Study guide

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB)

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB)

Key Takeaways Explain This Topic AI

Amplitude modulation varies the instantaneous envelope of an RF carrier proportionally to an audio modulating signal, generating an unmodulated carrier at f c f_c f c ​ and two symmetric sidebands at f c ± f m f_c \pm f_m f c ​ ± f m ​ , occupying a total RF bandwidth of B = 2 f m , max B = 2 f_{m,\text{max}} B = 2 f m , max ​ .

For single-tone AM, m = V m / V c m=V_m/V_c m = V m ​ / V c ​ . At m > 1 m>1 m > 1 the signed modulation factor crosses zero: ideal AM reverses carrier phase and its envelope folds, distorting envelope detection. Practical negative-peak clipping creates additional transmitted sidebands and splatter.

Total transmitted power in an AM signal is P t = P c ( 1 + m 2 / 2 ) P_t = P_c (1 + m^2 / 2) P t ​ = P c ​ ( 1 + m 2 /2 ) ; at 100% modulation ( m = 1 m = 1 m = 1 ), the carrier absorbs 66.7% ( 2 / 3 2/3 2/3 ) of total power while conveying zero intelligence, with each sideband containing only 16.7% ( 1 / 6 1/6 1/6 ) of the total power.

SSB suppresses the carrier and one redundant sideband, reducing RF bandwidth to the audio-band span and concentrating transmitted RF power in one sideband. Compare AM and SSB using the same power reference; receiver noise reduction alone is not an unconditional audio-SNR gain.

By global amateur operating convention, Lower Sideband (LSB) is standardised on HF bands below 10 MHz 10\text{ MHz} 10 MHz ( 160 m , 80 m , 40 m 160\text{ m}, 80\text{ m}, 40\text{ m} 160 m , 80 m , 40 m ), whereas Upper Sideband (USB) is utilised on bands at and above 10 MHz 10\text{ MHz} 10 MHz ( 20 m , 17 m , 15 m , 12 m , 10 m 20\text{ m}, 17\text{ m}, 15\text{ m}, 12\text{ m}, 10\text{ m} 20 m , 17 m , 15 m , 12 m , 10 m , VHF, and UHF).

Last updated: November 2026

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB)

Modulation is the fundamental process by which information—whether human speech, telegraphy, digital telemetry, or video—is imprinted onto a high-frequency radio frequency (RF) carrier wave suitable for electromagnetic radiation. In the early decades of radio communications, Amplitude Modulation (AM) served as the primary medium for long-distance voice transmission. Although largely superseded in modern amateur communications by Single Sideband (SSB) and narrowband digital modes, the mathematical principles governing amplitude-modulated spectra, sideband power distributions, and non-linear mixing remain foundational to amateur radio engineering.

  • 1. Mathematical Fundamentals of Amplitude Modulation
  • The Time-Domain Waveform

In an amplitude-modulated system, the instantaneous peak voltage of an RF carrier wave is varied linearly in sympathy with the instantaneous amplitude of an information-bearing modulating baseband signal (such as an audio tone or human speech).

Let the unmodulated sinusoidal carrier voltage v c ( t ) v_c(t) v c ​ ( t ) be defined by: v c ( t ) = V c sin ⁡ ( ω c t ) v_c(t) = V_c \sin(\omega_c t) v c ​ ( t ) = V c ​ sin ( ω c ​ t )

where V c V_c V c ​ is the unmodulated carrier peak amplitude and ω c = 2 π f c \omega_c = 2\pi f_c ω c ​ = 2 π f c ​ is the carrier angular frequency in radians per second.

Let a single-tone sinusoidal modulating baseband signal v m ( t ) v_m(t) v m ​ ( t ) be defined by: v m ( t ) = V m sin ⁡ ( ω m t ) v_m(t) = V_m \sin(\omega_m t) v m ​ ( t ) = V m ​ sin ( ω m ​ t )

where V m V_m V m ​ is the peak amplitude of the modulating signal and ω m = 2 π f m \omega_m = 2\pi f_m ω m ​ = 2 π f m ​ is the modulating angular frequency ( f c ≫ f m f_c \gg f_m f c ​ ≫ f m ​ ).

For conventional AM without envelope inversion, the RF envelope V env ( t ) V_{\text{env}}(t) V env ​ ( t ) follows the modulating voltage: V env ( t ) = V c + v m ( t ) = V c + V m sin ⁡ ( ω m t ) V_{\text{env}}(t) = V_c + v_m(t) = V_c + V_m \sin(\omega_m t) V env ​ ( t ) = V c ​ + v m ​ ( t ) = V c ​ + V m ​ sin ( ω m ​ t )

The complete instantaneous voltage of the amplitude-modulated wave v ( t ) v(t) v ( t ) is expressed by multiplying the instantaneous envelope by the carrier sinusoid: v ( t ) = [ V c + V m sin ⁡ ( ω m t ) ] sin ⁡ ( ω c t ) v(t) = [V_c + V_m \sin(\omega_m t)] \sin(\omega_c t) v ( t ) = [ V c ​ + V m ​ sin ( ω m ​ t )] sin ( ω c ​ t )

Factoring out the unmodulated carrier amplitude V c V_c V c ​ : v ( t ) = V c [ 1 + m sin ⁡ ( ω m t ) ] sin ⁡ ( ω c t ) v(t) = V_c [1 + m \sin(\omega_m t)] \sin(\omega_c t) v ( t ) = V c ​ [ 1 + m sin ( ω m ​ t )] sin ( ω c ​ t )

where m m m is the modulation index (also called the modulation factor or depth of modulation).

Frequency Spectrum and Sideband Generation

Applying the trigonometric product-to-sum identity sin ⁡ ( A ) sin ⁡ ( B ) = 1 2 [ cos ⁡ ( A − B ) − cos ⁡ ( A + B ) ] \sin(A)\sin(B) = \frac{1}{2}[\cos(A - B) - \cos(A + B)] sin ( A ) sin ( B ) = 2 1 ​ [ cos ( A − B ) − cos ( A + B )] expands the time-domain equation into three distinct frequency components: v ( t ) = V c sin ⁡ ( ω c t ) + m V c 2 cos ⁡ [ ( ω c − ω m ) t ] − m V c 2 cos ⁡ [ ( ω c + ω m ) t ] v(t) = V_c \sin(\omega_c t) + \frac{m V_c}{2} \cos[(\omega_c - \omega_m)t] - \frac{m V_c}{2} \cos[(\omega_c + \omega_m)t] v ( t ) = V c ​ sin ( ω c ​ t ) + 2 m V c ​ ​ cos [( ω c ​ − ω m ​ ) t ] − 2 m V c ​ ​ cos [( ω c ​ + ω m ​ ) t ]

This expansion reveals that an amplitude-modulated signal does not simply vary in amplitude at the single carrier frequency; rather, it consists of precisely three discrete spectral lines:

The Carrier Component: V c sin ⁡ ( ω c t ) V_c \sin(\omega_c t) V c ​ sin ( ω c ​ t ) , remaining constant in amplitude ( V c V_c V c ​ ) and frequency ( f c f_c f c ​ ), completely independent of the presence or amplitude of modulation.

The Lower Sideband (LSB): m V c 2 cos ⁡ [ 2 π ( f c − f m ) t ] \frac{m V_c}{2} \cos[2\pi (f_c - f_m)t] 2 m V c ​ ​ cos [ 2 π ( f c ​ − f m ​ ) t ] , located at the difference frequency f c − f m f_c - f_m f c ​ − f m ​ .

The Upper Sideband (USB): − m V c 2 cos ⁡ [ 2 π ( f c + f m ) t ] -\frac{m V_c}{2} \cos[2\pi (f_c + f_m)t] − 2 m V c ​ ​ cos [ 2 π ( f c ​ + f m ​ ) t ] , located at the sum frequency f c + f m f_c + f_m f c ​ + f m ​ .

Each sideband has a peak amplitude of m V c 2 \frac{m V_c}{2} 2 m V c ​ ​ . Under 100% modulation ( m = 1 m = 1 m = 1 ), each sideband reaches exactly half the voltage of the unmodulated carrier ( V c / 2 V_c / 2 V c ​ /2 ). Amplitude

  • ^
  • | Carrier (fc)
  • | |
  • Vc | |
  • | LSB | USB
  • | (fc - fm) | (fc + fm)
  • Vc/2 | | |
  • | | | |
  • +----------+---------+---------+---------> Frequency (f)
  • |<-- fm ->|<-- fm ->|
  • |<------ B = 2*fm ----->|
  • AM Bandwidth Requirements

When complex baseband signals such as speech (containing a spectrum of frequencies from f m , min f_{m,\text{min}} f m , min ​ to f m , max f_{m,\text{max}} f m , max ​ ) modulate the carrier, the sidebands expand into continuous spectral bands flanking the carrier. The total occupied RF transmission bandwidth ( B B B ) is strictly twice the highest modulating frequency: B = 2 f m , max B = 2 f_{m,\text{max}} B = 2 f m , max ​

For standard communications-quality speech restricted to an audio bandwidth of 300 Hz 300\text{ Hz} 300 Hz to 3000 Hz 3000\text{ Hz} 3000 Hz ( f m , max = 3 kHz f_{m,\text{max}} = 3\text{ kHz} f m , max ​ = 3 kHz ), the resulting AM signal requires a total RF channel bandwidth of: B = 2 × 3 kHz = 6 kHz B = 2 \times 3\text{ kHz} = 6\text{ kHz} B = 2 × 3 kHz = 6 kHz

  • 2. Modulation Index and Overmodulation Dynamics
  • Defining the Modulation Index ( m m m )

The modulation index quantifies the degree of carrier envelope excursion relative to the quiescent carrier level: m = V m V c m = \frac{V_m}{V_c} m = V c ​ V m ​ ​

When expressed as a percentage, it is termed the percentage of modulation ( M M M ): M = m × 100 % M = m \times 100\% M = m × 100%

For undistorted single-tone AM with 0 ≤ m ≤ 1 0\le m\le1 0 ≤ m ≤ 1 , the maximum and minimum RF envelope voltages are: V max = V c + V m V_{\text{max}} = V_c + V_m V max ​ = V c ​ + V m ​ V min = V c − V m V_{\text{min}} = V_c - V_m V min ​ = V c ​ − V m ​

Adding and subtracting these two relationships yields: V max + V min = 2 V c ⟹ V c = V max + V min 2 V_{\text{max}} + V_{\text{min}} = 2 V_c \implies V_c = \frac{V_{\text{max}} + V_{\text{min}}}{2} V max ​ + V min ​ = 2 V c ​ ⟹ V c ​ = 2 V max ​ + V min ​ ​ V max − V min = 2 V m ⟹ V m = V max − V min 2 V_{\text{max}} - V_{\text{min}} = 2 V_m \implies V_m = \frac{V_{\text{max}} - V_{\text{min}}}{2} V max ​ − V min ​ = 2 V m ​ ⟹ V m ​ = 2 V max ​ − V min ​ ​

Dividing V m V_m V m ​ by V c V_c V c ​ gives the oscilloscope formula for this non-overmodulated single-tone case: m = V max − V min V max + V min m = \frac{V_{\text{max}} - V_{\text{min}}}{V_{\text{max}} + V_{\text{min}}} m = V max ​ + V min ​ V max ​ − V min ​ ​

Operating Regimes: Undermodulation, Complete Modulation, and Overmodulation

Operating Regime Modulation Index RF Envelope Operational Impact

Undermodulation 0 < m < 1 0<m<1 0 < m < 1 Minimum V c ( 1 − m ) > 0 V_c(1-m)>0 V c ​ ( 1 − m ) > 0 Clean envelope detection is possible; sideband power is below its value at m = 1 m=1 m = 1 .

Complete Modulation m = 1 m=1 m = 1 Minimum zero; maximum 2 V c 2V_c 2 V c ​ The limiting depth for undistorted envelope detection of symmetrical single-tone AM.

Overmodulation m > 1 m>1 m > 1 The signed factor crosses zero; the actual envelope is its absolute value An envelope detector distorts the recovered audio. Transmitter clipping can also cause splatter.

For the ideal waveform, distinguish the signed modulation factor from the nonnegative RF envelope: a ( t ) = V c [ 1 + m sin ⁡ ( ω m t ) ] , V env ( t ) = ∣ a ( t ) ∣ a(t)=V_c[1+m\sin(\omega_mt)],\qquad V_{\text{env}}(t)=|a(t)| a ( t ) = V c ​ [ 1 + m sin ( ω m ​ t )] , V env ​ ( t ) = ∣ a ( t ) ∣

At the negative audio peak, a ( t ) / V c a(t)/V_c a ( t ) / V c ​ equals 0.5 0.5 0.5 , 0 0 0 and − 0.5 -0.5 − 0.5 for m = 0.5 m=0.5 m = 0.5 , 1 1 1 and 1.5 1.5 1.5 respectively. In the last case the carrier reverses phase by 180 ∘ 180^\circ 18 0 ∘ while the envelope folds upward. This is not a finite interval of zero RF output in the ideal model.

Consequences of Overmodulation in Amateur Transmitters

An envelope detector follows ∣ a ( t ) ∣ |a(t)| ∣ a ( t ) ∣ , so it cannot recover the original audio faithfully when the signed factor becomes negative. The ideal multiplier waveform still contains the carrier and the two single-tone sidebands; phase reversal alone does not create extra transmitted spectral lines.

A practical high-level AM transmitter may instead reach cutoff during negative peaks and clip the envelope . That nonlinear clipping creates additional harmonics of the audio, which appear as unwanted sidebands around the carrier. They are not restricted to odd harmonics. Excessive microphone gain or inadequate modulator headroom can therefore cause distorted audio and adjacent-channel splatter. Keep the symmetrical sine-wave test within 100 % 100\% 100% modulation and check the actual envelope and spectrum.

  • 3. Power Distribution in AM Signals
  • Mathematical Power Derivation

To understand the fundamental power inefficiency of full-carrier amplitude modulation, consider an AM signal developed across a pure load resistance R R R (such as a 50 Ω 50\ \Omega 50 Ω antenna system).

The unmodulated carrier power ( P c P_c P c ​ ) is the average power dissipated by the carrier alone: P c = V c , rms 2 R = ( V c / 2 ) 2 R = V c 2 2 R P_c = \frac{V_{c,\text{rms}}^2}{R} = \frac{(V_c / \sqrt{2})^2}{R} = \frac{V_c^2}{2R} P c ​ = R V c , rms 2 ​ ​ = R ( V c ​ / 2 ​ ) 2 ​ = 2 R V c 2 ​ ​

Each sideband has a peak voltage of m V c 2 \frac{m V_c}{2} 2 m V c ​ ​ , corresponding to an RMS voltage of: V sb , rms = m V c / 2 2 = m V c 2 2 V_{\text{sb},\text{rms}} = \frac{m V_c / 2}{\sqrt{2}} = \frac{m V_c}{2\sqrt{2}} V sb , rms ​ = 2 ​ m V c ​ /2 ​ = 2 2 ​ m V c ​ ​

The power contained in each individual sideband ( P LSB P_{\text{LSB}} P LSB ​ and P USB P_{\text{USB}} P USB ​ ) is: P LSB = P USB = V sb , rms 2 R = ( m V c / 2 2 ) 2 R = m 2 V c 2 8 R = m 2 4 ( V c 2 2 R ) = m 2 4 P c P_{\text{LSB}} = P_{\text{USB}} = \frac{V_{\text{sb},\text{rms}}^2}{R} = \frac{(m V_c / 2\sqrt{2})^2}{R} = \frac{m^2 V_c^2}{8R} = \frac{m^2}{4} \left( \frac{V_c^2}{2R} \right) = \frac{m^2}{4} P_c P LSB ​ = P USB ​ = R V sb , rms 2 ​ ​ = R ( m V c ​ /2 2 ​ ) 2 ​ = 8 R m 2 V c 2 ​ ​ = 4 m 2 ​ ( 2 R V c 2 ​ ​ ) = 4 m 2 ​ P c ​

Because the carrier, lower sideband, and upper sideband are mutually orthogonal in frequency, total average power ( P t P_t P t ​ ) is the direct scalar sum of their individual powers: P t = P c + P LSB + P USB = P c + m 2 4 P c + m 2 4 P c = P c ( 1 + m 2 2 ) P_t = P_c + P_{\text{LSB}} + P_{\text{USB}} = P_c + \frac{m^2}{4} P_c + \frac{m^2}{4} P_c = P_c \left( 1 + \frac{m^2}{2} \right) P t ​ = P c ​ + P LSB ​ + P USB ​ = P c ​ + 4 m 2 ​ P c ​ + 4 m 2 ​ P c ​ = P c ​ ( 1 + 2 m 2 ​ )

The total power contained in both intelligence-bearing sidebands ( P SB P_{\text{SB}} P SB ​ ) is: P SB = P LSB + P USB = m 2 2 P c P_{\text{SB}} = P_{\text{LSB}} + P_{\text{USB}} = \frac{m^2}{2} P_c P SB ​ = P LSB ​ + P USB ​ = 2 m 2 ​ P c ​

Power Distribution at 100% Modulation ( m = 1.0 m = 1.0 m = 1.0 )

Substituting m = 1.0 m = 1.0 m = 1.0 into the power equations reveals the dramatic imbalance between carrier and sideband dissipation: P t = P c ( 1 + 1 2 2 ) = 1.5 ⋅ P c P_t = P_c \left( 1 + \frac{1^2}{2} \right) = 1.5 \cdot P_c P t ​ = P c ​ ( 1 + 2 1 2 ​ ) = 1.5 ⋅ P c ​ P SB = 1 2 2 P c = 0.5 ⋅ P c P_{\text{SB}} = \frac{1^2}{2} P_c = 0.5 \cdot P_c P SB ​ = 2 1 2 ​ P c ​ = 0.5 ⋅ P c ​ P LSB = P USB = 1 2 4 P c = 0.25 ⋅ P c P_{\text{LSB}} = P_{\text{USB}} = \frac{1^2}{4} P_c = 0.25 \cdot P_c P LSB ​ = P USB ​ = 4 1 2 ​ P c ​ = 0.25 ⋅ P c ​

Expressing each component as a percentage of total transmitted power ( P t P_t P t ​ ):

Carrier Power Fraction: P c P t = P c 1.5 P c = 2 3 ≈ 66.67 % \frac{P_c}{P_t} = \frac{P_c}{1.5 P_c} = \frac{2}{3} \approx 66.67\% P t ​ P c ​ ​ = 1.5 P c ​ P c ​ ​ = 3 2 ​ ≈ 66.67%

Total Sideband Power Fraction: P SB P t = 0.5 P c 1.5 P c = 1 3 ≈ 33.33 % \frac{P_{\text{SB}}}{P_t} = \frac{0.5 P_c}{1.5 P_c} = \frac{1}{3} \approx 33.33\% P t ​ P SB ​ ​ = 1.5 P c ​ 0.5 P c ​ ​ = 3 1 ​ ≈ 33.33%

Individual Sideband Power Fraction (each): P LSB P t = P USB P t = 0.25 P c 1.5 P c = 1 6 ≈ 16.67 % \frac{P_{\text{LSB}}}{P_t} = \frac{P_{\text{USB}}}{P_t} = \frac{0.25 P_c}{1.5 P_c} = \frac{1}{6} \approx 16.67\% P t ​ P LSB ​ ​ = P t ​ P USB ​ ​ = 1.5 P c ​ 0.25 P c ​ ​ = 6 1 ​ ≈ 16.67%

Core Engineering Insight: At 100% modulation, exactly two-thirds ( 66.7 % 66.7\% 66.7% ) of the total RF power radiated by the antenna is locked in the carrier wave. The carrier contains zero information —its frequency, amplitude, and phase never change with modulation. Furthermore, the remaining one-third ( 33.3 % 33.3\% 33.3% ) of the power is split equally between two redundant sidebands. Thus, a single sideband carries only 16.7 % 16.7\% 16.7% of total transmitter power.

  • 4. Worked Calculation: AM Power and Modulation Depth
  • Worked Example 6.1: Full AM Power and Voltage Analysis

An amateur AM transmitter delivers an unmodulated carrier power of 100 W 100\text{ W} 100 W into a matched 50.0 Ω 50.0\ \Omega 50.0 Ω dummy load. The transmitter is subsequently modulated by a pure 1000 Hz 1000\text{ Hz} 1000 Hz sine wave.

Determine the unmodulated carrier peak voltage ( V c V_c V c ​ ) and peak-to-peak voltage ( V p-p V_{\text{p-p}} V p-p ​ ): V c , rms = P c ⋅ R = 100 W × 50.0 Ω = 5000 ≈ 70.71 V V_{c,\text{rms}} = \sqrt{P_c \cdot R} = \sqrt{100\text{ W} \times 50.0\ \Omega} = \sqrt{5000} \approx 70.71\text{ V} V c , rms ​ = P c ​ ⋅ R ​ = 100 W × 50.0 Ω ​ = 5000 ​ ≈ 70.71 V V c = 2 ⋅ V c , rms = 2 × 70.71 V = 100.0 V V_c = \sqrt{2} \cdot V_{c,\text{rms}} = \sqrt{2} \times 70.71\text{ V} = 100.0\text{ V} V c ​ = 2 ​ ⋅ V c , rms ​ = 2 ​ × 70.71 V = 100.0 V V p-p(unmod) = 2 ⋅ V c = 200.0 V V_{\text{p-p(unmod)}} = 2 \cdot V_c = 200.0\text{ V} V p-p(unmod) ​ = 2 ⋅ V c ​ = 200.0 V

Calculate the total power, sideband power, and envelope peak values at m = 0.70 m = 0.70 m = 0.70 (70% modulation): P t = P c ( 1 + m 2 2 ) = 100 W × ( 1 + 0.70 2 2 ) = 100 × ( 1 + 0.245 ) = 124.5 W P_t = P_c \left( 1 + \frac{m^2}{2} \right) = 100\text{ W} \times \left( 1 + \frac{0.70^2}{2} \right) = 100 \times (1 + 0.245) = 124.5\text{ W} P t ​ = P c ​ ( 1 + 2 m 2 ​ ) = 100 W × ( 1 + 2 0.7 0 2 ​ ) = 100 × ( 1 + 0.245 ) = 124.5 W P SB = P t − P c = 124.5 W − 100.0 W = 24.5 W P_{\text{SB}} = P_t - P_c = 124.5\text{ W} - 100.0\text{ W} = 24.5\text{ W} P SB ​ = P t ​ − P c ​ = 124.5 W − 100.0 W = 24.5 W P LSB = P USB = 24.5 W 2 = 12.25 W P_{\text{LSB}} = P_{\text{USB}} = \frac{24.5\text{ W}}{2} = 12.25\text{ W} P LSB ​ = P USB ​ = 2 24.5 W ​ = 12.25 W

Envelope peak voltage: V max = V c ( 1 + m ) = 100 V × ( 1 + 0.70 ) = 170.0 V V_{\text{max}} = V_c (1 + m) = 100\text{ V} \times (1 + 0.70) = 170.0\text{ V} V max ​ = V c ​ ( 1 + m ) = 100 V × ( 1 + 0.70 ) = 170.0 V V min = V c ( 1 − m ) = 100 V × ( 1 − 0.70 ) = 30.0 V V_{\text{min}} = V_c (1 - m) = 100\text{ V} \times (1 - 0.70) = 30.0\text{ V} V min ​ = V c ​ ( 1 − m ) = 100 V × ( 1 − 0.70 ) = 30.0 V

Peak Envelope Power (PEP): PEP = ( V max / 2 ) 2 R = V max 2 2 R = 170.0 2 2 × 50.0 = 28900 100 = 289.0 W \text{PEP} = \frac{(V_{\text{max}} / \sqrt{2})^2}{R} = \frac{V_{\text{max}}^2}{2R} = \frac{170.0^2}{2 \times 50.0} = \frac{28900}{100} = 289.0\text{ W} PEP = R ( V max ​ / 2 ​ ) 2 ​ = 2 R V max 2 ​ ​ = 2 × 50.0 170. 0 2 ​ = 100 28900 ​ = 289.0 W

Calculate the operating parameters at m = 1.0 m = 1.0 m = 1.0 (100% modulation): P t = 100 W × ( 1 + 1.0 2 2 ) = 150.0 W P_t = 100\text{ W} \times \left( 1 + \frac{1.0^2}{2} \right) = 150.0\text{ W} P t ​ = 100 W × ( 1 + 2 1. 0 2 ​ ) = 150.0 W P LSB = P USB = 0.25 × 100 W 1 = 25.0 W P_{\text{LSB}} = P_{\text{USB}} = \frac{0.25 \times 100\text{ W}}{1} = 25.0\text{ W} P LSB ​ = P USB ​ = 1 0.25 × 100 W ​ = 25.0 W V max = 100 V × ( 1 + 1.0 ) = 200.0 V V_{\text{max}} = 100\text{ V} \times (1 + 1.0) = 200.0\text{ V} V max ​ = 100 V × ( 1 + 1.0 ) = 200.0 V V min = 100 V × ( 1 − 1.0 ) = 0.0 V V_{\text{min}} = 100\text{ V} \times (1 - 1.0) = 0.0\text{ V} V min ​ = 100 V × ( 1 − 1.0 ) = 0.0 V PEP = V max 2 2 R = 200.0 2 100 = 400.0 W \text{PEP} = \frac{V_{\text{max}}^2}{2R} = \frac{200.0^2}{100} = 400.0\text{ W} PEP = 2 R V max 2 ​ ​ = 100 200. 0 2 ​ = 400.0 W

Notice that at 100% modulation, the Peak Envelope Power (PEP) is precisely four times the unmodulated carrier power ( 400 W 400\text{ W} 400 W vs 100 W 100\text{ W} 100 W ), and the peak voltage doubles ( 200 V 200\text{ V} 200 V vs 100 V 100\text{ V} 100 V ). An amplifier designed for AM service must be capable of delivering this 4 × 4\times 4 × peak power without saturating.

5. Double Sideband Suppressed Carrier (DSB-SC)

Because the carrier in an AM signal consumes 66.7 % 66.7\% 66.7% of total power while carrying no information, an obvious engineering optimization is to suppress the carrier completely prior to transmission. This is known as Double Sideband Suppressed Carrier (DSB-SC) .

Balanced Modulator Operation

A balanced modulator multiplies the audio modulating signal v m ( t ) v_m(t) v m ​ ( t ) directly with the RF carrier v c ( t ) v_c(t) v c ​ ( t ) without adding the carrier offset: v dsb ( t ) = v m ( t ) ⋅ v c ( t ) = [ V m sin ⁡ ( ω m t ) ] ⋅ [ sin ⁡ ( ω c t ) ] v_{\text{dsb}}(t) = v_m(t) \cdot v_c(t) = [V_m \sin(\omega_m t)] \cdot [\sin(\omega_c t)] v dsb ​ ( t ) = v m ​ ( t ) ⋅ v c ​ ( t ) = [ V m ​ sin ( ω m ​ t )] ⋅ [ sin ( ω c ​ t )]

Applying the product-to-sum identity: v dsb ( t ) = V m 2 cos ⁡ [ ( ω c − ω m ) t ] − V m 2 cos ⁡ [ ( ω c + ω m ) t ] v_{\text{dsb}}(t) = \frac{V_m}{2} \cos[(\omega_c - \omega_m)t] - \frac{V_m}{2} \cos[(\omega_c + \omega_m)t] v dsb ​ ( t ) = 2 V m ​ ​ cos [( ω c ​ − ω m ​ ) t ] − 2 V m ​ ​ cos [( ω c ​ + ω m ​ ) t ]

The carrier component V c sin ⁡ ( ω c t ) V_c \sin(\omega_c t) V c ​ sin ( ω c ​ t ) is completely absent from the output. In practical balanced modulators—such as a diode ring double-balanced mixer or active Gilbert cell transistor array—the carrier is balanced out by symmetrical circuit topology, typically achieving 40 dB 40\text{ dB} 40 dB to 50 dB 50\text{ dB} 50 dB of carrier suppression. Audio In ------->| Balanced |-------> DSB-SC Output (LSB + USB)

  • | Modulator | (Carrier is suppressed)
  • Carrier In ----->| (Diode Ring)|

While DSB-SC eliminates the carrier power waste (100% of transmitted power resides in the sidebands), it still occupies an RF bandwidth of B = 2 f m , max B = 2 f_{m,\text{max}} B = 2 f m , max ​ ( 6 kHz 6\text{ kHz} 6 kHz for voice), because both upper and lower sidebands are transmitted.

  • 6. Single Sideband Suppressed Carrier (SSB)
  • The Single Sideband Concept

Because the upper and lower sidebands are exact mirror images of each other, conveying identical intelligence, transmitting both sidebands is redundant. Single Sideband Suppressed Carrier (SSB) eliminates both the carrier wave and one of the two sidebands, transmitting exclusively the Upper Sideband (USB) or the Lower Sideband (LSB).

Bandwidth, Noise and Power Comparisons

Bandwidth Conservation: The SSB bandwidth equals the span of the transmitted audio band: B SSB = f m , max − f m , min B_{\text{SSB}}=f_{m,\text{max}}-f_{m,\text{min}} B SSB ​ = f m , max ​ − f m , min ​

Audio from 300 300 300 to 3000 Hz 3000\text{ Hz} 3000 Hz occupies 2.7 kHz 2.7\text{ kHz} 2.7 kHz in one sideband, compared with the full 6 kHz 6\text{ kHz} 6 kHz span of conventional AM. Speech passbands around 2.4 2.4 2.4 to 2.8 kHz 2.8\text{ kHz} 2.8 kHz are common.

Receiver Noise Bandwidth: For white thermal noise, N = k T B N=kTB N = k TB , where B B B is equivalent noise bandwidth. Reducing it from 6.0 6.0 6.0 to 2.4 kHz 2.4\text{ kHz} 2.4 kHz changes admitted noise power by: Δ N = 10 log ⁡ 10 ( 2.4 / 6.0 ) ≈ − 3.98 dB \Delta N=10\log_{10}(2.4/6.0)\approx-3.98\text{ dB} Δ N = 10 lo g 10 ​ ( 2.4/6.0 ) ≈ − 3.98 dB

This is a noise-power comparison. Recovered audio SNR also depends on signal power and demodulation; both AM sidebands contribute to the detected audio.

Use the Same Power Reference: Compare ideal signals at 100 W PEP 100\text{ W PEP} 100 W PEP , using one audio test tone. At 100 % 100\% 100% AM modulation, PEP = 4 P c \text{PEP}=4P_c PEP = 4 P c ​ , so P c = 25 W P_c=25\text{ W} P c ​ = 25 W , average total power is 37.5 W 37.5\text{ W} 37.5 W , and each sideband contains 6.25 W 6.25\text{ W} 6.25 W . A single-tone SSB signal has constant envelope and 100 W 100\text{ W} 100 W average power, all in its one sideband.

For speech, SSB average power is lower than PEP and depends on the waveform and processing. These allocations explain the value of suppressing the carrier and redundant sideband; they do not establish a universal communications gain by adding a sideband-power ratio to a separate noise-bandwidth ratio.

Amateur Radio Sideband Operating Conventions

For SSB voice, the usual amateur operating conventions are:

Lower Sideband (LSB): Utilised on HF bands below 10 MHz 10\text{ MHz} 10 MHz :

  • 160 Metres 160\text{ Metres} 160 Metres ( 1.8 MHz 1.8\text{ MHz} 1.8 MHz )
  • 80 Metres 80\text{ Metres} 80 Metres ( 3.5 MHz 3.5\text{ MHz} 3.5 MHz )
  • 40 Metres 40\text{ Metres} 40 Metres ( 7.0 MHz 7.0\text{ MHz} 7.0 MHz )

Upper Sideband (USB): Utilised on HF bands at and above 10 MHz 10\text{ MHz} 10 MHz , as well as all VHF, UHF, and microwave bands:

30 Metres 30\text{ Metres} 30 Metres ( 10.1 MHz 10.1\text{ MHz} 10.1 MHz ): Australia also has a domestic SSB voice arrangement. Follow the current WIA band plan for its segment and sideband recommendations; the band is not digital/CW only.

  • 20 Metres 20\text{ Metres} 20 Metres ( 14.0 MHz 14.0\text{ MHz} 14.0 MHz )
  • 17 Metres 17\text{ Metres} 17 Metres ( 18.068 MHz 18.068\text{ MHz} 18.068 MHz )
  • 15 Metres 15\text{ Metres} 15 Metres ( 21.0 MHz 21.0\text{ MHz} 21.0 MHz )
  • 12 Metres 12\text{ Metres} 12 Metres ( 24.89 MHz 24.89\text{ MHz} 24.89 MHz )
  • 10 Metres 10\text{ Metres} 10 Metres ( 28.0 MHz 28.0\text{ MHz} 28.0 MHz )

6 Metres 6\text{ Metres} 6 Metres ( 50 MHz 50\text{ MHz} 50 MHz ), 2 Metres 2\text{ Metres} 2 Metres ( 144 MHz 144\text{ MHz} 144 MHz ), 70 cm 70\text{ cm} 70 cm ( 432 MHz 432\text{ MHz} 432 MHz ), and higher.

Frequency Translation and Sideband Inversion: Track each spectral component through the mixer. A USB signal at 9 MHz + f a 9\text{ MHz}+f_a 9 MHz + f a ​ mixed with a 5 MHz 5\text{ MHz} 5 MHz LO gives the sum 14 MHz + f a 14\text{ MHz}+f_a 14 MHz + f a ​ , still USB. Selecting the difference with a 5.2 MHz 5.2\text{ MHz} 5.2 MHz LO gives 3.8 MHz + f a 3.8\text{ MHz}+f_a 3.8 MHz + f a ​ , also USB. In contrast, selecting LO minus input with a 12.8 MHz 12.8\text{ MHz} 12.8 MHz LO gives 3.8 MHz − f a 3.8\text{ MHz}-f_a 3.8 MHz − f a ​ , which is LSB. A difference-frequency output does not automatically imply inversion; which frequency is subtracted matters.

7. Generation of SSB Signals

Two classical architectures exist for eliminating the unwanted sideband and carrier: the Filter Method and the Phasing Method .

The Filter Method

The filter method is the most widely implemented analog architecture in commercial and amateur transceivers: +-------------------+ +----------------------+ +--------------+

  • Audio In ------>| Balanced Modulator|------->| Crystal Lattice or |------->| Mixer & |---> SSB
  • | (Diode Ring/IC) | DSB-SC | Mechanical Filter | SSB | Linear Power | Out
  • Carrier Osc --->| | | (SSB Passband) | | Amplifier |
  • +-------------------+ +----------------------+ +--------------+

Balanced Modulation: Audio ( 300 − 3000 Hz 300 - 3000\text{ Hz} 300 − 3000 Hz ) and an IF carrier (e.g., 9.0 MHz 9.0\text{ MHz} 9.0 MHz or 455 kHz 455\text{ kHz} 455 kHz ) feed a balanced modulator (diode ring or active Gilbert cell). The carrier is cancelled by balance, leaving a DSB-SC signal.

Sideband Selection: A crystal or mechanical bandpass filter passes the wanted sideband while rejecting the carrier region and opposite sideband. For example, 9.0003 9.0003 9.0003 to 9.0030 MHz 9.0030\text{ MHz} 9.0030 MHz passes 300 300 300 – 3000 Hz 3000\text{ Hz} 3000 Hz USB audio and is 2.7 kHz 2.7\text{ kHz} 2.7 kHz wide. Shape factor is commonly B W 60 dB / B W 6 dB BW_{60\text{dB}}/BW_{6\text{dB}} B W 60 dB ​ / B W 6 dB ​ : a low value such as 1.2 : 1 1.2:1 1.2 : 1 , close to unity, indicates steep skirts. Actual rejection follows the filter response.

Frequency Translation: The resulting low-level SSB signal at the IF is mixed with a local oscillator to translate it to the desired HF operating band, followed by linear (Class A and Class AB) power amplifiers. Non-linear amplifiers (such as Class C) cannot be used because they would destroy the envelope and recreate the missing sideband and carrier through intermodulation.

The Phasing Method

The phasing method eliminates the unwanted sideband through constructive and destructive phase cancellation: Audio I = Vm*cos(wm*t) ---> [Multiplier1] ---> v1 ---+

  • RF I = Vc*cos(wc*t) ------> [ ] |
  • +--> v1-v2: USB
  • Audio Q = Vm*sin(wm*t) ---> [Multiplier2] ---> v2 ---+ v1+v2: LSB
  • RF Q = Vc*sin(wc*t) ------> [ ]

The two audio inputs come from a quadrature audio network; the two RF inputs come from the same carrier oscillator with quadrature outputs. The combiner selects addition or subtraction as shown.

The audio signal is split into two components having an identical amplitude but a constant 90 ∘ 90^\circ 9 0 ∘ phase difference across the entire audio band ( I I I for In-phase, Q Q Q for Quadrature): v m 1 ( t ) = V m cos ⁡ ( ω m t ) , v m 2 ( t ) = V m sin ⁡ ( ω m t ) v_{m1}(t) = V_m \cos(\omega_m t), \quad v_{m2}(t) = V_m \sin(\omega_m t) v m 1 ​ ( t ) = V m ​ cos ( ω m ​ t ) , v m 2 ​ ( t ) = V m ​ sin ( ω m ​ t )

The RF carrier is split into two components in quadrature ( 90 ∘ 90^\circ 9 0 ∘ apart): v c 1 ( t ) = V c cos ⁡ ( ω c t ) , v c 2 ( t ) = V c sin ⁡ ( ω c t ) v_{c1}(t) = V_c \cos(\omega_c t), \quad v_{c2}(t) = V_c \sin(\omega_c t) v c 1 ​ ( t ) = V c ​ cos ( ω c ​ t ) , v c 2 ​ ( t ) = V c ​ sin ( ω c ​ t )

Modulator 1 output: v 1 ( t ) = v m 1 ( t ) ⋅ v c 1 ( t ) = V m V c cos ⁡ ( ω m t ) cos ⁡ ( ω c t ) = V m V c 2 [ cos ⁡ ( ( ω c − ω m ) t ) + cos ⁡ ( ( ω c + ω m ) t ) ] v_1(t) = v_{m1}(t) \cdot v_{c1}(t) = V_m V_c \cos(\omega_m t) \cos(\omega_c t) = \frac{V_m V_c}{2} [\cos((\omega_c - \omega_m)t) + \cos((\omega_c + \omega_m)t)] v 1 ​ ( t ) = v m 1 ​ ( t ) ⋅ v c 1 ​ ( t ) = V m ​ V c ​ cos ( ω m ​ t ) cos ( ω c ​ t ) = 2 V m ​ V c ​ ​ [ cos (( ω c ​ − ω m ​ ) t ) + cos (( ω c ​ + ω m ​ ) t )]

Modulator 2 output: v 2 ( t ) = v m 2 ( t ) ⋅ v c 2 ( t ) = V m V c sin ⁡ ( ω m t ) sin ⁡ ( ω c t ) = V m V c 2 [ cos ⁡ ( ( ω c − ω m ) t ) − cos ⁡ ( ( ω c + ω m ) t ) ] v_2(t) = v_{m2}(t) \cdot v_{c2}(t) = V_m V_c \sin(\omega_m t) \sin(\omega_c t) = \frac{V_m V_c}{2} [\cos((\omega_c - \omega_m)t) - \cos((\omega_c + \omega_m)t)] v 2 ​ ( t ) = v m 2 ​ ( t ) ⋅ v c 2 ​ ( t ) = V m ​ V c ​ sin ( ω m ​ t ) sin ( ω c ​ t ) = 2 V m ​ V c ​ ​ [ cos (( ω c ​ − ω m ​ ) t ) − cos (( ω c ​ + ω m ​ ) t )]

Subtracting v 2 ( t ) v_2(t) v 2 ​ ( t ) from v 1 ( t ) v_1(t) v 1 ​ ( t ) : v out ( t ) = v 1 ( t ) − v 2 ( t ) = V m V c cos ⁡ [ ( ω c + ω m ) t ] v_{\text{out}}(t) = v_1(t) - v_2(t) = V_m V_c \cos[(\omega_c + \omega_m)t] v out ​ ( t ) = v 1 ​ ( t ) − v 2 ​ ( t ) = V m ​ V c ​ cos [( ω c ​ + ω m ​ ) t ]

The lower sideband is completely cancelled ( 180 ∘ 180^\circ 18 0 ∘ anti-phase), yielding pure Upper Sideband (USB). Summing the two outputs instead yields Lower Sideband (LSB).

Modern Digital Implementation: A digital Hilbert transformer forms quadrature audio components for the same cancellation process. Accurate phase and amplitude balance improves unwanted-sideband rejection. Finite filters and any analogue I/Q paths still affect the result; carrier leakage requires separate balance or offset correction. Arithmetic word length alone does not specify RF carrier or sideband suppression.

  • 8. Demodulation of AM and SSB Signals
  • AM Demodulation: The Diode Envelope Detector

Full-carrier AM possesses a visible carrier envelope that can be demodulated using an inexpensive passive diode envelope detector : RF In -----[ >| ]------+-------+-------> Audio Out

  • Diode | |
  • [R] [C]
  • | |
  • GND GND

Rectification: The semiconductor diode conducts only on positive half-cycles of the RF waveform, stripping the negative envelope.

Filtering: The parallel resistor-capacitor ( R C RC RC ) low-pass filter smooths out the high-frequency RF carrier ripple while allowing the audio-frequency variations of the envelope to pass unimpeded.

Time Constant Selection: The R C RC RC time constant ( τ = R C \tau = RC τ = RC ) must be carefully engineered: 1 f c ≪ R C ≪ 1 f m , max \frac{1}{f_c} \ll RC \ll \frac{1}{f_{m,\text{max}}} f c ​ 1 ​ ≪ RC ≪ f m , max ​ 1 ​

If R C RC RC is too small , the capacitor discharges too quickly between RF cycles, leaving significant RF carrier ripple on the audio line.

If R C RC RC is too large , the capacitor cannot discharge rapidly enough to track steep downward excursions of the audio signal. The diode is reverse-biased and cut off, resulting in diagonal clipping distortion.

SSB Demodulation: The Product Detector

Because an SSB signal lacks a carrier wave, its envelope does not mirror the original audio modulating waveform. Passing an SSB signal through a diode envelope detector produces only garbled, distorted, and completely unintelligible noise.

To recover the original audio, the missing carrier must be artificially regenerated and mixed with the incoming SSB signal inside a Product Detector (which is fundamentally a balanced mixer): Received SSB Signal (fc + fm) --->| Product |----[ Low-Pass ]----> Demodulated

  • | Detector | Filter Audio (fm)
  • Local BFO / CIO (fc) ------------>| (Mixer) |

Carrier Insertion: A highly stable local oscillator—termed the Beat Frequency Oscillator (BFO) or Carrier Insertion Oscillator (CIO) —generates an unmodulated CW signal at the precise frequency of the original suppressed carrier ( f c f_c f c ​ ).

Multiplication (Mixing): The incoming USB signal at f c + f m f_c + f_m f c ​ + f m ​ is multiplied with the BFO carrier at f c f_c f c ​ in the product detector: v out ( t ) = [ V s cos ⁡ ( 2 π ( f c + f m ) t ) ] ⋅ [ V b cos ⁡ ( 2 π f c t ) ] v_{\text{out}}(t) = [V_s \cos(2\pi (f_c + f_m)t)] \cdot [V_b \cos(2\pi f_c t)] v out ​ ( t ) = [ V s ​ cos ( 2 π ( f c ​ + f m ​ ) t )] ⋅ [ V b ​ cos ( 2 π f c ​ t )] v out ( t ) = V s V b 2 [ cos ⁡ ( 2 π ( 2 f c + f m ) t ) + cos ⁡ ( 2 π f m t ) ] v_{\text{out}}(t) = \frac{V_s V_b}{2} [\cos(2\pi (2f_c + f_m)t) + \cos(2\pi f_m t)] v out ​ ( t ) = 2 V s ​ V b ​ ​ [ cos ( 2 π ( 2 f c ​ + f m ​ ) t ) + cos ( 2 π f m ​ t )]

Low-Pass Filtering: The sum component at double the carrier frequency ( 2 f c + f m 2f_c + f_m 2 f c ​ + f m ​ ) is discarded by a simple audio low-pass filter, leaving the pure difference term: the original baseband audio frequency f m f_m f m ​ .

Frequency and Phase Accuracy: The BFO must match the original carrier frequency within ± 20 Hz \pm 20\text{ Hz} ± 20 Hz to ± 50 Hz \pm 50\text{ Hz} ± 50 Hz . A tuning error of 100 Hz 100\text{ Hz} 100 Hz makes human voices sound unnatural ("Donald Duck" pitch elevation if BFO is low, or deep bass growl if BFO is high), and an error exceeding 200 Hz 200\text{ Hz} 200 Hz impairs intelligibility.

9. Comprehensive Comparison: AM, DSB-SC, and SSB

Feature Double Sideband Full Carrier (AM) Double Sideband Suppressed Carrier (DSB-SC) Single Sideband Suppressed Carrier (SSB)

Carrier Present? Yes ( 66.7 % 66.7\% 66.7% of total power at m = 1 m=1 m = 1 ) No (Suppressed > 40 dB >40\text{ dB} > 40 dB ) No (Suppressed > 40 − 50 dB >40-50\text{ dB} > 40 − 50 dB )

Number of Sidebands Two (USB + LSB) Two (USB + LSB) One (USB or LSB)

Occupied Bandwidth 2 f m , max 2f_{m,\text{max}} 2 f m , max ​ ( 6.0 kHz 6.0\text{ kHz} 6.0 kHz ) 2 f m , max 2f_{m,\text{max}} 2 f m , max ​ ( 6.0 kHz 6.0\text{ kHz} 6.0 kHz ) f m , max − f m , min f_{m,\text{max}}-f_{m,\text{min}} f m , max ​ − f m , min ​ ( 2.7 kHz 2.7\text{ kHz} 2.7 kHz for 300–3000 Hz audio)

Power in Information at 100% Modulation 33.3 % 33.3\% 33.3% total ( 16.7 % 16.7\% 16.7% per sideband) 100 % 100\% 100% ( 50 % 50\% 50% per sideband) 100 % 100\% 100% (in single sideband)

DC-to-RF Efficiency Depends on PA and modulation method Depends on PA Depends on PA; linear envelope amplification required

Receiver Noise Bandwidth Approximately 6 kHz 6\text{ kHz} 6 kHz for this example Approximately 6 kHz 6\text{ kHz} 6 kHz Follows the selected speech passband; narrower filters admit less white noise

Demodulator Circuitry Simple diode envelope detector Product detector (requires BFO) Product detector (requires BFO)

Tuning Criticality Non-critical Moderate Highly critical (within ± 20 − 50 Hz \pm 20-50\text{ Hz} ± 20 − 50 Hz )

Amateur Applications Vintage AM nets, aeronautical Rarely used alone Primary HF voice mode, weak-signal VHF/UHF