Study guide

6.4 Medical-Surgical Vacuum, WAGD & Medical Support Gas Sources

ASSE 6010 Medical Gas Systems Installer Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The Credential, Codes & Medical Gas Fundamentals

1.1 The ASSE 6010 Credential: Eligibility, Exam Format & Recertification 1.2 Codes, Referenced Standards & the Medical Gas Team 1.3 Medical Gases, Hazards & Permitted Uses 1.4 Risk Categories & Category 1, 2, and 3 Piped Systems 1.5 Key NFPA 99 Definitions & Terminology

2 Chapter 2: Piping Materials, Oxygen Cleanliness & Joining Methods

2.1 Tube Specifications for Medical Gas and Vacuum Piping 2.2 Oxygen-Clean Materials: Delivery, Handling & Recleaning 2.3 Joining Methods: Permitted and Prohibited Joints

3 Chapter 3: Brazing Medical Gas Piping

3.1 Joint Preparation, Fittings, Filler Metals & Flux 3.2 Nitrogen Purge: Setup, Control & Final Tie-In Exception 3.3 Heating, Filling & Inspecting Brazed Joints 3.4 Brazing Procedure & Brazer Qualification, Records and Continuity

4 Chapter 4: Installing the Distribution Piping

4.1 Pipe Sizing, Protection & Permitted Locations 4.2 Supports, Buried Piping, Flexible Connectors & System Interconnections

5 Chapter 5: Valves, Station Outlets, Alarms & Labeling

5.1 Valve Requirements: Source, Main Line, Riser, Service & In-Line Valves 5.2 Zone Valves & Zone Valve Box Assemblies 5.3 Station Outlets & Inlets, Manufactured Assemblies & Pressure Indicators 5.4 Warning Systems: Master, Area & Local Alarms 5.5 Labeling, Identification & Color Codes

6 Chapter 6: Central Supply Systems & Source Equipment

6.1 Central Supply Locations, Cylinder Manifolds, Line Controls & Relief Valves 6.2 Cryogenic Supplies, Reserves, EOSC, IBER & Oxygen Concentrators 6.3 Medical Air Compressor Systems 6.4 Medical-Surgical Vacuum, WAGD & Medical Support Gas Sources

7 Chapter 7: Testing, Verification & Documentation

7.1 Installer Tests I: Blowdown, Initial Pressure, Cross-Connection & Piping Purge 7.2 Installer Tests II: 24-Hour Standing Pressure & Vacuum Tests, Inspection & Witnessing 7.3 System Verification: The Verifier's Test Sequence 7.4 Tie-Ins, Breached Systems, Operational Flow & Gas Concentration Tests 7.5 Documentation, Records & System Turnover

6.4 Medical-Surgical Vacuum, WAGD & Medical Support Gas Sources

Key Takeaways Explain This Topic AI

Category 1 vacuum sources need two or more pumps that serve peak calculated demand with the largest pump out of service, plus a receiver and backflow prevention.

Vacuum systems other than liquid ring must have at least duplex inlet filtration on the patient side, at least 99.97% efficient at 0.3 micron (HEPA), sized for 100% of peak demand with one filter isolated.

Vacuum exhausts must be outdoors, at least 25 ft from doors, windows, air intakes, and other openings, at a different level from air intakes, and free of dips and loops or provided with a drip leg.

Pumps dedicated to WAGD must use materials, lubricants, and sealants that are inert to oxygen, nitrous oxide, and halogenated anesthetics.

Instrument air dew point alarms activate above -22°F (-30°C), and an instrument air standby header holds enough cylinders for 1 hour of normal operation.

Last updated: October 2026

Medical-Surgical Vacuum: Uses and Limits

Medical-surgical vacuum provides drainage, aspiration, and suction to remove body fluids from patients. The facility may not use the medical-surgical vacuum or WAGD system for nonmedical applications , such as steam condensate return.

Vacuum Central Supply Requirements (Category 1)

  • Component Requirement
  • Pumps Two or more , enough to serve peak calculated demand with the largest pump out of service
  • Backflow Automatic means to prevent backflow from on-cycle pumps through off-cycle pumps
  • Isolation A shutoff valve or other means to isolate each pump without losing vacuum in the system

Receiver ASME Section VIII ; able to withstand 60 psi gauge and 30 in. HgV ; manual drain ; sized for the pump technology; serviceable without shutting down the system

Pump mounting Materials the manufacturer deems suitable; antivibration mountings ; flexible connectors to intake and outlet piping; liquid ring seal water of the quality the manufacturer recommends

Piping at the source Per the vacuum piping rules. Brass, galvanized, or black steel may be used between the pumps, discharges, receiver, and source valve as the manufacturer recommends.

  • Arrangement Service and continuous vacuum through a single fault
  • Source valve Required, per the valve rules

Lab connection Where one set of pumps also serves an analysis, research, or teaching lab, the lab connects separately at the receiver through its own isolation valve and fluid trap. A scrubber may be installed between them.

  • Inlet filtration (vacuum sources other than liquid ring)
  • At least duplex , so one filter can be changed without affecting the vacuum system
  • On the patient side of the vacuum producer
  • At least 99.97% efficient at 0.3 micron (HEPA)
  • Sized for 100% of peak calculated demand with one filter or filter bundle isolated
  • Isolation valves on both sides of each filter or bundle
  • A way to see any accumulated liquid
  • A vacuum relief petcock to relieve vacuum in the canister before the filter is changed
  • In normal operation, one filter or bundle is isolated as a standby
  • Vacuum Exhaust

The exhaust must keep noise and contaminated discharge away from people and air intakes:

  • Rule Requirement
  • Location Outdoors

Separation At least 25 ft (7.6 m) from any door, window, air intake, or other building opening, and from places of public assembly

Level At a different level from air intakes

Dispersion Placed so prevailing winds, nearby buildings, topography, and similar factors will not push exhaust into occupied areas or block dispersion

End treatment Turned down and screened with noncorroding screen

Drainage No dips or loops that could trap condensate or oil, or else a drip leg with a valved drain at the low point

Multiple pumps A common exhaust is allowed if sized for back pressure per the manufacturer and each pump can be isolated

Compare this with the medical air intake, which must be at least 25 ft from vacuum and WAGD discharges. Locating the vacuum exhaust and medical air intake properly is one of the most consequential layout decisions on a job.

WAGD

WAGD captures and removes gases vented from the patient breathing circuit during normal operation of anesthesia or analgesia equipment. WAGD producers are dedicated to that service.

Pumps dedicated to WAGD must meet the vacuum pump requirements, and they must be built with materials, lubricants, and sealants that are inert to oxygen, nitrous oxide, and halogenated anesthetics . Exhaust from anesthesia circuits can be oxygen-rich.

Low-vacuum producers such as fans or blowers designed for vacuum below 5 in. HgV may use materials the manufacturer deems suitable. They must have antivibration mountings and flexible connections, be used only for WAGD, and be connected by piping or ductwork suited to the service.

Where WAGD is produced by the medical-surgical vacuum source , that source must meet the vacuum source rules and be sized for the added volume . NFPA 99 also limits or monitors oxygen concentration in the combined system.

WAGD inlets are not interchangeable with vacuum inlets. Master alarms carry a WAGD low signal, and local alarms show low WAGD reserve capacity .

Medical Support Gases: Nitrogen and Instrument Air

Nitrogen NF and instrument air power equipment used in patient care procedures. Medical support gas systems must not carry oxidizing gases other than air, or gases meant for breathing. They may be piped to areas with a support purpose and, where appropriate, to laboratories.

Topic Requirement

Standard pressure 160-185 psi is the standard range for valve and outlet labeling; other pressures must be labeled

Outlet performance (verifier test) 5.0 SCFM (140 SLPM) with no more than a 5 psi drop, at a static pressure of 160-185 psi

Instrument air dew point alarm Above -22°F (-30°C) at line pressure, local and master

Instrument air reserve capacity Local alarm when a multi-compressor source could not handle demand if one compressor stopped

Instrument air standby header Cylinders for 1 hour of normal operation ; CGA V-1 medical air connectors ; enters upstream of the final line filters ; serves automatically if the compressor fails

Cylinder storage Instrument air reserve cylinders may share a room with an instrument air compressor if it is the only machinery in the room

  • Outlets Above 80 psi, DISS or an adapter-retaining design
  • Category 2 and 3 Vacuum

Category 2 and Category 3 medical-surgical vacuum systems may be simplex if facility staff have an emergency plan for losing vacuum. Category 3 systems also need emergency electrical service per NFPA 99 Section 6.6 and NFPA 70.

Testing Tie-Ins

The installer's 24-hour standing vacuum test holds between 12 in. HgV and full vacuum (Section 7.2).

The verifier confirms each vacuum inlet can draw 3 SCFM while an adjacent inlet stays at or above 12 in. HgV (Section 7.4).

Before use, the verifier tests that the vacuum source system functions properly.