series 5000 Program 1.2 Eligibility, 40-Hour Course, Written & Practical Format 1.3 Validity, Recertification, and Retake Rules

2 Hydraulics Fundamentals

2.1 Pressure, Head, and Atmospheric Reference 2.2 Static vs Flowing Conditions for Testers 2.3 PSID and How Differentials Are Measured

3 Backpressure, Backsiphonage & Differentials

3.1 Backpressure: Causes and Field Examples 3.2 Backsiphonage: Causes and Field Examples 3.3 How Differentials Drive Relief and Air-Inlet Action 3.4 When and Why Backflow Occurs in Distribution Systems

4 Cross-Connection Recognition

4.1 Health Hazard vs Non-Health Hazard Classification 4.2 Common Cross-Connections and Correct Protection 4.3 Containment vs Isolation Strategies

5 RP and DC Assemblies

5.1 RP (ASSE 1013) Components and Operation 5.2 RP Relief Valve Theory and Zone Protection 5.3 DC (ASSE 1015) Components and Operation 5.4 When to Use RP vs DC

6 PVB, SVB & Detector Assemblies

6.1 PVB (ASSE 1020) Components and Operation 6.2 SVB (ASSE 1056) Components and Operation 6.3 RPDA and DCDA Detector Assemblies (1047/1048) 6.4 Non-Testable Devices Testers Must Recognize

7 Test Equipment & Calibration

7.1 Three-Valve Differential Pressure Gauges 7.2 Five-Valve Gauges and Hose Discipline 7.3 Bleeding, Hookup Sequence, and Air Elimination 7.4 Calibration, Accuracy, and Field Verification

8 RP & DC Field Test Procedures

8.1 RP Field Test Procedure (USC 10th Edition) 8.2 RP Pass/Fail Criteria and Troubleshooting 8.3 DC Field Test Procedure 8.4 DC Failures and Common Causes

9 PVB/SVB Tests & Practical Sequence

9.1 PVB Field Test Procedure 9.2 SVB Field Test Procedure 9.3 Comparing the Four Practical-Exam Assemblies 9.4 Hands-On Sequence Under Practical Exam Pressure

10 Installation Requirements & Inspection

10.1 Orientation, Clearance, and Elevation Rules 10.2 RP Drainage, Air Gap, and Flood Protection 10.3 Freeze Protection and Thermal Expansion 10.4 Pre-Test Visual Inspection

11 Codes, Standards & Manuals

11.1 ASSE Series 5000 and 5110 Professional Qualifications 11.2 Device Standards 1013, 1015, 1020, 1056 11.3 USC Manual of Cross-Connection Control 10th Edition 11.4 AWWA M14, EPA 816-R-03-002, and SDWA Framework

12 Reporting, Boundaries & Exam Prep

12.1 Field Test Reports and Pass/Fail Language 12.2 Purveyor Notification and Record Retention 12.3 Tester vs Repairer vs Surveyor Boundaries 12.4 Written Exam Strategy, Study Plan, and Next Credentials

11.1 ASSE Series 5000 and 5110 Professional Qualifications

Key Takeaways Explain This Topic AI

ASSE/IAPMO/ANSI Series 5000 is the Cross-Connection Control Professional Qualifications Standard that defines tester, surveyor, repairer, fire-protection tester, and program-administrator competencies

ASSE 5110 is the personnel qualification for Backflow Prevention Assembly Testers—not a product performance standard

Related Series 5000 credentials include 5120 surveyor, 5130 repairer, 5140 fire protection CCC tester, and 5150 program administrator

Certification is issued through a nationally recognized third-party body using ASSE-approved schools, instructors, and proctors

  • ANSI consensus process strengthens legal and regulatory defensibility when jurisdictions adopt or accept 5110
  • Last updated: August 2026

11.1 ASSE Series 5000 and 5110 Professional Qualifications

Quick Answer: ASSE/IAPMO/ANSI Series 5000 is the national professional qualifications standard for cross-connection control. ASSE 5110 defines the knowledge and hands-on competencies of a Backflow Prevention Assembly Tester . Related credentials— 5120 , 5130 , 5140 , and 5150 —cover survey, repair, fire-protection testing, and program administration. Certification is third-party, delivered through ASSE-approved schools and proctors, and gains legal weight from ANSI consensus adoption.

Why codes and personnel standards matter on this exam

Chapters on hydraulics, assembly internals, and field-test steps teach how to test. This chapter teaches which documents authorize those procedures and which credential proves you are qualified. Written items often pair a device number (10xx product standard) with a personnel number (51xx qualification). Confusing the two is a classic trap. You test hardware built to 1013/1015/1020/1056 . You hold a 5110 credential. Product listings and people credentials are different families.

Series 5000: the professional qualifications umbrella

The full name you should recognize on the exam is the ASSE/IAPMO/ANSI Series 5000 Cross-Connection Control Professional Qualifications Standard . ASSE International (a chapter of IAPMO) develops the series; ANSI recognition means the document went through a consensus process with balanced stakeholder input, public review, and documented responses to comments.

Series 5000 does not tell a manufacturer how to build an RP body or how many psid a relief valve must open at in the laboratory. Those performance rules live in device standards (Chapter 11.2). Series 5000 answers a different question: Who is qualified to test, survey, repair, or administer —and what must that person demonstrate?

  • Credential Role title (common short name) Core scope a 5110 candidate must know
  • 5110 Backflow Prevention Assembly Tester Field-test RP, DC, PVB, SVB; report pass/fail
  • 5120 Cross-Connection Control Surveyor / Specialist Survey premises; identify hazards and protection needs
  • 5130 Backflow Prevention Assembly Repairer Diagnose and repair testable assemblies
  • 5140 Fire Protection CCC Tester Test assemblies serving fire-protection systems
  • 5150 Backflow Prevention Program Administrator Administer utility or agency CCC programs

For the ASSE 5110 exam, 5110 is the focus . Know the sibling numbers at recognition level so distractors such as “ASSE 5130 authorizes annual field testing of RPs for any tester” fail immediately. Holding 5110 does not automatically authorize repair, survey, or program administration. Each credential has its own training, examination, and scope boundaries (covered again in the reporting and career-path chapter).

What ASSE 5110 actually defines

ASSE 5110 is the personnel qualifications standard (and the certification program built on it) for testers who perform periodic field tests on installed testable assemblies. Competencies typically include:

Theory — hydraulics of backpressure and backsiphonage; how differentials drive check, relief, and air-inlet action.

Assembly identification — distinguish RP, DC, PVB, SVB (and recognize detector and non-testable devices at survey level).

Equipment — use a calibrated differential-pressure gauge with correct hose discipline, bleeding, and air elimination.

Procedures — apply an ASSE-recognized field-test procedure (for example USC 10th Edition) consistently on all four practical assemblies.

Criteria — apply published pass/fail values; do not invent “house” numbers.

Reporting — record results in language purveyors and AHJs can use; know when a failed assembly must be reported and taken out of reliance until repaired and retested by a qualified person.

The written exam samples the knowledge stack. The practical exam samples whether you can execute procedures under time pressure without notes. Series 5000 is the design document behind both gates.

Third-party certification, schools, instructors, and proctors

A defining feature of ASSE 5110 is nationally recognized third-party certification . The training provider teaches you; a separate certification pathway (with ASSE program rules) awards the credential after you pass written and practical requirements. That separation matters for employers, purveyors, and courts: your certificate is not merely a “school diploma” from the same entity that sold the course.

Program integrity depends on approved infrastructure:

Role What they control Why the exam cares

ASSE-approved school Delivers the required course hours and lab access Curriculum maps to Series 5000 competencies

Approved instructor Teaches theory and supervised hands-on practice Must meet program qualifications

Proctor / practical examiner Administers written and practical exams Independent evaluation of candidate performance

Certification body (ASSE program) Issues, tracks, and renews credentials Third-party status and national recognition

If a jurisdiction “accepts ASSE 5110,” it is accepting this stack—not a one-off local workshop without the Series 5000 backbone. When you recertify, you remain inside the same program rules (recert exam format and retake limits are logistics; the standard still defines the competence model).

Why ANSI consensus matters for legal defensibility

Standards can be proprietary, industry-association only, or ANSI-accredited consensus standards. Series 5000 sits in the consensus camp. That matters when:

A state or local code references ASSE Series 5000 or accepts ASSE 5110 by name.

A purveyor ordinance requires “ASSE-certified tester or equivalent.”

A dispute arises after contamination, failed inspection, or alleged improper testing—attorneys and expert witnesses look for procedures and credentials that are published, consensus-based, and widely adopted .

Consensus does not make a tester immune from error. It does make the framework easier to defend: training content, exam blueprints, and recognized procedures are not secret house rules. On the written exam, expect items that contrast product performance standards with professional qualifications standards , or that ask why third-party certification is preferred over self-attestation.

How Series 5000 fits the regulatory stack

Series 5000 does not replace local law. It is a qualification standard that authorities adopt, accept, or recognize . Day-to-day tester obligations still come from:

Federal drinking-water framework (SDWA and EPA guidance — Section 11.4).

State health or environmental rules implementing cross-connection control.

Local purveyor / AHJ ordinances, approved assembly lists, test frequencies, and report forms.

Manufacturer listing and installation instructions for the specific assembly.

Recognized field-test manuals (USC 10th and peers — Section 11.3) for step-by-step procedure and criteria.

Your 5110 card proves competence against Series 5000. Your work product must still satisfy the purveyor who owns the program. If local rules are stricter than the minimum you learned in school, local rules win for fieldwork. If a question asks what defines national tester competencies, the answer points to Series 5000 / ASSE 5110 , not a city ordinance number you invent.

Exam traps for this section

  • Trap Correct correction
  • “ASSE 1013 is the tester certification” 1013 is the RP product standard; 5110 is the tester
  • “5110 includes automatic repair authority” Repair is 5130 (separate credential and scope)

“Any plumbing school can issue ASSE 5110” Certification requires the ASSE program path with approved schools/proctors

  • “Series 5000 is a plumbing code” It is a professional qualifications standard, not a model plumbing code book
  • “ANSI means optional industry tip sheet” ANSI consensus strengthens adoption and defensibility
  • Field habit that matches the standard

When you introduce yourself on a job site or fill a purveyor form, identify yourself as an ASSE 5110 (or locally accepted equivalent) tester, list your certification number and expiration, and use a procedure your school and the AHJ recognize. That habit is Series 5000 in action: competent person, recognized method, accountable report. The rest of this chapter drills the device numbers , the USC 10th procedure family, and the AWWA/EPA/SDWA program layer so you can place every document in the correct shelf of the regulatory library.