Study guide

11.2 The Ionosphere, Solar Radiation, and Solar Cycles

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

11.2 The Ionosphere, Solar Radiation, and Solar Cycles

Key Takeaways Explain This Topic AI

The ionosphere is formed when solar extreme ultraviolet (EUV) and soft X-ray radiation photoionise neutral atmospheric gases (oxygen and nitrogen) between altitudes of 60 km 60\text{ km} 60 km and 500 km 500\text{ km} 500 km , liberating free electrons.

The D-layer ( 60 to 90 km 60\text{ to }90\text{ km} 60 to 90 km ) features high atmospheric density and high electron-neutral collision frequency, converting MF and lower HF wave energy into heat; it functions as a daytime absorption blanket that vanishes rapidly after sunset.

The F-layer ( 140 to 500 km 140\text{ to }500\text{ km} 140 to 500 km ) sustains the highest electron density and acts as the primary reflector for worldwide long-distance HF communications; it splits into F1 and F2 layers during daylight and recombines into a single persistent F-layer at night.

Solar magnetic activity follows an approximate 11-year cycle (the Schwabe cycle), driven by the solar dynamo and differential rotation, which governs sunspot numbers and total ionizing radiation.

The 10.7 cm 10.7\text{ cm} 10.7 cm Solar Flux Index measures solar spectral flux density near 2800 MHz 2800\text{ MHz} 2800 MHz and is a useful ground-based proxy for solar activity and EUV output. Greater activity generally favours higher F2-supported frequencies, but SFI alone does not determine whether a particular HF band is open.

Last updated: November 2026

11.2 The Ionosphere, Solar Radiation, and Solar Cycles

Long-distance, intercontinental High Frequency (HF) communication without artificial satellites or undersea cables is made possible by the ionosphere —a dynamic shell of partially ionised plasma enveloping the Earth between altitudes of approximately 60 km 60\text{ km} 60 km and 500 km 500\text{ km} 500 km . Operating as a vast, solar-powered radio reflector, the ionosphere refracts HF electromagnetic waves back to the Earth's surface. Understanding the photoionisation mechanisms that create this plasma, the unique diurnal behavior of its discrete layers, and the periodic solar cycles that govern its density is fundamental to mastering HF radio propagation.

Formation of the Ionosphere: Photoionisation Mechanics

The upper atmosphere consists of neutral gas molecules and atoms, primarily molecular nitrogen ( N 2 N_2 N 2 ​ ), molecular oxygen ( O 2 O_2 O 2 ​ ), atomic oxygen ( O O O ), and nitric oxide ( N O NO NO ). The ionosphere is created through photoionisation , driven by solar electromagnetic radiation in the Extreme Ultraviolet (EUV) spectrum (wavelengths λ ≈ 10 to 121 nm \lambda \approx 10\text{ to }121\text{ nm} λ ≈ 10 to 121 nm ) and soft/hard X-ray spectrum ( λ < 10 nm \lambda < 10\text{ nm} λ < 10 nm ).

When a high-energy solar photon strikes a neutral gas atom or molecule, it transfers its quantum energy ( E = h ν E = h\nu E = h ν ). If this photon energy exceeds the first ionisation threshold of the atom (typically 12 to 15 eV 12\text{ to }15\text{ eV} 12 to 15 eV ), it ejects a bound orbital valence electron, creating a free electron and a positively charged ion: O + h ν → O + + e − O + h\nu \to O^+ + e^- O + h ν → O + + e − N 2 + h ν → N 2 + + e − N_2 + h\nu \to N_2^+ + e^- N 2 ​ + h ν → N 2 + ​ + e − O 2 + h ν → O 2 + + e − O_2 + h\nu \to O_2^+ + e^- O 2 ​ + h ν → O 2 + ​ + e − N O + h ν → N O + + e − NO + h\nu \to NO^+ + e^- NO + h ν → N O + + e − Photoionisation production profile

  • High altitude: Strong sunlight, few neutral particles
  • > relatively few ion pairs produced
  • Intermediate altitude: Enough photons and neutral particles
  • > a maximum in production rate q(z)
  • Lower altitude: Much ionising radiation absorbed above
  • > reduced photoionisation production

q(z) is ion pairs produced per cubic metre per second.

Electron density Ne is a concentration, not a production rate.

Its profile also depends on electron loss and plasma transport.

The Chapman Ionisation Profile

Chapman's model explains how competition between decreasing neutral density and absorption of incoming solar radiation produces an altitude of maximum photoionisation rate . Electron density is not the same quantity: it depends on production, chemical loss and plasma transport.

High Altitudes: Ionising radiation is plentiful, but few neutral particles are available to absorb it, limiting production per unit volume.

Lower Altitudes: The dense overlying atmosphere absorbs much of the ionising radiation, reducing photoionisation. This is a gradual, wavelength-dependent effect, not a universal zero-ionisation boundary at 60 km 60\text{ km} 60 km .

Intermediate Altitudes: Sufficient photons and neutral particles coexist to produce peaks in ionisation. Different absorption and loss processes contribute to the D, E and F regions.

The Stratified Ionospheric Layers: D, E, F1, and F2

Atmospheric composition changes with altitude, different gases absorb different solar wavelengths, and the rates of electron loss also change. Together with plasma transport, these processes produce the D, E, F1 and F2 structure. The regions are not formed by gravitational separation alone, and their heights and densities vary with time and location. Diurnal Ionospheric Structure and Electron Density Profile

  • Altitude (km)
  • ^
  • 500 | DAYTIME NIGHTTIME
  • |
  • 400 | /-------\
  • | / F2 \ (210-450 km) /-------\
  • 300 | | | / F \ (250-350 km)
  • | | F1 | (140-210 km) | Merged |
  • 200 | \---------/ \---------/
  • | |
  • 100 | /-------\ E (90-140 km) : (Residual E)
  • | |=========| D (60-90 km) (Absorber) : (D vanishes)
  • 0 +----------+---------+------------------------------+--------->
  • 10^8 10^11 10^12 10^8 10^11
  • Electron Density N_e (electrons / m^3)
  • 1. The D-Layer ( 60 to 90 km 60\text{ to }90\text{ km} 60 to 90 km )

Ionisation Sources: Hard X-rays ( λ < 1 nm \lambda < 1\text{ nm} λ < 1 nm ) during solar flares and solar Lyman-alpha radiation ( λ = 121.6 nm \lambda = 121.6\text{ nm} λ = 121.6 nm ) ionising trace amounts of nitric oxide ( N O NO NO ), along with high-energy galactic cosmic rays.

Electron Density ( N e N_e N e ​ ): Modest daytime density, typically 10 8 to 10 9 electrons/m 3 10^8\text{ to }10^9\text{ electrons/m}^3 1 0 8 to 1 0 9 electrons/m 3 at solar noon.

Atmospheric Environment: The D-region lies relatively low in the atmosphere, where neutral particles are abundant. Electrons therefore undergo frequent collisions with neutral molecules, much more readily than in the higher F-region.

RF Attenuation Mechanism (The Absorption Blanket): When an electromagnetic wave passes through the D-layer, its alternating electric field imparts kinetic energy to the free electrons, causing them to oscillate. Before these vibrating electrons can reradiate their energy, they collide with neutral gas molecules. The electron's kinetic energy is converted into thermal heat in the neutral gas. This process is known as non-deviative absorption .

A simplified collisional model gives the absorption dependence α D ∝ N e ν ν 2 + ω 2 . \alpha_D\propto\frac{N_e\nu}{\nu^2+\omega^2}. α D ​ ∝ ν 2 + ω 2 N e ​ ν ​ .

When ω = 2 π f ≫ ν \omega=2\pi f\gg\nu ω = 2 π f ≫ ν , this approaches α D ∝ N e ν / f 2 \alpha_D\propto N_e\nu/f^2 α D ​ ∝ N e ​ ν / f 2 . Here ν \nu ν is the electron-neutral collision rate. This explains the usual trend toward greater D-region absorption at lower HF frequencies; it is not a fixed loss value for each band.

Important

Operational Effect: Daytime absorption restricts MF and lower HF skywave more strongly than higher HF. Nevertheless, 80 m 80\text{ m} 80 m can support daytime regional skywave when it lies above the circuit's LUF and below its ionospheric upper limit. Solar flares can increase absorption even on high HF bands. Path length through the D-region, solar conditions and frequency all matter.

After Sunset: Electron loss rapidly weakens the normal D-region absorption, allowing lower frequencies to reach the higher refracting regions more readily. This improves many nighttime MF/HF paths, but does not by itself guarantee a received signal or a fixed recovery time.

2. The E-Layer ( 90 to 140 km 90\text{ to }140\text{ km} 90 to 140 km )

Ionisation Sources: Soft X-rays ( 1 to 10 nm 1\text{ to }10\text{ nm} 1 to 10 nm ) and solar EUV radiation ( 80 to 103 nm 80\text{ to }103\text{ nm} 80 to 103 nm ) ionising molecular oxygen ( O 2 O_2 O 2 ​ ).

Electron Density ( N e N_e N e ​ ): Moderate density, peaking around 10 11 electrons/m 3 10^{11}\text{ electrons/m}^3 1 0 11 electrons/m 3 at solar noon.

Operational Role: Atmospheric density at 110 km 110\text{ km} 110 km is sufficiently low that collision frequency drops significantly. The E-layer can refract signals in the 2 to 7 MHz 2\text{ to }7\text{ MHz} 2 to 7 MHz range back to Earth over single-hop distances of 1000 to 2000 km 1000\text{ to }2000\text{ km} 1000 to 2000 km .

Diurnal Behavior: Recombination proceeds rapidly after dusk, though a very weak residual E-layer persists through the night ( N e ≈ 10 9 m − 3 N_e \approx 10^9\text{ m}^{-3} N e ​ ≈ 1 0 9 m − 3 ).

Sporadic-E ( E s E_s E s ​ ): During summer months, intense, localized clouds of metallic ions (meteoric ablation deposits of Fe + , Mg + , Si + \text{Fe}^+, \text{Mg}^+, \text{Si}^+ Fe + , Mg + , Si + ) are compressed into ultra-dense, paper-thin sheets ( 1 to 2 km 1\text{ to }2\text{ km} 1 to 2 km thick) by upper-atmospheric wind shears. These Sporadic-E clouds can achieve plasma frequencies exceeding 15 to 30 MHz 15\text{ to }30\text{ MHz} 15 to 30 MHz , permitting spectacular multi-hop skip openings on the 28 MHz 28\text{ MHz} 28 MHz , 50 MHz 50\text{ MHz} 50 MHz , and occasionally 144 MHz 144\text{ MHz} 144 MHz amateur bands.

3. The F-Layer ( 140 to 500 km 140\text{ to }500\text{ km} 140 to 500 km )

Ionisation Sources: Solar EUV photons ionise the upper atmosphere, including atomic oxygen. Production depends on the solar spectrum, the relevant absorption/ionisation cross-sections and the local neutral composition; it is not specified by one solar emission line alone.

Atmospheric Environment: At altitudes above 200 km 200\text{ km} 200 km , atmospheric pressure is negligible. Free electron collision frequency is exceedingly low ( ν ≪ 10 3 s − 1 \nu \ll 10^3\text{ s}^{-1} ν ≪ 1 0 3 s − 1 ), rendering the F-layer a virtually lossless refractive medium for RF waves.

Daytime Splitting (F1 and F2): Under the influence of intense solar overhead illumination, the F-region divides into two distinct zones:

F1-Layer ( 140 to 210 km 140\text{ to }210\text{ km} 140 to 210 km ): Daytime peak electron density reaches 2 to 5 × 10 11 m − 3 2\text{ to }5 \times 10^{11}\text{ m}^{-3} 2 to 5 × 1 0 11 m − 3 . It acts as an intermediate refracting layer for lower HF signals, causing distinct cusps on vertical ionograms. The F1-layer recombines rapidly after sunset and merges into the composite night F-layer.

F2-Layer ( 210 to 450 km 210\text{ to }450\text{ km} 210 to 450 km ): The highest, thickest, and most heavily ionised layer of the Earth's atmosphere. Peak electron density reaches 10 12 to 3 × 10 12 electrons/m 3 10^{12}\text{ to }3 \times 10^{12}\text{ electrons/m}^3 1 0 12 to 3 × 1 0 12 electrons/m 3 during solar maximum. The F2-layer is the primary reflector for all intercontinental amateur DX communications on HF.

Nighttime Electron Loss: Direct radiative recombination of O + O^+ O + is slow. Important loss paths first convert atomic ions to molecular ions through reactions with N 2 N_2 N 2 ​ or O 2 O_2 O 2 ​ , followed by faster dissociative recombination with electrons. One example is O + + N 2 → N O + + N O^++N_2\to NO^++N O + + N 2 ​ → N O + + N , followed by N O + + e − → N + O NO^++e^-\to N+O N O + + e − → N + O . Because molecular neutral densities are low in the F2-region, overall electron loss is relatively slow. Plasma transport also helps determine the nighttime density.

Tip

The Unified Night F-Layer: Because electron loss at 300 km 300\text{ km} 300 km is extraordinarily slow, the F2-layer persists throughout the entire night . As dusk falls, the F1-layer recombines and merges with the base of the F2-layer, forming a single combined F-layer situated at an altitude of approximately 250 to 350 km 250\text{ to }350\text{ km} 250 to 350 km that supports long-distance HF DX around the clock.

Comprehensive Ionospheric Layer Matrix

Layer Daytime Altitude Nighttime State Peak Electron Density ( N e N_e N e ​ , m − 3 \text{m}^{-3} m − 3 ) Dominant Solar Radiation Propagation Impact on Amateur Bands

D About 60 60 60 – 90 km 90\text{ km} 90 km Normally insignificant to HF skywave at night Typically low compared with E/F Lyman- α \alpha α and X-rays; other ionisation sources also contribute Absorbs MF/lower HF most strongly by day; solar flares can increase absorption throughout HF

E 90 − 140 km 90 - 140\text{ km} 90 − 140 km Weak residual layer ( 10 9 m − 3 10^9\text{ m}^{-3} 1 0 9 m − 3 ) 10 11 10^{11} 1 0 11 Soft X-rays ( 1 − 10 nm 1-10\text{ nm} 1 − 10 nm ), EUV ( 80 − 103 nm 80-103\text{ nm} 80 − 103 nm ) Daytime skip ( 1000 − 2000 km 1000 - 2000\text{ km} 1000 − 2000 km ) on 3.5 − 14 MHz 3.5 - 14\text{ MHz} 3.5 − 14 MHz ; site of Sporadic-E ( E s E_s E s ​ )

F1 140 − 210 km 140 - 210\text{ km} 140 − 210 km Merges into night F-layer 2 − 5 × 10 11 2 - 5 \times 10^{11} 2 − 5 × 1 0 11 Solar EUV ( 10 − 80 nm 10-80\text{ nm} 10 − 80 nm ) Daytime inflection; minor absorption/bending; disappears at dusk

F2 About 210 210 210 – 450 km 450\text{ km} 450 km Persists as the main night F-region Can reach 10 12 10^{12} 1 0 12 – 3 × 10 12 m − 3 3\times10^{12}\text{ m}^{-3} 3 × 1 0 12 m − 3 at high solar activity Solar EUV acting on upper-atmospheric gases Main long-distance HF refracting region; typical single-hop limit about 4000 km 4000\text{ km} 4000 km

Solar Activity, Sunspots, and the 11-Year Schwabe Cycle

The electron density of the ionosphere is not static; it is directly coupled to the magnetic dynamism of the Sun. Solar activity undergoes a well-documented cyclic variation discovered in 1843 by Heinrich Schwabe: the 11-year solar cycle . Approximate cycle timing (schematic, not measured data)

  • Phase Minimum Maximum Minimum Maximum Minimum
  • Elapsed years 0 5-6 11 16-17 22
  • Relative activity Low High Low High Low

A cycle runs from one minimum to the next, averaging about 11 years.

Peak strength and exact timing vary. SSN and SFI are different

indices and do not share a single numerical scale.

The Solar Dynamo and Sunspot Formation

The Sun does not rotate as a rigid body. Because it is a ball of incandescent gas and plasma, its equator rotates once every 25 days 25\text{ days} 25 days , while its polar regions rotate once every 35 days 35\text{ days} 35 days . This differential rotation twists and stretches the Sun's internal poloidal magnetic field lines into concentrated east-west toroidal magnetic ropes wrapped tightly beneath the solar surface.

When magnetic tension becomes extreme, buoyant magnetic flux tubes ( 0.1 to 0.4 Tesla 0.1\text{ to }0.4\text{ Tesla} 0.1 to 0.4 Tesla ) erupt through the visible solar surface (the photosphere). The intense magnetic fields choke off the upward convective transport of superheated plasma from the solar interior. Consequently, the surface within the magnetic footpoints cools from its normal temperature of ≈ 5800 K \approx 5800\text{ K} ≈ 5800 K down to ≈ 3500 − 4000 K \approx 3500 - 4000\text{ K} ≈ 3500 − 4000 K . Because the cooler area emits significantly less optical light than the surrounding photosphere, it appears visually dark by contrast—forming a sunspot .

Crucially for radio propagation, sunspots themselves are not the source of ionizing radiation. Rather, the intensely active magnetic areas immediately surrounding sunspots—termed plages and faculae —emit colossal torrents of ionizing extreme ultraviolet (EUV) and X-ray radiation.

Sunspot Quantification: The International Sunspot Number ( R i R_i R i ​ )

To quantify solar activity over historical epochs, Swiss astronomer Rudolf Wolf formulated the standard Sunspot Number ( R i R_i R i ​ , or Wolf Number): R i = k ( 10 g + s ) R_i = k(10g + s) R i ​ = k ( 10 g + s )

where:

g g g is the number of identified sunspot groups.

s s s is the total count of individual visible spots across all groups.

k k k is an observatory scaling factor that standardizes observations across varying telescope apertures and atmospheric viewing conditions.

Daily sunspot numbers vary with solar rotation and the evolution of active regions. The standard smoothed monthly sunspot number uses a centred 13 13 13 -month window: the two end months receive half weight, the other eleven receive full weight, and the sum is divided by 12 12 12 . This suppresses short-term fluctuations and shows the underlying cycle trend.

The 22-Year Hale Magnetic Cycle

Every 11 years, at the peak of each solar cycle, the Sun's global magnetic dipole completely reverses polarity: magnetic north becomes magnetic south. It requires two full 11-year Schwabe cycles—a 22-year Hale Cycle —for the Sun's global magnetic field to return to its original orientation.

The Solar Flux Index (SFI) and HF Band Openings

Visual sunspot counts provide a long historical record. The Solar Flux Index supplies an independent, instrumentally measured indicator of solar activity that can be used as a proxy for ionising solar output; it does not directly measure EUV irradiance.

What Does the Solar Flux Index Measure?

The Solar Flux Index is the Sun’s spectral flux density at 10.7 cm 10.7\text{ cm} 10.7 cm , approximately 2800 MHz 2800\text{ MHz} 2800 MHz . The Canadian monitoring programme measures it at the Dominion Radio Astrophysical Observatory near Penticton, British Columbia. Precise daily determinations include the local-noon measurement.

SFI is expressed in Solar Flux Units (SFU) : 1 SFU = 10 − 22 W ⋅ m − 2 ⋅ Hz − 1 1\text{ SFU} = 10^{-22}\text{ W}\cdot\text{m}^{-2}\cdot\text{Hz}^{-1} 1 SFU = 1 0 − 22 W ⋅ m − 2 ⋅ Hz − 1

Why SFI is the Primary Propagation Metric

Ground Measurability: Solar extreme ultraviolet (EUV) radiation—the direct driver of F2-layer photoionisation—is entirely absorbed by the upper atmosphere. Consequently, direct EUV monitoring requires orbital satellites. In contrast, 10.7 cm 10.7\text{ cm} 10.7 cm ( 2800 MHz 2800\text{ MHz} 2800 MHz ) microwave emissions penetrate cleanly through Earth's atmosphere, enabling continuous, highly reliable ground-based monitoring regardless of terrestrial weather.

Activity Proxy: The 2800 MHz 2800\text{ MHz} 2800 MHz emission originates in the solar atmosphere and correlates with active-region magnetic activity and EUV output. This makes SFI useful in ionospheric modelling. It is a proxy rather than an exact measurement of EUV, and local HF conditions also depend on season, time, path and geomagnetic activity.

Solar Cycle Metrics and Amateur HF Band Conditions

Solar activity General HF propagation trend

Near solar minimum Lower F2 electron densities usually restrict the highest supported frequencies. High HF bands have fewer F2 openings; lower bands remain important, especially at night.

Increasing activity Higher F2-supported frequencies become more frequent, expanding the choice of HF bands on suitable paths.

Near solar maximum Long-distance openings on 21 21 21 , 24 24 24 and 28 MHz 28\text{ MHz} 28 MHz become more frequent; strong F2 conditions can sometimes support 50 MHz 50\text{ MHz} 50 MHz . Flares and geomagnetic disturbances can also disrupt communications.

These are trends, not a schedule or fixed SFI threshold. Check the intended path and time: no solar-cycle category guarantees 14 MHz 14\text{ MHz} 14 MHz around the clock or zero absorption on 28 MHz 28\text{ MHz} 28 MHz . Suitable high-HF openings can nevertheless give strong intercontinental signals with ordinary amateur power and antennas.