Study guide
1.3 Inductance, Capacitance, Reactance, and Time Constants
ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: DC Theory, Circuit Laws & Passive Components
1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants
2 Chapter 2: Impedance, Resonance & Passive Filters
2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads
3 Chapter 3: Semiconductor Devices & Power Supplies
3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators
4 Chapter 4: Oscillators & Frequency Synthesis
4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies
5 Chapter 5: RF Amplifiers & Linearity
5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion
6 Chapter 6: Modulation & Demodulation
6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols
7 Chapter 7: Transmitters, Mixers & Receivers
7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity
8 Chapter 8: Transmission Lines & Waveguides
8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs
9 Chapter 9: Impedance Matching & Baluns
9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice
10 Chapter 10: Practical Antennas & Arrays
10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns
11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics
11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths
12 Chapter 12: VHF/UHF Propagation & Space Communications
12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)
13 Chapter 13: Test Equipment & RF Measurements
13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters
14 Chapter 14: Advanced RF Analysis & Diagnostics
14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing
15 Chapter 15: Electromagnetic Compatibility & Interference
15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques
16 Chapter 16: Electrical, RF & Station Safety
16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection
1.3 Inductance, Capacitance, Reactance, and Time Constants
Key Takeaways Explain This Topic AI
Inductance ( L L L , in Henries) opposes changes in current via induced back-EMF ( e = − L d i d t e = -L \frac{di}{dt} e = − L d t d i ); coil inductance scales proportionally with the square of the turns count ( N 2 N^2 N 2 ) and core permeability.
Inductive reactance ( X L = 2 π f L X_L = 2\pi f L X L = 2 π f L ) increases linearly with frequency and causes voltage to lead current by 90 ∘ 90^\circ 9 0 ∘ ('ELI'), whereas capacitive reactance ( X C = 1 2 π f C X_C = \frac{1}{2\pi f C} X C = 2 π f C 1 ) decreases inversely with frequency and causes current to lead voltage by 90 ∘ 90^\circ 9 0 ∘ ('ICE').
NP0/C0G ceramics and silver mica suit stable, low-loss RF tuned circuits. Class 2 ceramics commonly provide supply bypassing, while electrolytics provide bulk low-frequency filtering and decoupling; ESR, ESL and the part rating determine useful performance.
The transient response in RC ( τ = R C \tau = RC τ = RC ) and RL ( τ = L / R \tau = L/R τ = L / R ) circuits governs switching delays and filter attack/decay times, reaching 63.2% of final value in one time constant and 99.3% in five time constants.
The RF skin effect forces high-frequency currents into a thin outer conductor layer of depth δ = ρ / ( π f μ ) \delta = \sqrt{\rho / (\pi f \mu)} δ = ρ / ( π f μ ) , increasing AC resistance with the square root of frequency and requiring large surface area or silver plating in high-Q inductors.
Last updated: November 2026
1.3 Inductance, Capacitance, Reactance, and Time Constants
Inductors and capacitors represent the two fundamental reactive components in electronics. Unlike resistors, which convert electrical energy permanently into heat, inductors and capacitors store energy temporarily in magnetic and electrostatic fields, releasing it back to the circuit during alternate portions of the AC cycle. Their frequency-dependent opposition to alternating current—known as reactance—underpins resonant circuits, RF impedance matching networks, filters, oscillators, and transmission line mechanics.
- 1. Inductance and Magnetic Energy Storage
- The Henry and Back-EMF
Inductance ( L L L ) is the property of an electrical conductor or coil that opposes any change in the electric current flowing through it. When current traverses a conductor, it establishes a surrounding magnetic field proportional to the current magnitude. If that current changes with time ( d i / d t di/dt d i / d t ), the collapsing or expanding magnetic field cuts the conductor itself, inducing an electromotive force known as self-induced back-EMF ( e e e ): e = − L d i d t e = -L \frac{di}{dt} e = − L d t d i
This formulation combines Faraday's Law with Lenz's Law . The negative sign indicates that the induced back-EMF always acts in direct opposition to the change in current that produced it:
When circuit current attempts to increase, back-EMF opposes current rise.
When circuit current drops, back-EMF attempts to sustain current flow.
The SI unit of inductance is the Henry ( H \text{H} H ) . A circuit element has an inductance of one Henry when a current changing at a rate of one Ampere per second induces a back-EMF of one Volt across its terminals ( 1 H = 1 V ⋅ s/A 1\text{ H} = 1\text{ V}\cdot\text{s/A} 1 H = 1 V ⋅ s/A ).
In radio frequency engineering, fractional sub-units are standard:
Millihenry ( 1 mH = 10 − 3 H 1\text{ mH} = 10^{-3}\text{ H} 1 mH = 1 0 − 3 H ): Audio filters, power supply smoothing chokes.
Microhenry ( 1 μ H = 10 − 6 H 1\ \mu\text{H} = 10^{-6}\text{ H} 1 μ H = 1 0 − 6 H ): HF band resonant circuits, RF chokes.
Nanohenry ( 1 nH = 10 − 9 H 1\text{ nH} = 10^{-9}\text{ H} 1 nH = 1 0 − 9 H ): VHF, UHF, and microwave inductors, component lead parasitics.
Energy Stored in a Magnetic Field
Energy stored in the magnetic field of an inductor carrying instantaneous current I I I is: W L = 1 2 L ⋅ I 2 [ Joules ] W_L = \frac{1}{2} L \cdot I^2 \quad [\text{Joules}] W L = 2 1 L ⋅ I 2 [ Joules ]
This stored magnetic energy cannot change discontinuously, meaning the current through an inductor cannot change instantaneously .
Magnetic Shielding
A current-carrying conductor produces a surrounding magnetic field; coil turns reinforce it. Low-frequency magnetic interference is difficult to shield with thin copper or aluminium. A high-permeability enclosure, such as suitable steel or mu-metal, offers a low-reluctance path that diverts magnetic flux around the protected circuit. At higher frequencies, induced currents in a conductive shield oppose the penetrating field, with effectiveness depending on thickness and skin depth. Shielding electric fields and shielding low-frequency magnetic fields therefore require different material choices.
- 2. Factors Affecting Inductance and Core Materials
- Solenoid Inductance Formula
For a single-layer cylindrical solenoid coil wound on a non-magnetic or magnetic core, the inductance is given by: L ≈ μ 0 ⋅ μ r ⋅ N 2 ⋅ A l L \approx \frac{\mu_0 \cdot \mu_r \cdot N^2 \cdot A}{l} L ≈ l μ 0 ⋅ μ r ⋅ N 2 ⋅ A
where:
N N N is the total number of turns.
A A A is the cross-sectional core area in square metres ( π r 2 \pi r^2 π r 2 ).
l l l is the physical length of the coil winding in metres.
μ 0 \mu_0 μ 0 is the permeability of free space ( 4 π × 10 − 7 H/m ≈ 1.2566 × 10 − 6 H/m 4\pi \times 10^{-7}\text{ H/m} \approx 1.2566 \times 10^{-6}\text{ H/m} 4 π × 1 0 − 7 H/m ≈ 1.2566 × 1 0 − 6 H/m ).
μ r \mu_r μ r is the relative magnetic permeability of the core material.
Exam Critical Factor: Inductance is proportional to the square of the turns count ( N 2 N^2 N 2 ) . Doubling the number of turns on an identical former quadruples the inductance ( 2 2 = 4 2^2 = 4 2 2 = 4 ). Halving the number of turns reduces inductance to one-quarter ( 0.5 2 = 0.25 0.5^2 = 0.25 0. 5 2 = 0.25 ).
Magnetic Core Materials in Amateur Radio
Core Material Magnetic Behavior Frequency and Loss Selection Typical Amateur Applications
Air core Relative permeability approximately 1; no magnetic saturation. No core loss; winding resistance and self-capacitance still matter. High-power tank coils, VHF filters and antenna loading coils.
Powdered iron Distributed magnetic gap; permeability and DC-bias behavior depend on mix. Select the mix for low loss at the operating frequency and flux level. HF tuned circuits and filter inductors; Mix 2 (red) and Mix 6 (yellow).
NiZn ferrite Examples: Fair-Rite 61 has initial permeability 125; 43 has 800. Low-loss transformer use and lossy EMI suppression have different frequency limits. RF transformers, baluns and suppression chokes using a suitable grade.
MnZn ferrite Examples: Fair-Rite 77 has initial permeability 2000; 75 has 5000. Often used for lower-frequency inductors; suppression grades can remain useful well above 1 MHz. Power magnetics, LF chokes and common-mode RFI suppression.
Toroidal Cores and the Inductance Index ( A L A_L A L )
Toroidal (doughnut-shaped) cores provide a closed magnetic path that greatly reduces external flux and unwanted coupling. Practical windings and their connections still have leakage fields, so a toroid does not guarantee complete isolation between adjacent stages.
Manufacturers publish an Inductance Factor ( A L A_L A L ) for each core type, defined in microhenries per 100 turns (iron powder) or nanohenries per turns-squared (ferrite): L = A L ⋅ N 2 × 10 − 4 ( Iron Powder, A L in μ H / 100 turns ) L = A_L \cdot N^2 \times 10^{-4} \quad (\text{Iron Powder, } A_L \text{ in } \mu\text{H}/100\text{ turns}) L = A L ⋅ N 2 × 1 0 − 4 ( Iron Powder, A L in μ H /100 turns ) N = 100 L A L N = 100 \sqrt{\frac{L}{A_L}} N = 100 A L L
For example, to wind a 10 μ H 10\ \mu\text{H} 10 μ H inductor on a T50-2 iron powder core ( A L = 49 μ H / 100 turns A_L = 49\ \mu\text{H}/100\text{ turns} A L = 49 μ H /100 turns ): N = 100 10 49 = 100 × 0.4518 ≈ 45 turns N = 100 \sqrt{\frac{10}{49}} = 100 \times 0.4518 \approx 45\text{ turns} N = 100 49 10 = 100 × 0.4518 ≈ 45 turns
- 3. Inductor Combinations and Mutual Inductance
- Inductors in Series (Without Magnetic Coupling)
When inductors are separated so their magnetic fields do not interact: L total = L 1 + L 2 + L 3 + ⋯ + L n L_{\text{total}} = L_1 + L_2 + L_3 + \dots + L_n L total = L 1 + L 2 + L 3 + ⋯ + L n
Inductors in Parallel (Without Magnetic Coupling) 1 L total = 1 L 1 + 1 L 2 + ⋯ + 1 L n \frac{1}{L_{\text{total}}} = \frac{1}{L_1} + \frac{1}{L_2} + \dots + \frac{1}{L_n} L total 1 = L 1 1 + L 2 1 + ⋯ + L n 1
For two uncoupled inductors in parallel: L total = L 1 ⋅ L 2 L 1 + L 2 L_{\text{total}} = \frac{L_1 \cdot L_2}{L_1 + L_2} L total = L 1 + L 2 L 1 ⋅ L 2
Mutual Inductance ( M M M ) and Coupling Coefficient ( k k k )
When two coils are positioned in close proximity, magnetic flux from one coil cuts the turns of the other, establishing mutual inductance ( M M M ) : M = k L 1 ⋅ L 2 M = k \sqrt{L_1 \cdot L_2} M = k L 1 ⋅ L 2
where k k k is the dimensionless coupling coefficient ( 0 ≤ k ≤ 1 0 \le k \le 1 0 ≤ k ≤ 1 ):
k = 1.0 k = 1.0 k = 1.0 : Unity coupling; every line of magnetic flux from coil 1 threads coil 2 (ideal iron/ferrite core transformer).
k = 0.0 k = 0.0 k = 0.0 : Complete magnetic isolation (perpendicular orientation or extensive shielding).
When two inductors with mutual coupling are connected in series: L total = L 1 + L 2 ± 2 M L_{\text{total}} = L_1 + L_2 \pm 2M L total = L 1 + L 2 ± 2 M
Series-Aiding ( + 2 M +2M + 2 M ): Coil magnetic flux fields reinforce each other (windings in same direction).
Series-Opposing ( − 2 M -2M − 2 M ): Coil magnetic flux fields oppose and partially cancel each other.
4. Inductive Reactance ( X L X_L X L )
Inductive Reactance ( X L X_L X L ) represents the opposition presented by an inductor to alternating current. It is measured in Ohms ( Ω \Omega Ω ) : X L = 2 π f L = ω L X_L = 2\pi f L = \omega L X L = 2 π f L = ω L
Key physical relationships:
Linear Frequency Dependence: X L X_L X L is directly proportional to frequency ( f f f ). Doubling frequency doubles inductive reactance; halving frequency halves reactance.
Direct Inductance Dependence: X L X_L X L is directly proportional to inductance ( L L L ).
DC Behavior: At direct current ( f = 0 f = 0 f = 0 ), X L = 0 Ω X_L = 0\ \Omega X L = 0 Ω . An ideal inductor behaves as a complete short circuit to DC.
Phase Relationship in Pure Inductors: "ELI"
In a purely inductive circuit, current cannot change instantaneously due to induced back-EMF. As an alternating voltage is applied, current rise is delayed by a quarter of a cycle. Consequently, alternating voltage LEADS alternating current by 90 ∘ 90^\circ 9 0 ∘ (or current lags voltage by 90 ∘ 90^\circ 9 0 ∘ ) .
Standard Mnemonic: ELI — E (voltage/EMF) Leads I (current) in an L (inductor).
Worked Example 1.7: Inductive Reactance across Amateur Bands
Calculate the reactance of a 4.7 μ H 4.7\ \mu\text{H} 4.7 μ H RF choke across three operating frequencies:
At 1.80 MHz 1.80\text{ MHz} 1.80 MHz (160 m band): X L = 2 π × ( 1.80 × 10 6 Hz ) × ( 4.7 × 10 − 6 H ) ≈ 53.16 Ω X_L = 2\pi \times (1.80 \times 10^6\text{ Hz}) \times (4.7 \times 10^{-6}\text{ H}) \approx 53.16\ \Omega X L = 2 π × ( 1.80 × 1 0 6 Hz ) × ( 4.7 × 1 0 − 6 H ) ≈ 53.16 Ω
At 14.20 MHz 14.20\text{ MHz} 14.20 MHz (20 m band): X L = 2 π × ( 14.20 × 10 6 Hz ) × ( 4.7 × 10 − 6 H ) ≈ 419.34 Ω X_L = 2\pi \times (14.20 \times 10^6\text{ Hz}) \times (4.7 \times 10^{-6}\text{ H}) \approx 419.34\ \Omega X L = 2 π × ( 14.20 × 1 0 6 Hz ) × ( 4.7 × 1 0 − 6 H ) ≈ 419.34 Ω
At 146.0 MHz 146.0\text{ MHz} 146.0 MHz (2 m VHF band): X L = 2 π × ( 146.0 × 10 6 Hz ) × ( 4.7 × 10 − 6 H ) ≈ 4311.5 Ω X_L = 2\pi \times (146.0 \times 10^6\text{ Hz}) \times (4.7 \times 10^{-6}\text{ H}) \approx 4311.5\ \Omega X L = 2 π × ( 146.0 × 1 0 6 Hz ) × ( 4.7 × 1 0 − 6 H ) ≈ 4311.5 Ω
Notice that as frequency increases by roughly 80 times from 1.8 MHz 1.8\text{ MHz} 1.8 MHz to 146 MHz 146\text{ MHz} 146 MHz , the reactance increases by the identical factor of 80.
- 5. Capacitance and Electrostatic Energy Storage
- The Farad and Electrostatic Charge
Capacitance ( C C C ) is the property of an arrangement of electrical conductors separated by a non-conducting dielectric to store potential energy in an electrostatic field. When a potential difference ( V V V ) appears across two conducting plates, equal and opposite charges ( + Q +Q + Q and − Q -Q − Q ) accumulate on their surfaces: Q = C ⋅ V ⟺ C = Q V Q = C \cdot V \Longleftrightarrow C = \frac{Q}{V} Q = C ⋅ V ⟺ C = V Q
Differentiating with respect to time yields the fundamental current equation for a capacitor: i ( t ) = d Q d t = C d v d t i(t) = \frac{dQ}{dt} = C \frac{dv}{dt} i ( t ) = d t d Q = C d t d v
Physical Consequence: Electric current through a capacitor is proportional to the rate of change of voltage. If voltage is constant (DC), d v / d t = 0 dv/dt = 0 d v / d t = 0 , so i = 0 i = 0 i = 0 . Hence, a capacitor completely blocks steady direct current , while allowing alternating displacement current to traverse the dielectric.
The SI unit of capacitance is the Farad ( F \text{F} F ) . A capacitor has a capacitance of one Farad when an applied potential of one Volt stores a charge of one Coulomb ( 1 F = 1 C/V 1\text{ F} = 1\text{ C/V} 1 F = 1 C/V ).
Practical fractional sub-units in radio communications include:
Microfarad ( 1 μ F = 10 − 6 F 1\ \mu\text{F} = 10^{-6}\text{ F} 1 μ F = 1 0 − 6 F ): Power supply filtering, audio coupling.
Nanofarad ( 1 nF = 10 − 9 F = 1000 pF 1\text{ nF} = 10^{-9}\text{ F} = 1000\text{ pF} 1 nF = 1 0 − 9 F = 1000 pF ): RF bypassing, IF tuned circuits.
Picofarad ( 1 pF = 10 − 12 F 1\text{ pF} = 10^{-12}\text{ F} 1 pF = 1 0 − 12 F ): HF/VHF resonant circuits, oscillator feedback, neutralisation.
Energy Stored in an Electrostatic Field
Energy stored in the electrostatic field between capacitor plates charged to potential V V V is: W C = 1 2 C ⋅ V 2 [ Joules ] W_C = \frac{1}{2} C \cdot V^2 \quad [\text{Joules}] W C = 2 1 C ⋅ V 2 [ Joules ]
Because stored electrostatic energy cannot change discontinuously, the voltage across a capacitor cannot change instantaneously .
- 6. Physical Factors Governing Capacitance and Dielectric Types
- Parallel-Plate Capacitance Formula
For a two-plate parallel capacitor: C = ε 0 ⋅ ε r ⋅ A d C = \frac{\varepsilon_0 \cdot \varepsilon_r \cdot A}{d} C = d ε 0 ⋅ ε r ⋅ A
where:
A A A is the overlapping surface area of the conductive plates ( m 2 \text{m}^2 m 2 ).
d d d is the dielectric separation thickness (distance between plates in metres).
ε 0 \varepsilon_0 ε 0 is the permittivity of free space ( 8.8542 × 10 − 12 F/m 8.8542 \times 10^{-12}\text{ F/m} 8.8542 × 1 0 − 12 F/m ).
ε r \varepsilon_r ε r is the relative permittivity (dielectric constant) of the insulating medium.
To increase capacitance:
Increase plate area A A A (e.g. multi-layer interdigitated construction).
Decrease plate separation d d d (limited by dielectric breakdown voltage).
Use a dielectric with high relative permittivity ε r \varepsilon_r ε r .
Capacitor Dielectrics and RF Applicability
Dielectric Material Important Electrical Characteristics RF Suitability Typical Amateur Applications
Air Relative permittivity approximately 1; capacitance depends on plate geometry and spacing. Low dielectric loss; voltage capability depends on clearances and construction. Variable tuning capacitors, ATUs and transmitter tank circuits.
Silver mica Stable capacitance, low loss and high insulation resistance. Suitable for high-Q RF circuits; use the part's voltage and current ratings. Oscillators, tuned circuits and transmitter filters.
Ceramic Class 1: NP0/C0G Low loss; temperature coefficient 0 ± 30 ppm / ∘ C 0\pm30\text{ ppm}/^\circ\text{C} 0 ± 30 ppm / ∘ C . Well suited to stable HF/VHF tuning and matching. Resonant circuits, crystal-filter matching and oscillator feedback.
Ceramic Class 2: X7R, Y5V High capacitance per volume; capacitance varies with temperature and applied voltage. Useful for supply bypassing; unsuitable for precision frequency-setting tanks. Supply decoupling and general bypassing.
Polyester / polypropylene Film capacitors offer good insulation; polypropylene has low dielectric loss. Select the construction for the required frequency and pulse duty. Audio coupling, filters and pulse circuits.
Aluminium electrolytic Oxide relative permittivity approximately 9.5; etched area and thin oxide give high capacitance. ESR/ESL limit high-frequency bypassing; observe polarity and rated voltage. Bulk power-supply smoothing and low-frequency decoupling.
- 7. Capacitor Combinations
- Capacitors in Parallel
When capacitors are connected in parallel across common nodes, their plate surface areas effectively combine: C total = C 1 + C 2 + C 3 + ⋯ + C n C_{\text{total}} = C_1 + C_2 + C_3 + \dots + C_n C total = C 1 + C 2 + C 3 + ⋯ + C n
Total charge is the sum of individual charges ( Q total = Q 1 + Q 2 + … Q_{\text{total}} = Q_1 + Q_2 + \dots Q total = Q 1 + Q 2 + … ). The working voltage rating of the parallel group is limited by the lowest voltage rating among the connected capacitors.
Capacitors in Series
When capacitors are connected in series, the effective dielectric separation thickness increases: 1 C total = 1 C 1 + 1 C 2 + ⋯ + 1 C n \frac{1}{C_{\text{total}}} = \frac{1}{C_1} + \frac{1}{C_2} + \dots + \frac{1}{C_n} C total 1 = C 1 1 + C 2 1 + ⋯ + C n 1
For two capacitors in series: C total = C 1 ⋅ C 2 C 1 + C 2 C_{\text{total}} = \frac{C_1 \cdot C_2}{C_1 + C_2} C total = C 1 + C 2 C 1 ⋅ C 2
The total capacitance of any series combination is always strictly less than the smallest capacitor in the chain.
Voltage Distribution across Series Capacitors
Because the same displacement current passes through each capacitor, identical charge Q Q Q accumulates on each element ( Q = C 1 V 1 = C 2 V 2 Q = C_1 V_1 = C_2 V_2 Q = C 1 V 1 = C 2 V 2 ). The voltage drops divide inversely proportional to capacitance: V 1 V 2 = C 2 C 1 \frac{V_1}{V_2} = \frac{C_2}{C_1} V 2 V 1 = C 1 C 2
The smaller capacitor drops the larger fraction of total voltage.
Safety Note: Series electrolytics increase voltage capability, but each part must stay within its rating under worst-case DC voltage, ripple and sharing imbalance. Four 450 V 450\text{ V} 450 V parts sum to 1800 V 1800\text{ V} 1800 V of ratings; the working-bank voltage needs design margin. Equalising resistors across each capacitor require leakage-based resistance selection, tight tolerance and adequate voltage and power ratings.
8. Capacitive Reactance ( X C X_C X C )
Capacitive Reactance ( X C X_C X C ) represents the opposition presented by a capacitor to alternating current. It is measured in Ohms ( Ω \Omega Ω ) : X C = 1 2 π f C = 1 ω C X_C = \frac{1}{2\pi f C} = \frac{1}{\omega C} X C = 2 π f C 1 = ω C 1
Key physical relationships:
Inverse Frequency Dependence: X C X_C X C is inversely proportional to frequency ( f f f ). Doubling frequency cuts capacitive reactance in half; halving frequency doubles reactance.
Inverse Capacitance Dependence: X C X_C X C is inversely proportional to capacitance ( C C C ).
DC Behavior: At direct current ( f = 0 f = 0 f = 0 ), X C → ∞ Ω X_C \to \infty\ \Omega X C → ∞ Ω . An ideal capacitor represents an open circuit to DC.
Phase Relationship in Pure Capacitors: "ICE"
When an alternating voltage is applied across an uncharged capacitor, maximum charging current flows at the instant voltage crosses zero ( d v / d t dv/dt d v / d t is maximum). As the capacitor charges to peak voltage, current falls to zero. Consequently, alternating current LEADS alternating voltage by 90 ∘ 90^\circ 9 0 ∘ (or voltage lags current by 90 ∘ 90^\circ 9 0 ∘ ) .
Standard Mnemonic: ICE — I (current) Leads C (capacitance) across E (voltage/EMF).
Combining both mnemonics yields the universal engineering rule: E L I the I C E m a n \mathbf{ELI} \quad \text{the} \quad \mathbf{ICE} \quad \mathbf{man} ELI the ICE man
In an Inductor ( L L L ): Voltage ( E E E ) leads Current ( I I I ).
In a Capacitor ( C C C ): Current ( I I I ) leads Voltage ( E E E ).
Worked Example 1.8: Receiver RF Decoupling Sizing
An RF amplifier in a 20-metre receiver operating at 14.10 MHz 14.10\text{ MHz} 14.10 MHz requires a decoupling capacitor between the DC supply rail and ground to bypass stray RF currents. The designer evaluates a 100 nF 100\text{ nF} 100 nF ( 0.1 μ F 0.1\ \mu\text{F} 0.1 μ F ) ceramic capacitor:
Calculate reactance at operating frequency f = 14.10 MHz f = 14.10\text{ MHz} f = 14.10 MHz : X C = 1 2 π × ( 14.10 × 10 6 Hz ) × ( 100 × 10 − 9 F ) = 1 8.859 ≈ 0.1129 Ω X_C = \frac{1}{2\pi \times (14.10 \times 10^6\text{ Hz}) \times (100 \times 10^{-9}\text{ F})} = \frac{1}{8.859} \approx 0.1129\ \Omega X C = 2 π × ( 14.10 × 1 0 6 Hz ) × ( 100 × 1 0 − 9 F ) 1 = 8.859 1 ≈ 0.1129 Ω
Calculate reactance of the same capacitor to an unwanted 100 Hz 100\text{ Hz} 100 Hz power supply ripple: X C = 1 2 π × 100 Hz × ( 100 × 10 − 9 F ) = 1 6.283 × 10 − 5 ≈ 15915 Ω ≈ 15.92 k Ω X_C = \frac{1}{2\pi \times 100\text{ Hz} \times (100 \times 10^{-9}\text{ F})} = \frac{1}{6.283 \times 10^{-5}} \approx 15915\ \Omega \approx 15.92\ \text{k}\Omega X C = 2 π × 100 Hz × ( 100 × 1 0 − 9 F ) 1 = 6.283 × 1 0 − 5 1 ≈ 15915 Ω ≈ 15.92 k Ω
The ideal capacitive reactance is only about 0.11 Ω 0.11\ \Omega 0.11 Ω at 14.1 MHz 14.1\text{ MHz} 14.1 MHz but 15.92 k Ω 15.92\text{ k}\Omega 15.92 k Ω at 100 Hz 100\text{ Hz} 100 Hz . Effective RF bypassing also requires low ESR/ESL and short, low-inductance connections; the ideal reactance alone does not establish the installed impedance.
9. Transient Response and Time Constants
When a DC step voltage is applied to an RC or RL network, the voltages and currents do not change instantaneously but transition exponentially toward steady state.
The RC Time Constant
For a series resistor-capacitor circuit, the time constant ( τ \tau τ , Greek letter tau) is: τ = R ⋅ C [ seconds ] \tau = R \cdot C \quad [\text{seconds}] τ = R ⋅ C [ seconds ]
During capacitor charging from a source V in V_{\text{in}} V in through resistor R R R : v C ( t ) = V in ( 1 − e − t / τ ) , i ( t ) = V in R e − t / τ v_C(t) = V_{\text{in}} \left(1 - e^{-t/\tau}\right), \quad i(t) = \frac{V_{\text{in}}}{R} e^{-t/\tau} v C ( t ) = V in ( 1 − e − t / τ ) , i ( t ) = R V in e − t / τ
During capacitor discharge through resistance R R R from initial voltage V 0 V_0 V 0 : v C ( t ) = V 0 ⋅ e − t / τ v_C(t) = V_0 \cdot e^{-t/\tau} v C ( t ) = V 0 ⋅ e − t / τ
The RL Time Constant
For a series resistor-inductor circuit, the time constant is: τ = L R [ seconds ] \tau = \frac{L}{R} \quad [\text{seconds}] τ = R L [ seconds ]
During current rise across an inductor from source V in V_{\text{in}} V in through resistance R R R : i L ( t ) = V in R ( 1 − e − t / τ ) , v L ( t ) = V in ⋅ e − t / τ i_L(t) = \frac{V_{\text{in}}}{R} \left(1 - e^{-t/\tau}\right), \quad v_L(t) = V_{\text{in}} \cdot e^{-t/\tau} i L ( t ) = R V in ( 1 − e − t / τ ) , v L ( t ) = V in ⋅ e − t / τ
Time Constant Progression Milestones
Elapsed Time ( t t t ) Charging Factor ( 1 − e − t / τ 1 - e^{-t/\tau} 1 − e − t / τ ) Discharging Factor ( e − t / τ e^{-t/\tau} e − t / τ ) Operational Significance
1 τ 1\tau 1 τ 63.2 % 63.2\% 63.2% ( 0.6321 0.6321 0.6321 ) 36.8 % 36.8\% 36.8% ( 0.3679 0.3679 0.3679 ) Primary definition of circuit time constant
2 τ 2\tau 2 τ 86.5 % 86.5\% 86.5% ( 0.8647 0.8647 0.8647 ) 13.5 % 13.5\% 13.5% ( 0.1353 0.1353 0.1353 ) Intermediate transient state
3 τ 3\tau 3 τ 95.0 % 95.0\% 95.0% ( 0.9502 0.9502 0.9502 ) 5.0 % 5.0\% 5.0% ( 0.0498 0.0498 0.0498 ) Approaching steady state
4 τ 4\tau 4 τ 98.2 % 98.2\% 98.2% ( 0.9817 0.9817 0.9817 ) 1.8 % 1.8\% 1.8% ( 0.0183 0.0183 0.0183 ) Residual transient negligible in most systems
5 τ 5\tau 5 τ 99.3 % 99.3\% 99.3% ( 0.9933 0.9933 0.9933 ) 0.7 % 0.7\% 0.7% ( 0.0067 0.0067 0.0067 ) Conventionally considered fully charged / discharged
Amateur Applications of Time Constants
CW Key-Click Shaping: Abrupt carrier switching produces wide keying sidebands. An RC network rounds the edges; its 10–90% step rise time is about 2.2 τ 2.2\tau 2.2 τ , so τ = 4 \tau=4 τ = 4 – 5 ms 5\text{ ms} 5 ms gives roughly 9 9 9 – 11 ms 11\text{ ms} 11 ms . Shaping reduces key clicks, but bandwidth compliance must be checked for the actual keying speed and transmitted waveform.
Automatic Gain Control (AGC): AGC circuits in communications receivers use asymmetrical time constants: a fast attack (typically τ ≈ 1 \tau \approx 1 τ ≈ 1 to 5 ms 5\text{ ms} 5 ms ) to clamp sudden strong incoming signal peaks, combined with a slow decay (typically τ ≈ 500 \tau \approx 500 τ ≈ 500 to 1000 ms 1000\text{ ms} 1000 ms ) to maintain stable receiver gain between words during SSB voice communications.
10. High-Frequency Skin Effect in RF Conductors
At direct current and low audio frequencies, electric current distributes uniformly across the entire cross-sectional area of a conductor. At radio frequencies, this uniform distribution breaks down completely due to the skin effect .
Physical Mechanism of Skin Effect
An alternating current creates an alternating internal magnetic flux within the body of the conductor itself. This internal flux induces tiny internal circulating eddy currents. By Lenz's Law, these eddy currents oppose the primary current at the center of the conductor and reinforce the primary current near the outer conductor surface. Consequently, charge carriers are forced outward into a thin annular layer along the perimeter.
Skin Depth Equation
The skin depth ( δ \delta δ ) is defined as the depth beneath the conductor surface at which the RF current density drops to 1 / e 1/e 1/ e (approximately 36.8 % 36.8\% 36.8% ) of its surface value: δ = ρ π ⋅ f ⋅ μ \delta = \sqrt{\frac{\rho}{\pi \cdot f \cdot \mu}} δ = π ⋅ f ⋅ μ ρ
where:
ρ \rho ρ is the electrical resistivity of the conductor material ( Ω ⋅ m \Omega\cdot\text{m} Ω ⋅ m ; for annealed copper, ρ ≈ 1.724 × 10 − 8 Ω ⋅ m \rho \approx 1.724 \times 10^{-8}\ \Omega\cdot\text{m} ρ ≈ 1.724 × 1 0 − 8 Ω ⋅ m ).
f f f is the operating frequency in Hertz.
μ \mu μ is the absolute magnetic permeability of the material ( μ = μ 0 μ r \mu = \mu_0 \mu_r μ = μ 0 μ r ).
For copper at room temperature, this simplifies to: δ copper ≈ 0.0661 f [ metres ] \delta_{\text{copper}} \approx \frac{0.0661}{\sqrt{f}} \quad [\text{metres}] δ copper ≈ f 0.0661 [ metres ]
Copper Skin Depth across Radio Frequencies
Frequency Operating Band Copper Skin Depth ( δ \delta δ ) Conductor Impact
50 Hz 50\text{ Hz} 50 Hz AC Mains 9.35 mm 9.35\text{ mm} 9.35 mm ( 9350 μ m 9350\ \mu\text{m} 9350 μ m ) Current distributes uniformly through standard household wiring
1.8 MHz 1.8\text{ MHz} 1.8 MHz 160 m HF Band 49.3 μ m 49.3\ \mu\text{m} 49.3 μ m ( 0.049 mm 0.049\text{ mm} 0.049 mm ) Center of thick copper wire is unused
14.1 MHz 14.1\text{ MHz} 14.1 MHz 20 m HF Band 17.6 μ m 17.6\ \mu\text{m} 17.6 μ m ( 0.018 mm 0.018\text{ mm} 0.018 mm ) Current confined to outer 18 μ m 18\ \mu\text{m} 18 μ m skin
146 MHz 146\text{ MHz} 146 MHz 2 m VHF Band 5.47 μ m 5.47\ \mu\text{m} 5.47 μ m ( 0.0055 mm 0.0055\text{ mm} 0.0055 mm ) Current flows entirely in microscopic surface layer
435 MHz 435\text{ MHz} 435 MHz 70 cm UHF Band 3.17 μ m 3.17\ \mu\text{m} 3.17 μ m ( 0.0032 mm 0.0032\text{ mm} 0.0032 mm ) Surface finish and plating dominate conductor resistance
1296 MHz 1296\text{ MHz} 1296 MHz 23 cm Microwave Band 1.84 μ m 1.84\ \mu\text{m} 1.84 μ m ( 0.0018 mm 0.0018\text{ mm} 0.0018 mm ) RF current travels within microscopic surface envelope
Practical Engineering Implications in Amateur Radio
High AC Resistance ( R AC R_{\text{AC}} R AC ): Because the effective cross-sectional area through which current flows is restricted to a thin surface layer, the AC resistance of an inductor or antenna conductor increases proportionally with the square root of frequency ( R AC ∝ f R_{\text{AC}} \propto \sqrt{f} R AC ∝ f ): R AC ≈ R DC ⋅ r 0 2 δ R_{\text{AC}} \approx R_{\text{DC}} \cdot \frac{r_0}{2\delta} R AC ≈ R DC ⋅ 2 δ r 0
Hollow Tubing for Antennas and Coils: Because high-frequency currents do not penetrate the interior of a conductor, hollow copper tubing exhibits the same RF resistance as solid copper rod of the identical outside diameter. High-power transmitter tank coils and Yagi antenna elements are constructed from lightweight, rigid hollow tubing.
Silver Plating: Silver has slightly lower electrical resistivity than copper ( ρ = 1.59 × 10 − 8 Ω ⋅ m \rho = 1.59 \times 10^{-8}\ \Omega\cdot\text{m} ρ = 1.59 × 1 0 − 8 Ω ⋅ m vs. 1.72 × 10 − 8 Ω ⋅ m 1.72 \times 10^{-8}\ \Omega\cdot\text{m} 1.72 × 1 0 − 8 Ω ⋅ m ). In high-Q VHF and UHF cavity resonators, tank circuits, and coaxial relays, copper surfaces are plated with a thin layer of silver (several skin depths thick) to minimize I 2 R I^2 R I 2 R heat losses.
Litz Wire at Low Frequencies: In the LF and MF bands (e.g. 136 kHz 136\text{ kHz} 136 kHz and 472 kHz 472\text{ kHz} 472 kHz ), coils are wound using Litz wire (bundles of individually insulated fine strands woven together). Each strand is engineered to be smaller than the skin depth, forcing uniform current sharing. Above ∼ 2 MHz \sim 2\text{ MHz} ∼ 2 MHz , inter-strand capacitive coupling degrades Litz wire performance, making solid tubing superior.