Study guide
9.2 SVB Field Test Procedure
ASSE 5110 Backflow Prevention Assembly Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About ASSE 5110 and the Series 5000 Program 1.2 Eligibility, 40-Hour Course, Written & Practical Format 1.3 Validity, Recertification, and Retake Rules
2 Hydraulics Fundamentals
2.1 Pressure, Head, and Atmospheric Reference 2.2 Static vs Flowing Conditions for Testers 2.3 PSID and How Differentials Are Measured
3 Backpressure, Backsiphonage & Differentials
3.1 Backpressure: Causes and Field Examples 3.2 Backsiphonage: Causes and Field Examples 3.3 How Differentials Drive Relief and Air-Inlet Action 3.4 When and Why Backflow Occurs in Distribution Systems
4 Cross-Connection Recognition
4.1 Health Hazard vs Non-Health Hazard Classification 4.2 Common Cross-Connections and Correct Protection 4.3 Containment vs Isolation Strategies
5 RP and DC Assemblies
5.1 RP (ASSE 1013) Components and Operation 5.2 RP Relief Valve Theory and Zone Protection 5.3 DC (ASSE 1015) Components and Operation 5.4 When to Use RP vs DC
6 PVB, SVB & Detector Assemblies
6.1 PVB (ASSE 1020) Components and Operation 6.2 SVB (ASSE 1056) Components and Operation 6.3 RPDA and DCDA Detector Assemblies (1047/1048) 6.4 Non-Testable Devices Testers Must Recognize
7 Test Equipment & Calibration
7.1 Three-Valve Differential Pressure Gauges 7.2 Five-Valve Gauges and Hose Discipline 7.3 Bleeding, Hookup Sequence, and Air Elimination 7.4 Calibration, Accuracy, and Field Verification
8 RP & DC Field Test Procedures
8.1 RP Field Test Procedure (USC 10th Edition) 8.2 RP Pass/Fail Criteria and Troubleshooting 8.3 DC Field Test Procedure 8.4 DC Failures and Common Causes
9 PVB/SVB Tests & Practical Sequence
9.1 PVB Field Test Procedure 9.2 SVB Field Test Procedure 9.3 Comparing the Four Practical-Exam Assemblies 9.4 Hands-On Sequence Under Practical Exam Pressure
10 Installation Requirements & Inspection
10.1 Orientation, Clearance, and Elevation Rules 10.2 RP Drainage, Air Gap, and Flood Protection 10.3 Freeze Protection and Thermal Expansion 10.4 Pre-Test Visual Inspection
11 Codes, Standards & Manuals
11.1 ASSE Series 5000 and 5110 Professional Qualifications 11.2 Device Standards 1013, 1015, 1020, 1056 11.3 USC Manual of Cross-Connection Control 10th Edition 11.4 AWWA M14, EPA 816-R-03-002, and SDWA Framework
12 Reporting, Boundaries & Exam Prep
12.1 Field Test Reports and Pass/Fail Language 12.2 Purveyor Notification and Record Retention 12.3 Tester vs Repairer vs Surveyor Boundaries 12.4 Written Exam Strategy, Study Plan, and Next Credentials
9.2 SVB Field Test Procedure
Key Takeaways Explain This Topic AI
SVB (ASSE 1056) field criteria match the PVB family: check ≥ 1.0 psid and air inlet opens ≥ 1.0 psid above atmospheric (USC 10th).
Spill-resistant design reduces start-up spillage; it does not remove the need for air-inlet or check testing.
SVBs remain backsiphonage-only devices under continuous pressure—they are not backpressure protection and are not non-testable AVBs.
USC 10th reversed the SVB order: check valve is Test No. 1 and air inlet is Test No. 2 (the PVB order is unchanged).
Elevation and free atmosphere at the air-inlet path still control whether the assembly can actually break vacuum.
Last updated: August 2026
9.2 SVB Field Test Procedure
Quick Answer: An ASSE 1056 spill-resistant vacuum breaker (SVB) is field-tested in the same criteria family as a PVB: check ≥ 1.0 psid and air inlet opens ≥ 1.0 psid above atmospheric . Spill-resistant design changes how the assembly behaves during fill, pressurization, and bleed —not the public-health pass numbers. Elevation discipline and free atmosphere at the air-inlet path still apply.
Same family, different manners
Think of the SVB as a backsiphonage / continuous-pressure vacuum breaker engineered so the air-inlet region does not spit and puddle the way a conventional PVB often does at start-up. That matters for indoor mechanical rooms, finished ceilings, freeze enclosures, and any location where PVB spillage is unacceptable.
What does not change for the ASSE 5110 tester:
- Item PVB (1020) SVB (1056)
- Hazard role Backsiphonage; continuous pressure OK Same family
- Backpressure protection No No
- Check pass (USC typical) ≥ 1.0 psid ≥ 1.0 psid
- Air inlet pass (USC typical) ≥ 1.0 psid above atmospheric ≥ 1.0 psid above atmospheric
- Shutoffs + test cocks Required for testability Required for testability
- Elevation Critical level high enough (commonly ≥ 12 in above highest outlet) Same class of rule
What does change is product geometry and how water is managed around the air-inlet path during normal pressurization. That is why bleed and start-up “feel” different even when your pass criteria flashcards look identical.
Why SVB may behave differently during bleed and start
On a classic PVB, rapid pressurization or certain shutoff manipulations can push water out the air-inlet area until the poppet seats under pressure. Training stands get wet; indoor floors get wet; freeze boxes get wet. The SVB uses spill-resistant construction so that water is retained or directed such that normal start-up spillage is minimized .
During a field test you may notice:
Less free discharge from the vent area when you first pressurize or when you crack a test cock.
A different visual cue for “air inlet opened”—you still need the gauge reading , not a puddle, as your pass evidence.
Slightly different manufacturer bleed sequences in the instruction sheet even though USC pass thresholds match the PVB family.
Exam trap: “SVB does not need an air-inlet test because it is spill-resistant.” False. Spill resistance is a nuisance-water design feature. Protection still requires a working air inlet that opens at the required differential and a check that holds.
Test cocks, shutoffs, and isolation logic
SVB assemblies remain testable assemblies : inlet and outlet resilient-seated shutoffs , plus test cocks for gauge connection. Procedural outline parallels PVB:
Identify as ASSE 1056 (not 1020, not 1001 AVB, not 1015 DC).
Visual: shutoffs, test cock(s), air-inlet path free of plugs/tape, canopy/cover not sealed against atmosphere, elevation OK.
Notify users if isolation interrupts service.
Close both shutoffs to isolate pressure inside the assembly (an SVB typically has only one test cock , so isolation—not cock selection—creates the test condition).
Install the bleed-off valve arrangement on the test cock as the 10th-Edition procedure directs, attach the high-side hose, and bleed solid water .
Raise the gauge so its centerline sits at the vent-valve (vent-screw) outlet , and keep it there for both readings.
Test No. 1 — check valve: reduce the downstream side to atmosphere; when flow from the vent valve ceases and the needle stabilizes, the check must hold ≥ 1.0 psid .
Test No. 2 — air inlet: with the gauge still elevated, drain water from the assembly through the gauge; the air inlet must initially open at ≥ 1.0 psid and then, with the kit lowered and the hose removed, continue to open fully .
Restore shutoffs and the test cock; remove hoses; complete the report.
Order matters: the 9th → 10th Edition change
This is a classic written-exam discriminator. In the USC 9th Edition , the SVB air inlet reading (Test No. 1) came before the check valve reading (Test No. 2). The 10th Edition reversed it : check valve first (Test No. 1), air inlet second (Test No. 2) , to simplify the procedure. The PVB order did not change—on a PVB the air inlet is still Test No. 1 and the check is Test No. 2.
- Assembly USC 9th order USC 10th order
- PVB (1020) Air inlet → check Air inlet → check (unchanged)
- SVB (1056) Air inlet → check Check → air inlet (reversed)
If your school’s recognized procedure inserts a manufacturer-specific bleed order for a particular SVB model, follow that order on practical day—proctors grade the procedure you were taught against Series 5000 / USC competencies, not improvisation.
Hose discipline notes that matter more when spillage is low
Because an SVB may not “announce” problems with a spray of water, candidates sometimes rush the bleed. Air left in the gauge still ruins differentials whether or not the floor is dry. Take the extra ten seconds to rock hoses, open bleed ports, and watch for a solid column before you mark numbers.
Also confirm you have not capped or taped an air-inlet path “to keep the room dry.” That installation defect turns a spill-resistant vacuum breaker into a non-protecting device. Report it.
Interpreting SVB readings next to PVB readings
Use one mental scoreboard for both:
- Reading Pass? Notes
- Check 1.2 psid, air inlet 1.4 psi Pass (both ≥ 1.0) Record both numbers
- Check 1.0 psid, air inlet 1.0 psi Pass (minimums met) Minimum is not “extra credit”—it is the floor
- Check 1.5 psid, air inlet 0.7 psi Fail Air inlet low—same fail as PVB
- Check 0.6 psid, air inlet 1.8 psi Fail Check fouled/weak
- Air inlet never opens Fail Sticky path or blocked atmosphere
Do not “grade on a curve” because the device is spill-resistant. Do not invent a relief-valve step— SVBs have no RP-style differential relief valve .
Practical differences you might see on the stand
- Observation PVB tendency SVB tendency Tester response
- Floor under air inlet after pressurization Often wet Usually drier Still trust the gauge, not the floor
Indoor suitability Often discouraged where spillage matters Preferred where spill resistance is needed Installation choice is not your “pass” decision, but note location
Air-inlet motion visibility Sometimes obvious spit/open May be subtler Watch canopy/poppet and differential
Confusion risk Called “vacuum breaker” generically Called “spill-resistant” Always match the device standard number on the plate
Mini case: indoor SVB vs outdoor PVB
Outdoor irrigation PVB: You expect possible spit when pressurizing. You still record air inlet 1.1 psi and check 1.3 psid → pass.
Indoor mechanical-room SVB: Almost no water on the pad when you pressurize. A classmate assumes “it must be fine” without reading the gauge. You continue the procedure: air inlet opens at 0.9 psi → fail . Spill resistance did not create a free pass; the spring/poppet still failed the 1.0 minimum.
Common SVB-specific mistakes
Treating SVB like a non-testable AVB because it “just vents.” AVBs (1001) are a different class; SVBs are testable 1056 assemblies.
Skipping elevation because the unit is indoors on a wall. Indoor walls can still be below a high fixture or process outlet.
Forcing the air inlet open to see motion without recording the differential—motion without a number is not a USC-style pass.
Applying DC two-check logic because you see “two shutoffs and test cocks.” An SVB is still a vacuum-breaker family device, not a double check.
Stopping the fail-mode test early on practical day when the first reading is low—complete the demonstration the proctor requires.
Bridge
You can now test PVB and SVB as a criteria twin pair with product-specific manners. Section 9.3 freezes all four practical assemblies— RP, DC, PVB, SVB —into one comparison table so you never grab the wrong numbers under the 90-minute clock.