Study guide

9.1 Lumped-Element Matching Networks and Antenna Tuning Units

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

9.1 Lumped-Element Matching Networks and Antenna Tuning Units

Key Takeaways Explain This Topic AI

Maximum power transfer between an RF source and load requires conjugate matching ( Z source = Z load ∗ Z_{\text{source}} = Z_{\text{load}}^* Z source ​ = Z load ∗ ​ ), where source and load resistances are equal ( R in = R out R_{\text{in}} = R_{\text{out}} R in ​ = R out ​ ) and reactances cancel ( X in = − X out X_{\text{in}} = -X_{\text{out}} X in ​ = − X out ​ ).

L-networks use two reactive components. For real terminating resistances, Q = R high / R low − 1 Q=\sqrt{R_{\text{high}}/R_{\text{low}}-1} Q = R high ​ / R low ​ − 1 ​ is fixed; loss also depends on component quality and the required transformation.

A low-pass Pi network uses two shunt capacitors and a series inductor. Its virtual resistance permits selection of design Q above the corresponding L-network minimum; harmonic rejection depends on the complete circuit.

T-networks employ two series capacitors and a shunt inductor, providing an exceptionally wide matching range for amateur ATUs but functioning as a high-pass network that passes transmitter harmonics without attenuation.

Installing an antenna tuning unit at the antenna feedpoint eliminates standing waves and high SWR losses on the transmission line, whereas a shack-located ATU only provides a conjugate match to protect the transmitter.

Last updated: November 2026

9.1 Lumped-Element Matching Networks and Antenna Tuning Units

In radio frequency (RF) engineering, generating RF energy efficiently is only half the challenge; transferring that energy from active devices (valves or bipolar/MOSFET power transistors) through transmission lines into radiating antenna systems without destructive reflections requires precise impedance transformation. Because the natural radiation resistance and reactive component of an antenna rarely equal the standard 50 Ω 50\ \Omega 50 Ω characteristic impedance of modern transceivers and coaxial feedlines across an entire operating band, impedance matching networks are indispensable. Understanding the mathematical design, operational bandwidth, component stress, and physical placement of matching networks is central to advanced amateur radio theory.

The Conjugate Matching Principle

The fundamental criterion governing maximum power transfer in alternating current (AC) and radio frequency circuits is the Conjugate Matching Principle , derived from the Maximum Power Transfer Theorem extended to the complex impedance domain.

Consider an RF source possessing an internal output impedance Z source = R S + j X S Z_{\text{source}} = R_S + jX_S Z source ​ = R S ​ + j X S ​ delivering power to a terminating load impedance Z load = R L + j X L Z_{\text{load}} = R_L + jX_L Z load ​ = R L ​ + j X L ​ : +----[ R_S ]----[ jX_S ]----[ R_L ]----[ jX_L ]----+

  • | |
  • (~) V_source |
  • | |
  • +--------------------------------------------------+

Use RMS voltage and current phasors in the following power calculation.

The current circulating through the total series loop is: I = V source ( R S + R L ) + j ( X S + X L ) I = \frac{V_{\text{source}}}{(R_S + R_L) + j(X_S + X_L)} I = ( R S ​ + R L ​ ) + j ( X S ​ + X L ​ ) V source ​ ​

The active power dissipated in the resistive portion of the load is: P L = ∣ I ∣ 2 R L = V source 2 R L ( R S + R L ) 2 + ( X S + X L ) 2 P_L = |I|^2 R_L = \frac{V_{\text{source}}^2 R_L}{(R_S + R_L)^2 + (X_S + X_L)^2} P L ​ = ∣ I ∣ 2 R L ​ = ( R S ​ + R L ​ ) 2 + ( X S ​ + X L ​ ) 2 V source 2 ​ R L ​ ​

To maximize this power expression:

The reactive term ( X S + X L ) 2 (X_S + X_L)^2 ( X S ​ + X L ​ ) 2 in the denominator must be minimized. Because reactive power is non-dissipative and stores energy in magnetic or electric fields, the net loop reactance must equal zero: X L = − X S X_L = -X_S X L ​ = − X S ​ . If the source possesses inductive reactance ( + j X +jX + j X ), the load must present equal capacitive reactance ( − j X -jX − j X ) to establish series resonance at the operating frequency.

With reactances cancelled, maximizing P L = V source 2 R L / ( R S + R L ) 2 P_L = V_{\text{source}}^2 R_L / (R_S + R_L)^2 P L ​ = V source 2 ​ R L ​ / ( R S ​ + R L ​ ) 2 by differentiating with respect to R L R_L R L ​ yields the condition R L = R S R_L = R_S R L ​ = R S ​ .

Combining these conditions defines a complex conjugate match : Z load = Z source ∗ ⟺ R L = R S and X L = − X S Z_{\text{load}} = Z_{\text{source}}^* \iff R_L = R_S \quad \text{and} \quad X_L = -X_S Z load ​ = Z source ∗ ​ ⟺ R L ​ = R S ​ and X L ​ = − X S ​

Practical Requirement in Modern Transceivers

Solid-state transceivers normally feed a nominal 50 + j 0 Ω 50+j0\ \Omega 50 + j 0 Ω load. Output matching networks transform the active devices' required load to that interface. A mismatch can produce excessive device voltage, current or dissipation. Many transmitters reduce output when reflected power is high, but the threshold and protection method depend on the design. An external ATU transforms the impedance at its output to a nominal 50 Ω 50\ \Omega 50 Ω input; the transmitter, tuner and feedline must still operate within their ratings.

Lumped-Element Matching Network Topologies

At High Frequency (HF, 3 − 30 MHz 3-30\text{ MHz} 3 − 30 MHz ), matching networks constructed from discrete inductors ( L L L ) and capacitors ( C C C )—termed lumped elements —are preferred because physical wavelengths ( 10 to 100 meters 10\text{ to }100\text{ meters} 10 to 100 meters ) make distributed transmission-line matching stubs excessively large. Lumped-element networks are classified by their schematic geometry into three primary families: L-networks , Pi ( π \pi π ) networks , and T-networks . L network (shunt at input)

  • Input o----+----[ Series X ]----o Output
  • |
  • [ Shunt X ]
  • |
  • Return o---+-------------------o Return
  • Pi network
  • Input o----+----[ Series X ]---+----o Output
  • | |
  • [ Shunt X1 ] [ Shunt X2 ]
  • | |
  • Return o---+-------------------+----o Return
  • T network
  • Input o----[ Series X1 ]---+----[ Series X2 ]----o Output
  • |
  • [ Shunt X ]
  • |
  • Return o-------------------+--------------------o Return

Connect source across input/return and load across output/return.

L-Networks: Minimum Component Count and Fixed Q

The L-network is the simplest reactive matching circuit, consisting of exactly two elements: one reactive element in series and one reactive element in parallel (shunt).

The Fundamental Q Constraint

For an ideal two-element L-network matching real terminating resistances at one frequency, the circuit quality factor is fixed by their ratio: Q = R high R low − 1 Q = \sqrt{\frac{R_{\text{high}}}{R_{\text{low}}} - 1} Q = R low ​ R high ​ ​ − 1 ​

Because Q Q Q is determined solely by the impedance transformation ratio, the designer has no independent control over circuit bandwidth or harmonic attenuation:

If R high R_{\text{high}} R high ​ and R low R_{\text{low}} R low ​ are close (e.g., matching 50 Ω 50\ \Omega 50 Ω to 35 Ω 35\ \Omega 35 Ω ), Q = 50 / 35 − 1 = 0.429 ≈ 0.65 Q = \sqrt{50/35 - 1} = \sqrt{0.429} \approx 0.65 Q = 50/35 − 1 ​ = 0.429 ​ ≈ 0.65 . The network is broadband but provides negligible harmonic suppression.

If the impedance ratio is large (e.g., matching 50 Ω 50\ \Omega 50 Ω to 1000 Ω 1000\ \Omega 1000 Ω ), Q = 1000 / 50 − 1 = 19 ≈ 4.36 Q = \sqrt{1000/50 - 1} = \sqrt{19} \approx 4.36 Q = 1000/50 − 1 ​ = 19 ​ ≈ 4.36 . The network becomes much narrower in bandwidth.

Component Placement Rules

Important

For an L-network matching two real resistances , connect the shunt reactive element across the higher resistance ( R high R_{\text{high}} R high ​ ). First account for source or load reactance before applying this rule.

Matching Down ( R source > R load R_{\text{source}} > R_{\text{load}} R source ​ > R load ​ ): The shunt element is connected on the source input side ( R source = R high R_{\text{source}} = R_{\text{high}} R source ​ = R high ​ ), and the series element connects to the load.

Matching Up ( R source < R load R_{\text{source}} < R_{\text{load}} R source ​ < R load ​ ): The series element connects to the source, and the shunt element connects across the load ( R load = R high R_{\text{load}} = R_{\text{high}} R load ​ = R high ​ ).

Low-Pass, High-Pass, and Complex-Load Matching

For two real resistances there are four basic arrangements: step-up or step-down, each in low-pass or high-pass form. A low-pass match uses series inductance and shunt capacitance; a high-pass match uses series capacitance and shunt inductance. With complex terminations, existing reactance may be absorbed into an arm or cancelled separately. Added components depend on the complete impedance, not just the ratio of its real parts.

In transmitter output matching, low-pass configurations (series L L L , shunt C C C ) are selected because they attenuate transmitter harmonics ( 2 f 0 , 3 f 0 2f_0, 3f_0 2 f 0 ​ , 3 f 0 ​ ), whereas high-pass configurations pass harmonics unattenuated.

Insertion Loss Advantage

An L-network uses only two components and the minimum circuit Q for this resistance transformation. It can therefore have low loss. Inductor resistance ( r s = ∣ X L ∣ / Q 0 r_s=|X_L|/Q_0 r s ​ = ∣ X L ​ ∣/ Q 0 ​ ), capacitor loss, load impedance and layout determine actual efficiency; component count alone does not establish a fixed percentage.

Pi ( π \pi π ) Networks: Independent Q and Harmonic Suppression

A Pi ( π \pi π ) network consists of three reactive elements: a shunt capacitor at the input ( C 1 C_1 C 1 ​ ), a series inductor ( L L L ), and a shunt capacitor at the output ( C 2 C_2 C 2 ​ ).

Virtual Resistance Concept

The mathematical analysis of a Pi-network models the circuit as two back-to-back L-networks meeting at an imaginary intermediate junction termed the virtual resistance ( R v R_v R v ​ ):

An input L-network steps R source R_{\text{source}} R source ​ down to R v R_v R v ​ .

An output L-network steps R v R_v R v ​ up to R load R_{\text{load}} R load ​ . Input o----+----[ L_1 ]---:----[ L_2 ]---+----o Output

  • | : |
  • [ C_1 ] : [ C_2 ]
  • | : |
  • Return o---+--------------:--------------+----o Return
  • Virtual matching plane

Design both sections to meet at R_v; no R_v resistor is fitted.

L = L_1 + L_2.

Because the virtual resistance must be lower than both terminating resistances ( R v < R S R_v < R_S R v ​ < R S ​ and R v < R L R_v < R_L R v ​ < R L ​ ): R v = R high Q L 2 + 1 R_v = \frac{R_{\text{high}}}{Q_L^2 + 1} R v ​ = Q L 2 ​ + 1 R high ​ ​

Here Q L Q_L Q L ​ is a useful design approximation: the Q of the higher-Q L section, rather than an exact general bandwidth measurement of the assembled network.

Tip

Selecting R v R_v R v ​ controls Pi-network Q, but R v R_v R v ​ must be below both terminating resistances. Thus Q L > R high / R low − 1 Q_L>\sqrt{R_{\text{high}}/R_{\text{low}}-1} Q L ​ > R high ​ / R low ​ − 1 ​ for a three-element realization; the limiting case reduces to an L-network.

Pi Networks in RF Amplifiers

A valve amplifier's required plate load depends on its operating class, supply voltage, current and RF voltage swing. The output network transforms that specified load to the feedline impedance; one plate-load formula does not cover every operating condition.

An effective loaded Q around 10 10 10 – 15 15 15 is common in HF valve output networks. Increasing Q generally increases harmonic attenuation, circulating current and component stress while narrowing bandwidth. Actual loss depends on component Q and load. Neither a particular Q nor this topology guarantees legal spurious-emission levels: the complete transmitter output must satisfy the frequency- and power-dependent class-licence limits at the antenna transmission-line connection.

T-Networks: Broad Matching Range and High-Pass Behavior

A T-network consists of three reactive elements arranged in a "T" configuration: two series elements separated by a central shunt element. In amateur radio antenna tuners, the standard configuration consists of two series variable capacitors ( C 1 , C 2 C_1, C_2 C 1 ​ , C 2 ​ ) and a central shunt variable or tapped inductor ( L L L ) . Input o----[ C_1 ]---+----[ C_2 ]----o Output

  • |
  • [ L ]
  • |
  • Return o-------------+--------------o Return

Source across input/return; Z_load across output/return.

Virtual Resistance in T-Networks

The T-network also operates as two back-to-back L-networks, but unlike the Pi-network, the two series arms meet at a virtual resistance that is HIGHER than either terminating resistance ( R v > R S R_v > R_S R v ​ > R S ​ and R v > R L R_v > R_L R v ​ > R L ​ ): R v = R low ( Q L 2 + 1 ) R_v = R_{\text{low}} (Q_L^2 + 1) R v ​ = R low ​ ( Q L 2 ​ + 1 )

This uses the same larger-L-section approximation for Q L Q_L Q L ​ . The requirement R v > R high R_v>R_{\text{high}} R v ​ > R high ​ again places Q L Q_L Q L ​ above the two-element L-network minimum. The virtual resistance is a design quantity, not a fitted resistor.

Why T-Networks Dominate Manual Amateur ATUs

Extraordinary Impedance Range: The T-network can match 50 Ω 50\ \Omega 50 Ω to loads ranging from under 10 Ω 10\ \Omega 10 Ω to over 1000 Ω 1000\ \Omega 1000 Ω , and can absorb substantial inductive or capacitive reactances (from − j 500 Ω -j500\ \Omega − j 500 Ω to + j 500 Ω +j500\ \Omega + j 500 Ω ). This allows a single manual tuner to match non-resonant dipoles, end-fed wires, and multiband verticals.

Practical Component Realization: Using variable capacitors with moderate capacitance ranges (e.g., 20 to 250 pF 20\text{ to }250\text{ pF} 20 to 250 pF ) and a variable roller inductor ( 0.2 to 25 μ H 0.2\text{ to }25\ \mu\text{H} 0.2 to 25 μ H ), the network covers the entire HF spectrum from 1.8 to 30 MHz 1.8\text{ to }30\text{ MHz} 1.8 to 30 MHz without requiring unrealistically large component values.

The Critical High-Pass Pitfall

Warning

Because the capacitors are in series and the inductor is in shunt to ground, the standard amateur T-network is a HIGH-PASS filter .

It passes high frequencies and harmonics ( 2 f 0 , 3 f 0 , 4 f 0 2f_0, 3f_0, 4f_0 2 f 0 ​ , 3 f 0 ​ , 4 f 0 ​ ) straight through with virtually zero attenuation.

It does NOT provide harmonic suppression. Transmitters feeding a T-network ATU must have sufficient internal low-pass filtering to meet spurious emission regulations.

The "Hot Tuner" Trap: Operator Tuning Errors

Three controls ( C 1 , C 2 , L C_1,C_2,L C 1 ​ , C 2 ​ , L ) allow more than one setting to produce a 1 : 1 1:1 1 : 1 input SWR. These matches need not have the same loss. A high-Q setting can circulate excessive coil current and develop high capacitor voltages even while the transmitter-side SWR looks satisfactory. A low SWR alone is not an efficiency measurement.

Correct Tuning Rule: For the usual capacitor–inductor–capacitor T tuner, use the smallest inductance that still permits a match , generally with the largest practicable capacitances. Follow the tuner's control directions, since dial numbers need not increase with capacitance or inductance. Adjust at the manufacturer's specified low tuning power, then verify the match and component ratings before normal operation.

Antenna Tuning Units (ATU) Operation and Placement

An Antenna Tuning Unit (ATU) , or transmatch, is an adjustable impedance-matching system installed between the transmitter and the radiating load.

Manual vs. Automatic ATUs

Feature Manual ATUs Automatic ATUs (Autotuners)

Tuning Mechanism Human operator adjusting rotary dials / roller inductors Microprocessor-switched binary relay banks

Component Elements Continuous air-variable capacitors and rotary inductors Switched discrete inductors and mica/ceramic capacitors

Binary Weighting N/A (continuous analogue variation) Elements scaled as 1 , 2 , 4 , 8 , 16 , 32 , 64 1, 2, 4, 8, 16, 32, 64 1 , 2 , 4 , 8 , 16 , 32 , 64 (e.g., 0.05 0.05 0.05 to 3.2 μ H 3.2\ \mu\text{H} 3.2 μ H )

Sensing System Manual observation of cross-needle SWR wattmeter Directional coupler with magnitude and phase detectors (e.g., AD8302)

Tuning Speed 15 to 45 seconds 15\text{ to }45\text{ seconds} 15 to 45 seconds 1 to 5 seconds 1\text{ to }5\text{ seconds} 1 to 5 seconds (sub-second from memory lookup)

Power Handling Readily engineered for 1 to 3 kW 1\text{ to }3\text{ kW} 1 to 3 kW continuous Typically 100 to 200 W 100\text{ to }200\text{ W} 100 to 200 W (relay contact limits)

In automatic ATUs, an internal directional coupler extracts forward and reflected voltage samples. Phase and magnitude discriminator circuits determine whether the load is inductive or capacitive, and whether the resistive component is above or below 50 Ω 50\ \Omega 50 Ω . The onboard microcontroller executes a fast binary search or hill-climbing algorithm, toggling relays until reflected power reaches a minimum.

Where to Place the ATU: Shack vs. Antenna Feedpoint

The physical location of the ATU within the transmission system has a decisive effect on overall station efficiency: Scenario A: Shack-Located ATU

  • [ Transceiver ] ===( 1:1 SWR )===> [ ATU ] ========( HIGH SWR on Coax )========> [ Antenna ]
  • <--- High feedline loss and heating --->
  • Scenario B: Remote Feedpoint ATU
  • [ Transceiver ] =================( 1:1 SWR on Entire Coax Run )=================> [ ATU ] -> [ Antenna ]
  • <------------- Minimum matched-line loss (α_0) ------------->

ATU Located in the Shack:

What it does: Presents a nominal 50 + j 0 Ω 50+j0\ \Omega 50 + j 0 Ω input when correctly adjusted. This reduces the mismatch seen by the transmitter; it does not certify the power handling of the complete installation.

What it does NOT do: It does not alter the impedance mismatch between the coaxial feedline and the antenna. Standing waves continue to bounce back and forth between the antenna feedpoint and the ATU output.

Consequences: If the coaxial cable has moderate inherent loss and the antenna SWR is high (e.g., 6 : 1 6:1 6 : 1 or 10 : 1 10:1 10 : 1 ), severe additional power is lost as heat along the entire length of the feedline before ever reaching the antenna.

Remote ATU Located at the Antenna Feedpoint:

What it does: Performs the conjugate impedance transformation directly at the junction between the feedline and the antenna element.

Consequences: Standing waves are completely eliminated from the transmission line! The entire run of coaxial cable operates under a true 1 : 1 1:1 1 : 1 SWR, experiencing only its baseline matched attenuation ( α 0 \alpha_0 α 0 ​ ). Power delivery to the antenna is maximized.

Step-by-Step Worked L-Network Design Calculation

An amateur radio operator operates a short quarter-wave vertical antenna on the 40-meter band at f 0 = 7.15 MHz f_0 = 7.15\text{ MHz} f 0 ​ = 7.15 MHz . Due to ground loss and element shortening, the base feedpoint impedance is measured as a purely resistive R load = 12.5 Ω R_{\text{load}} = 12.5\ \Omega R load ​ = 12.5 Ω . Design a low-pass L-network to match this antenna to a 50.0 Ω 50.0\ \Omega 50.0 Ω transceiver output. Input o----+----[ L = 0.482 uH ]---+

  • | |
  • [ C = 770 pF ] [ R_L = 12.5 ohms ]
  • | |
  • Return o---+-----------------------+

The transmitter connects across input and return.

  • Step 1: Identify Terminating Resistances and Calculate Network Q
  • R high = 50.0 Ω R_{\text{high}} = 50.0\ \Omega R high ​ = 50.0 Ω (transceiver side)

R low = 12.5 Ω R_{\text{low}} = 12.5\ \Omega R low ​ = 12.5 Ω (antenna load side) Q = R high R low − 1 = 50.0 12.5 − 1 = 4 − 1 = 3 ≈ 1.732 Q = \sqrt{\frac{R_{\text{high}}}{R_{\text{low}}} - 1} = \sqrt{\frac{50.0}{12.5} - 1} = \sqrt{4 - 1} = \sqrt{3} \approx 1.732 Q = R low ​ R high ​ ​ − 1 ​ = 12.5 50.0 ​ − 1 ​ = 4 − 1 ​ = 3 ​ ≈ 1.732

Step 2: Determine Component Reactances

Because a low-pass response is required, the network must use a shunt capacitor across the high-resistance side ( 50 Ω 50\ \Omega 50 Ω ) and a series inductor in line with the low-resistance side ( 12.5 Ω 12.5\ \Omega 12.5 Ω ):

Shunt Capacitor Reactance ( X C X_C X C ​ ): X C = R high Q = 50.0 Ω 1.732 ≈ 28.87 Ω X_C = \frac{R_{\text{high}}}{Q} = \frac{50.0\ \Omega}{1.732} \approx 28.87\ \Omega X C ​ = Q R high ​ ​ = 1.732 50.0 Ω ​ ≈ 28.87 Ω

Series Inductor Reactance ( X L X_L X L ​ ): X L = Q × R low = 1.732 × 12.5 Ω ≈ 21.65 Ω X_L = Q \times R_{\text{low}} = 1.732 \times 12.5\ \Omega \approx 21.65\ \Omega X L ​ = Q × R low ​ = 1.732 × 12.5 Ω ≈ 21.65 Ω

Step 3: Calculate Component Values at 7.15 MHz 7.15\text{ MHz} 7.15 MHz C = 1 2 π f 0 X C = 1 2 π × ( 7.15 × 10 6 Hz ) × 28.87 Ω ≈ 7.698 × 10 − 10 F ≈ 770 pF C = \frac{1}{2\pi f_0 X_C} = \frac{1}{2\pi \times (7.15 \times 10^6\text{ Hz}) \times 28.87\ \Omega} \approx 7.698 \times 10^{-10}\text{ F} \approx 770\text{ pF} C = 2 π f 0 ​ X C ​ 1 ​ = 2 π × ( 7.15 × 1 0 6 Hz ) × 28.87 Ω 1 ​ ≈ 7.698 × 1 0 − 10 F ≈ 770 pF L = X L 2 π f 0 = 21.65 Ω 2 π × ( 7.15 × 10 6 Hz ) ≈ 4.819 × 10 − 7 H ≈ 0.482 μ H L = \frac{X_L}{2\pi f_0} = \frac{21.65\ \Omega}{2\pi \times (7.15 \times 10^6\text{ Hz})} \approx 4.819 \times 10^{-7}\text{ H} \approx 0.482\ \mu\text{H} L = 2 π f 0 ​ X L ​ ​ = 2 π × ( 7.15 × 1 0 6 Hz ) 21.65 Ω ​ ≈ 4.819 × 1 0 − 7 H ≈ 0.482 μ H

Step 4: Mathematical Verification via Admittance Conversion

Let us verify that this combination transforms 50 Ω 50\ \Omega 50 Ω into 12.5 Ω 12.5\ \Omega 12.5 Ω :

The parallel combination of R high = 50 Ω R_{\text{high}} = 50\ \Omega R high ​ = 50 Ω and X C = − j 28.87 Ω X_C = -j28.87\ \Omega X C ​ = − j 28.87 Ω has an admittance: Y = 1 50 + j ( 1 28.87 ) = 0.020 + j 0.03464 S Y = \frac{1}{50} + j\left(\frac{1}{28.87}\right) = 0.020 + j0.03464\text{ S} Y = 50 1 ​ + j ( 28.87 1 ​ ) = 0.020 + j 0.03464 S

Converting admittance back to series equivalent impedance ( Z s = 1 / Y Z_s = 1/Y Z s ​ = 1/ Y ): Z s = 0.020 − j 0.03464 0.020 2 + 0.03464 2 = 0.020 − j 0.03464 0.0004 + 0.0012 = 0.020 − j 0.03464 0.0016 = 12.5 − j 21.65 Ω Z_s = \frac{0.020 - j0.03464}{0.020^2 + 0.03464^2} = \frac{0.020 - j0.03464}{0.0004 + 0.0012} = \frac{0.020 - j0.03464}{0.0016} = 12.5 - j21.65\ \Omega Z s ​ = 0.02 0 2 + 0.0346 4 2 0.020 − j 0.03464 ​ = 0.0004 + 0.0012 0.020 − j 0.03464 ​ = 0.0016 0.020 − j 0.03464 ​ = 12.5 − j 21.65 Ω

Adding the series inductor ( + j X L = + j 21.65 Ω +jX_L = +j21.65\ \Omega + j X L ​ = + j 21.65 Ω ): Z in = ( 12.5 − j 21.65 ) + j 21.65 = 12.5 + j 0 Ω Z_{\text{in}} = (12.5 - j21.65) + j21.65 = 12.5 + j0\ \Omega Z in ​ = ( 12.5 − j 21.65 ) + j 21.65 = 12.5 + j 0 Ω

The reactive component cancels completely, presenting an exact conjugate match to the 12.5 Ω 12.5\ \Omega 12.5 Ω load.

Comparison Table: Matching Network Topologies

  • Parameter / Feature L-Network Pi ( π \pi π ) Network T-Network
  • Component Count 2 (1 series, 1 shunt) 3 (1 series, 2 shunt) 3 (2 series, 1 shunt)

Design Q Fixed for real resistances: R high / R low − 1 \sqrt{R_{\text{high}}/R_{\text{low}}-1} R high ​ / R low ​ − 1 ​ Selectable above the L-network minimum Selectable above the L-network minimum

Filtering Type Low-pass or High-pass (depends on configuration) Low-pass (inherent) High-pass (inherent in standard tuner design)

Harmonic Rejection Depends on configuration and Q Low-pass response; verify actual rejection Standard high-pass tuner is not a harmonic filter

Matching Range Moderate (best for known fixed loads) Moderate to wide (ideal for tube PAs) Extremely wide ( 10 Ω 10\ \Omega 10 Ω to > 1000 Ω > 1000\ \Omega > 1000 Ω , reactive)

Insertion Loss Often low; depends on transformation and component Q Depends on loaded Q and component losses Depends strongly on settings, load and component Q

Primary Use Case Fixed single-band antenna matching, mobile whips Valve power amplifier output tanks General-purpose manual amateur ATUs