Study guide

1.3 Medical Gases, Hazards & Permitted Uses

ASSE 6010 Medical Gas Systems Installer Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The Credential, Codes & Medical Gas Fundamentals

1.1 The ASSE 6010 Credential: Eligibility, Exam Format & Recertification 1.2 Codes, Referenced Standards & the Medical Gas Team 1.3 Medical Gases, Hazards & Permitted Uses 1.4 Risk Categories & Category 1, 2, and 3 Piped Systems 1.5 Key NFPA 99 Definitions & Terminology

2 Chapter 2: Piping Materials, Oxygen Cleanliness & Joining Methods

2.1 Tube Specifications for Medical Gas and Vacuum Piping 2.2 Oxygen-Clean Materials: Delivery, Handling & Recleaning 2.3 Joining Methods: Permitted and Prohibited Joints

3 Chapter 3: Brazing Medical Gas Piping

3.1 Joint Preparation, Fittings, Filler Metals & Flux 3.2 Nitrogen Purge: Setup, Control & Final Tie-In Exception 3.3 Heating, Filling & Inspecting Brazed Joints 3.4 Brazing Procedure & Brazer Qualification, Records and Continuity

4 Chapter 4: Installing the Distribution Piping

4.1 Pipe Sizing, Protection & Permitted Locations 4.2 Supports, Buried Piping, Flexible Connectors & System Interconnections

5 Chapter 5: Valves, Station Outlets, Alarms & Labeling

5.1 Valve Requirements: Source, Main Line, Riser, Service & In-Line Valves 5.2 Zone Valves & Zone Valve Box Assemblies 5.3 Station Outlets & Inlets, Manufactured Assemblies & Pressure Indicators 5.4 Warning Systems: Master, Area & Local Alarms 5.5 Labeling, Identification & Color Codes

6 Chapter 6: Central Supply Systems & Source Equipment

6.1 Central Supply Locations, Cylinder Manifolds, Line Controls & Relief Valves 6.2 Cryogenic Supplies, Reserves, EOSC, IBER & Oxygen Concentrators 6.3 Medical Air Compressor Systems 6.4 Medical-Surgical Vacuum, WAGD & Medical Support Gas Sources

7 Chapter 7: Testing, Verification & Documentation

7.1 Installer Tests I: Blowdown, Initial Pressure, Cross-Connection & Piping Purge 7.2 Installer Tests II: 24-Hour Standing Pressure & Vacuum Tests, Inspection & Witnessing 7.3 System Verification: The Verifier's Test Sequence 7.4 Tie-Ins, Breached Systems, Operational Flow & Gas Concentration Tests 7.5 Documentation, Records & System Turnover

1.3 Medical Gases, Hazards & Permitted Uses

Key Takeaways Explain This Topic AI

Patient medical gases include oxygen, nitrous oxide, medical air, carbon dioxide, helium, and their mixtures. They are delivered at a standard 50-55 psi.

Medical support gases are nitrogen NF and instrument air. They power equipment, are not breathed, and are normally piped at 160-185 psi.

NFPA 99 treats gas mixtures with more than 23.5% oxygen as oxygen-enriched, so components must be compatible with oxygen service.

Medical air must meet the USP medical air monograph, contain no detectable liquid hydrocarbons, and contain less than 25 ppm gaseous hydrocarbons.

Medical air sources may feed only the medical air distribution system, and only for breathing and for calibrating respiratory devices.

Last updated: October 2026

The Gases an Installer Pipes

NFPA 99 defines medical gas and medical support gas broadly. The provisions apply to piped systems for oxygen, nitrous oxide, medical air, carbon dioxide, helium, nitrogen, instrument air, and their mixtures. Where a rule names one gas, it applies only to that gas.

  • Service Category Standard gauge pressure Typical use
  • Oxygen (O2) Patient medical gas 50-55 psi Breathing therapy, anesthesia, ventilators
  • Medical air Patient medical gas 50-55 psi Breathing, ventilators, calibrating respiratory devices
  • Nitrous oxide (N2O) Patient medical gas 50-55 psi Anesthesia and analgesia
  • Carbon dioxide (CO2) Patient medical gas 50-55 psi Insufflation during laparoscopic surgery
  • Helium (He) Patient medical gas 50-55 psi Special respiratory mixtures
  • Nitrogen (N2) Medical support gas 160-185 psi Powering surgical tools, booms, and pendants
  • Instrument air Medical support gas 160-185 psi Powering surgical tools and pneumatic devices
  • Medical-surgical vacuum Vacuum 15-30 in. HgV Drainage, aspiration, and suction of body fluids
  • WAGD Vacuum Varies with system type Capturing gases vented from the anesthesia breathing circuit

Medical support gases are used mainly to power equipment in patient care procedures. They may be piped to areas with a support purpose and, where appropriate, to laboratories. A support gas system may not carry oxidizing gases other than air, and it may not carry gases meant for patient or staff breathing.

Why Oxidizers Change the Rules

Oxygen and nitrous oxide do not burn, but they make other materials burn far more readily and intensely. NFPA 99 requires designers and installers to consider the fire and explosion hazards of positive-pressure gas systems and vacuum systems in design, installation, testing, operation, and maintenance. For central supply materials, the code requires the following:

Oxygen-compatible construction wherever oxygen, nitrous oxide, their mixtures, or any mixture containing more than 23.5% oxygen will be handled, at the temperatures and pressures involved.

No polymeric material in interconnecting hose that carries oxygen at gauge pressures above 435 psi (3000 kPa) . Cylinder pressures are far higher than pipeline pressure.

Low-temperature materials wherever components can see cryogenic temperatures.

Installers see the same hazard in daily work:

Oil, grease, and cutting lubricants inside a pipe are fuel. A sudden pressure rise (adiabatic compression) or a fast-moving particle can ignite them in an oxygen stream.

Oxide scale and chips left from brazing or cutting become particulates that travel to patient equipment.

A cross-connection , where one gas is piped to another gas's outlet, can deliver the wrong gas to a patient. That is why NFPA 99 requires gas-specific outlets, labeling, cross-connection tests, and gas concentration tests.

Quality Standards for the Gases

  • Gas Concentration the verifier must confirm
  • Oxygen USP At least 99% oxygen
  • Oxygen 93 USP (from concentrators) 90% to 96% oxygen
  • Nitrous oxide USP At least 99% nitrous oxide
  • Nitrogen NF No more than 1% oxygen, or at least 99% nitrogen
  • Medical air USP 19.5% to 23.5% oxygen
  • Other gases Named gases within plus or minus 1%, or per specification

Medical air gets extra attention. It may come from cylinders, bulk containers, or medical air compressors, or it may be reconstituted from oxygen USP and oil-free, dry nitrogen NF. It must meet the medical air USP requirements, contain no detectable liquid hydrocarbons , and contain less than 25 ppm gaseous hydrocarbons . It may hold no more than 1 mg/m3 of permanent particulates sized 1 micron or larger.

Permitted Uses: Piping Patient Gases Only Where They Belong

Central supply systems for oxygen, medical air, nitrous oxide, carbon dioxide, and the other patient gases may be piped only to medical gas outlets. Those outlets must be in areas where licensed medical professionals direct the use of the gases for purposes consistent with:

Direct respiration by patients

Clinical application to a patient, such as carbon dioxide insufflation or purging heart-lung machine blood pathways

  • Medical device applications directly related to respiration
  • Power for medical devices used directly on patients
  • Calibration of the devices in items 1-4
  • Simulation centers for educating, training, and assessing health care professionals

Several related limits come up on exams:

Medical air sources connect only to the medical air distribution system. They serve only human respiration and the calibration of respiratory devices. Medical air can never feed a shop air line.

Support gas central supplies may not be piped to, or used for, anything except medical support applications.

Medical-surgical vacuum and WAGD may not be used for nonmedical applications, such as steam condensate return.

Warning

If someone asks to run a branch off the medical air main for a lab bench, a pneumatic door, or a tool outlet in a workshop, the answer is no. That use falls outside the permitted purposes, and it would expose the patient air supply to contamination and backflow.