Study guide
12.4 Written Exam Strategy, Study Plan, and Next Credentials
ASSE 5110 Backflow Prevention Assembly Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About ASSE 5110 and the Series 5000 Program 1.2 Eligibility, 40-Hour Course, Written & Practical Format 1.3 Validity, Recertification, and Retake Rules
2 Hydraulics Fundamentals
2.1 Pressure, Head, and Atmospheric Reference 2.2 Static vs Flowing Conditions for Testers 2.3 PSID and How Differentials Are Measured
3 Backpressure, Backsiphonage & Differentials
3.1 Backpressure: Causes and Field Examples 3.2 Backsiphonage: Causes and Field Examples 3.3 How Differentials Drive Relief and Air-Inlet Action 3.4 When and Why Backflow Occurs in Distribution Systems
4 Cross-Connection Recognition
4.1 Health Hazard vs Non-Health Hazard Classification 4.2 Common Cross-Connections and Correct Protection 4.3 Containment vs Isolation Strategies
5 RP and DC Assemblies
5.1 RP (ASSE 1013) Components and Operation 5.2 RP Relief Valve Theory and Zone Protection 5.3 DC (ASSE 1015) Components and Operation 5.4 When to Use RP vs DC
6 PVB, SVB & Detector Assemblies
6.1 PVB (ASSE 1020) Components and Operation 6.2 SVB (ASSE 1056) Components and Operation 6.3 RPDA and DCDA Detector Assemblies (1047/1048) 6.4 Non-Testable Devices Testers Must Recognize
7 Test Equipment & Calibration
7.1 Three-Valve Differential Pressure Gauges 7.2 Five-Valve Gauges and Hose Discipline 7.3 Bleeding, Hookup Sequence, and Air Elimination 7.4 Calibration, Accuracy, and Field Verification
8 RP & DC Field Test Procedures
8.1 RP Field Test Procedure (USC 10th Edition) 8.2 RP Pass/Fail Criteria and Troubleshooting 8.3 DC Field Test Procedure 8.4 DC Failures and Common Causes
9 PVB/SVB Tests & Practical Sequence
9.1 PVB Field Test Procedure 9.2 SVB Field Test Procedure 9.3 Comparing the Four Practical-Exam Assemblies 9.4 Hands-On Sequence Under Practical Exam Pressure
10 Installation Requirements & Inspection
10.1 Orientation, Clearance, and Elevation Rules 10.2 RP Drainage, Air Gap, and Flood Protection 10.3 Freeze Protection and Thermal Expansion 10.4 Pre-Test Visual Inspection
11 Codes, Standards & Manuals
11.1 ASSE Series 5000 and 5110 Professional Qualifications 11.2 Device Standards 1013, 1015, 1020, 1056 11.3 USC Manual of Cross-Connection Control 10th Edition 11.4 AWWA M14, EPA 816-R-03-002, and SDWA Framework
12 Reporting, Boundaries & Exam Prep
12.1 Field Test Reports and Pass/Fail Language 12.2 Purveyor Notification and Record Retention 12.3 Tester vs Repairer vs Surveyor Boundaries 12.4 Written Exam Strategy, Study Plan, and Next Credentials
12.4 Written Exam Strategy, Study Plan, and Next Credentials
Key Takeaways Explain This Topic AI
ASSE 5110 written testing is commonly 100 questions, about 2 hours, 70% pass, closed-book—confirm exact provider logistics
High-yield drill targets: device standard numbers, USC psid criteria, RP vs DC vs PVB/SVB, backpressure vs backsiphonage, gauge discipline, install rules, and the 3-year recert cycle
Study path works best as theory → assemblies → equipment → procedures → install/codes → timed mock practical and written practice
Free practice questions are available at ExamFinch /practice/asse-5110 to reinforce weak categories
After 5110, common next credentials are 5130 repairer or 5120 surveyor; schedule recertification early within the 3-year cycle
Last updated: October 2026
12.4 Written Exam Strategy, Study Plan, and Next Credentials
Quick Answer: Plan for a closed-book written exam commonly structured as 100 questions , about 2 hours , 70% to pass (confirm your provider’s exact rules), plus a hands-on practical . Drill device numbers , USC psid criteria , RP vs DC vs PVB/SVB , backpressure vs backsiphonage , gauge discipline , install rules , and recert timing . Study in order: theory → assemblies → equipment → procedures → install/codes → mock timing . Use free practice at ExamFinch ASSE 5110 practice . After 5110, 5130 or 5120 are common next steps. Recert every 3 years —schedule early.
Know the written exam shape
ASSE 5110 assessment is two-part in spirit: a written knowledge exam and a practical demonstration on the four core assemblies (RP/ASSE 1013, DC/ASSE 1015, PVB/ASSE 1020, SVB/ASSE 1056). Provider logistics can vary slightly, but the national pattern you should memorize for planning is:
- Element Typical target to memorize
- Written length 100 questions
- Written time About 2 hours (some providers list a similar multi-hour window—know yours)
- Written pass 70%
- Materials Closed-book (no notes, no phone procedures)
- Practical Field test all four assemblies under time pressure; report completion; often ≥1 fail mode
- Credential life 3 years , then recert
- Recert written (pattern) Shorter exam (commonly 50 questions / 1.5 hours) + practical—confirm current rules
Treat “typical” as your study baseline and verify the candidate handbook from your course provider the week before test day. Do not walk in assuming open notes.
High-yield drill list (written + practical theory)
If time is short, drill these until recall is automatic:
1) Device standard numbers
- Number Assembly
- ASSE 1013 Reduced pressure principle (RP)
- ASSE 1015 Double check (DC)
- ASSE 1020 Pressure vacuum breaker (PVB)
- ASSE 1056 Spill-resistant vacuum breaker (SVB)
- ASSE 1047 / 1048 RPDA / DCDA detector assemblies (recognition)
- 2) USC-style psid/psi field criteria (10th Edition pattern taught in this guide)
- Assembly / element Minimum / rule
- RP relief Opens at ≥ 2.0 psid
- RP check #1 ≥ 5.0 psid and above relief opening point
- RP check #2 Tight against backpressure — no psid
- DC each check ≥ 1.0 psid tight
- PVB/SVB air inlet Opens at ≥ 1.0 psid above atmospheric
- PVB/SVB check ≥ 1.0 psid
- 3) RP vs DC vs PVB/SVB (selection logic)
RP: continuous mechanical protection with intermediate zone + relief; used for health-hazard applications where approved.
DC: two checks, no relief zone dumping; non-health applications where approved—not a substitute for RP on health hazards.
PVB/SVB: backsiphonage-focused protection with air inlet; orientation/elevation rules matter; not a universal substitute for RP under backpressure health-hazard conditions.
4) Backpressure vs backsiphonage
Backpressure: downstream pressure higher than supply (pumps, thermal expansion, elevation head).
Backsiphonage: supply pressure drops below downstream/atmospheric reference (main break, high demand), allowing atmosphere-driven reverse flow.
5) Gauge discipline
Know 3-valve vs 5-valve roles at a high level.
Bleed solid water ; air falsifies differentials.
Calibration currency (commonly annual) belongs on the report with gauge ID.
6) Install rules (tester inspection mindset)
Flow direction, clearances, RP relief drainage / air gap needs, freeze exposure, PVB/SVB critical-level elevation patterns, accessibility of shutoffs and test cocks.
7) Recert cycle
3-year validity; recert early so you never fall off the certified list during peak testing season.
High-yield summary table (pin this)
- Topic Memory hook
- Written exam ~ 100 Q , ~ 2 hr , 70% , closed-book
- Practical 1013 / 1015 / 1020 / 1056 continuous performance + report
- RP numbers Relief ≥2.0 ; #1 ≥5.0 & > relief; #2 ≥1.0
- DC numbers Each check ≥1.0
- PVB/SVB numbers Check ≥1.0 ; air inlet ≥1.0 psid above atmospheric
- Health hazard default Think RP (where approved)—not DC
- Backpressure Downstream higher than supply
- Backsiphonage Supply collapse / sub-atmospheric tendency
- Report integrity Measured values; never alter to force pass
- 5110 vs 5130 vs 5120 Test / Repair / Survey
- Credential life 3 years —calendar recert early
- Practice site /practice/asse-5110
- Study path that builds (not crams)
Use a staged path so later procedures sit on firm theory:
Theory — pressure, head, atmosphere, psid, backpressure vs backsiphonage, when reverse flow happens.
Assemblies — RP/DC internals and zone theory; PVB/SVB air-inlet logic; detector recognition; non-testable device recognition.
Equipment — gauge valves, hose discipline, bleeding, calibration.
Procedures — USC-style RP, DC, PVB, SVB sequences; pass/fail troubleshooting; practical order under time.
Install / codes — orientation, clearances, drainage, freeze/expansion, Series 5000/device standards, USC manual role, AWWA M14/EPA/SDWA framework awareness.
Admin finish — reports, purveyor deadlines, role boundaries (this chapter).
Mock timing — full practical dry runs with reports; timed written sets.
Daily drill suggestion in the last two weeks: 20–30 mixed written questions + one assembly procedure spoken out loud while you mime hose moves. Speaking the procedure exposes gaps that silent reading hides.
Written strategy on test day
First pass: answer every item you know in under ~45–60 seconds; flag long scenario items.
Second pass: attack flags; draw tiny RP zone sketches in the margin if allowed scrap paper.
Watch units: psid vs psi, and “above relief” vs raw 5.0 on check #1.
Eliminate extremes: answers that defeat relief/air inlets or treat DC as health-hazard protection are usually wrong.
Do not change answers without a specific reason.
Time check: at halfway, you should be near question 50 if the exam is 100 items.
Free practice on ExamFinch
Reinforce weak categories with free practice questions at /practice/asse-5110 . Use practice to diagnose—not to memorize single items:
Missed hydraulics → re-read Chapters 2–3.
Missed assembly operation → Chapters 5–6.
Missed procedures/equipment → Chapters 7–9.
Missed install/codes → Chapters 10–11.
Missed reporting/roles → this chapter.
Track misses in a notebook of facts , not question stems (so you learn the underlying rule).
Practical timing mindset (brief)
Written knowledge fails if practical hands freeze. In the final week:
Practice a consistent order for the four assemblies.
Practice report writing in under a few minutes per assembly.
Practice one deliberate fail-mode response: read it, write it, call it Fail.
Pack a personal checklist: IDs, calibration card, forms, PPE, light, towels.
Next credentials after 5110
Once you are comfortable testing:
ASSE 5130 Repairer — natural next step if customers ask you to fix what you fail; increases revenue and closes the compliance loop.
ASSE 5120 Surveyor — natural if you like premises evaluation, hazard classification, and consulting-style recommendations.
ASSE 5150 Administrator — if you move into utility/campus program leadership.
Pick based on your market. Industrial areas with many fails reward 5130 . Consulting and facility management paths reward 5120 . You can hold multiple credentials over a career; earn 5110 cleanly first .
Recertification: schedule early
Three years feels long until spring testing season collides with an expired card. Put the expiration date on a calendar with reminders at 12 months , 6 months , and 3 months . Recertifying in the window that preserves your cycle (as taught in Chapter 1) beats repeating a full initial 40-hour path because you waited too long. Keep gauge calibration and CE/course requirements aligned so admin details do not block an otherwise ready technician.
Closing the guide
If you can explain why reverse flow happens, how each assembly stops it, how to prove performance with a gauge, how to install/inspect for testability, how to report honestly, and where your credential ends, you are ready for ASSE 5110. Use the high-yield table above as a last-night review, sleep, and test with the same integrity you will bring to every vault: measured truth, complete forms, public health first.