Study guide
3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers
ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: DC Theory, Circuit Laws & Passive Components
1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants
2 Chapter 2: Impedance, Resonance & Passive Filters
2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads
3 Chapter 3: Semiconductor Devices & Power Supplies
3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators
4 Chapter 4: Oscillators & Frequency Synthesis
4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies
5 Chapter 5: RF Amplifiers & Linearity
5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion
6 Chapter 6: Modulation & Demodulation
6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols
7 Chapter 7: Transmitters, Mixers & Receivers
7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity
8 Chapter 8: Transmission Lines & Waveguides
8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs
9 Chapter 9: Impedance Matching & Baluns
9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice
10 Chapter 10: Practical Antennas & Arrays
10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns
11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics
11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths
12 Chapter 12: VHF/UHF Propagation & Space Communications
12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)
13 Chapter 13: Test Equipment & RF Measurements
13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters
14 Chapter 14: Advanced RF Analysis & Diagnostics
14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing
15 Chapter 15: Electromagnetic Compatibility & Interference
15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques
16 Chapter 16: Electrical, RF & Station Safety
16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection
3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers
Key Takeaways Explain This Topic AI
Thermionic valves emit electrons from a heated cathode into a high vacuum via the Edison effect; directly heated filaments heat rapidly but require hum-balancing, while indirectly heated cathodes isolate AC heaters.
Triodes exhibit internal anode-to-grid capacitance (C_ag) that causes positive feedback and self-oscillation via the Miller effect, requiring neutralisation in grid-driven RF amplifiers.
Tetrodes introduce a screen grid to slash C_ag, but suffer from secondary electron emission dynatron kinks; pentodes add a suppressor grid tied to the cathode to eliminate this kink.
Grounded-grid triode stages usually need no neutralisation at HF. They have low input impedance, use an input matching network for 50-ohm exciters, and deliver feed-through drive power as part of their RF output.
Valve plate supplies and charged filter capacitors can be lethal after mains power is removed. E=CV²/2 calculates stored energy; bleeders and interlocks reduce risk but qualified servicing still requires isolation, rated discharge and independent voltage verification.
Last updated: November 2026
3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers
Key Focus: Thermionic valves (vacuum tubes) remain prominent in high-power amateur radio linear amplifiers operating at power levels up to the Australian legal limit ( 400 W 400\text{ W} 400 W PEP for Advanced licensees). Understanding valve physics, inter-electrode capacitances, neutralisation, grounded-grid circuitry, and high-voltage safety is critical for the Advanced Theory syllabus.
Principles of Thermionic Emission
Thermionic emission, originally termed the Edison effect , occurs when thermal energy imparts sufficient kinetic energy to electrons within a metallic conductor to overcome the surface potential barrier—the material's work function ( Φ \Phi Φ ). Free electrons boil off the hot conductor surface into the surrounding evacuated envelope. +-------------------------------------------------------------+
- | ANODE / PLATE |
- | (High Positive Potential) |
- +-------------------------------------------------------------+
- ^ ^ ^ ^ ^
- | | | | | Accelerating
- e- e- e- e- e- Electric Field
- | | | | |
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . Negative Space Charge Cloud . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
- +-------------------------------------------------------------+
- | HEATED CATHODE |
- +-------------------------------------------------------------+
- [ Heater Filament: Electrical or AC Heating ]
- Cathode Construction
Directly Heated Filaments: The filament wire itself serves as the electron-emitting cathode. Made from thoriated tungsten (tungsten alloyed with 1 % 1\% 1% to 2 % 2\% 2% thorium oxide), these operate at incandescent temperatures (typically about 1900 K 1900\text{ K} 1900 K , or 1630 ∘ C 1630^\circ\text{C} 163 0 ∘ C ). They are exceptionally rugged, withstand bombardment by residual gas ions under extreme plate potentials ( > 3000 V > 3000\text{ V} > 3000 V ), and warm up in seconds. Used in classic transmitting tubes such as the 3-500Z , 811A , and 572B . However, because AC filament current flows through the emitter, a center-tapped filament transformer with RF bypass capacitors is mandatory to avoid 50 Hz 50\text{ Hz} 50 Hz audio hum modulation.
Indirectly Heated Cathodes: An oxide-coated nickel sleeve (coated with barium and strontium oxides) surrounds an electrically insulated tungsten heater wire. Operating at lower temperatures ( 750 ∘ C 750^\circ\text{C} 75 0 ∘ C to 800 ∘ C 800^\circ\text{C} 80 0 ∘ C ), these provide high emission efficiency. The emitting sleeve is electrically isolated from the AC filament voltage, preventing mains hum injection. Used in tubes such as the 6146B and 4CX250B . Follow the manufacturer’s heater warm-up and voltage-sequencing instructions before applying operating voltages. For the 4CX250B, rated heater voltage must be applied for at least 30 seconds 30\text{ seconds} 30 seconds first.
The Anode (Plate) and Space Charge
The anode (or plate ) surrounds the cathode and is maintained at a high positive potential ( 600 V 600\text{ V} 600 V to 3500 V 3500\text{ V} 3500 V DC). Emitted electrons form a negative cloud around the cathode known as the space charge . At low plate voltages, this space charge repels newly emitted electrons back into the cathode. Current obeys the Child-Langmuir three-halves power law ( I a = k V a 3 / 2 I_a = k V_a^{3/2} I a = k V a 3/2 ) until the plate voltage is high enough to attract all emitted electrons, reaching emission saturation .
- Evolution of Valve Architectures DIODE TRIODE TETRODE PENTODE
- ===== Plate ===== Plate ===== Plate ===== Plate
- - - Suppressor (G3)
- - - Screen (G2) - - - Screen (G2)
- - - Grid (G1) - - - Control (G1) - - - Control (G1)
- ---- Cathode ----- Cathode ----- Cathode ----- Cathode
- 1. The Triode Valve
Invented by Lee de Forest, the triode inserts an electrostatic wire mesh—the control grid ( G 1 G_1 G 1 )—between the cathode and the anode. Because the control grid is positioned physically close to the cathode, a small variation in grid voltage has a far greater influence on the electric field at the cathode surface than a large variation in anode voltage.
Valve Parameters
Amplification Factor ( μ \mu μ ): The relative effectiveness of the control grid compared to the plate in controlling plate current: μ = ∣ Δ V a Δ V g ∣ I a = constant \mu = \left| \frac{\Delta V_a}{\Delta V_g} \right|_{I_a = \text{constant}} μ = Δ V g Δ V a I a = constant
Dynamic Anode Resistance ( r a r_a r a ): The internal AC resistance of the plate: r a = Δ V a Δ I a ∣ V g = constant r_a = \left. \frac{\Delta V_a}{\Delta I_a} \right|_{V_g = \text{constant}} r a = Δ I a Δ V a V g = constant
Mutual Conductance (Transconductance, g m g_m g m ): The change in plate current produced by a change in grid voltage: g m = Δ I a Δ V g ∣ V a = constant g_m = \left. \frac{\Delta I_a}{\Delta V_g} \right|_{V_a = \text{constant}} g m = Δ V g Δ I a V a = constant
- Universal Relationship: μ = g m × r a \mu = g_m \times r_a μ = g m × r a
- Grid Bias and the Miller Effect
Grid-to-cathode DC bias sets the quiescent operating point; RF drive adds an alternating voltage. In Class AB1, the grid remains non-positive and draws negligible current. In Class AB2, positive grid excursions draw grid current, requiring driver power and observance of grid-dissipation limits. Suitable high-mu triodes can use zero DC bias.
However, the physical proximity of the plate and control grid creates a significant internal inter-electrode capacitance: the anode-to-grid capacitance ( C a g C_{ag} C a g , typically 2 pF 2\text{ pF} 2 pF to 10 pF 10\text{ pF} 10 pF ). In a grid-driven amplifier, this capacitance multiplies at the input via the Miller effect : C in = C g k + C a g ( 1 + ∣ A v ∣ ) C_{\text{in}} = C_{gk} + C_{ag}(1 + |A_v|) C in = C g k + C a g ( 1 + ∣ A v ∣ )
More critically, at radio frequencies, C a g C_{ag} C a g feeds amplified RF energy from the plate circuit back to the grid. In a tuned RF amplifier, the inductive component of the plate tank load below resonance shifts the phase of the feedback signal by 180 ∘ 180^\circ 18 0 ∘ , converting the amplifier into a Tuned-Plate Tuned-Grid (TPTG) self-oscillator . To prevent destructive oscillation, triode grid-driven amplifiers require neutralisation —feeding an equal-amplitude, opposite-phase ( 180 ∘ 180^\circ 18 0 ∘ ) RF signal back to the grid via an external neutralizing capacitor ( C n C_n C n ) to cancel the internal feedback.
2. The Tetrode Valve
To reduce anode-to-grid feedback and the Miller effect, the tetrode introduces a second grid: the screen grid ( G 2 G_2 G 2 ), placed between the control grid and the plate:
The screen grid is biased at a positive DC potential (typically 250 V 250\text{ V} 250 V to 400 V 400\text{ V} 400 V ) and bypassed to ground for RF using a low-inductance capacitor.
The screen grid acts as an electrostatic Faraday shield , reducing the plate-to-control-grid capacitance ( C a g C_{ag} C a g ) from several picofarads down to less than 0.05 pF 0.05\text{ pF} 0.05 pF . This often avoids neutralisation at HF; residual feedback and common lead inductance can still require neutralisation, especially at higher frequencies.
The Secondary Emission Flaw (Dynatron Kink)
High-velocity primary electrons striking the plate dislodge electrons from the plate metal in a process called secondary emission . In a triode, these secondary electrons are immediately pulled back to the highly positive plate. In a tetrode, however, when the plate voltage swings below the screen grid voltage during large signal excursions, the positive screen grid attracts these secondary electrons away from the plate.
As a result, an increase in plate voltage produces a decrease in net plate current. This generates a region of negative dynamic resistance known as the dynatron kink , causing severe audio/RF distortion and triggering destructive parasitic oscillations.
3. The Pentode Valve and Beam Power Tetrode
The pentode introduces a third grid: the suppressor grid ( G 3 G_3 G 3 ), placed between the screen grid and the plate:
The suppressor grid is a coarse mesh connected directly to the cathode or ground ( 0 V 0\text{ V} 0 V ). It has minimal effect on high-velocity primary electrons heading toward the plate.
However, it forms a negative electrostatic potential barrier that repels low-velocity secondary electrons back into the plate, completely eliminating the dynatron kink and restoring linear amplification over wide plate voltage swings.
Beam Power Tetrodes: In tubes like the 6146B and 4CX250B , physical suppressor grid wires are replaced by beam-forming plates and aligned control/screen grid wires. This focuses electrons into dense sheets, creating a concentrated negative space-charge potential minimum between the screen and plate that repels secondary electrons without the electrical losses of a physical wire grid.
Comparison of Valve Types
Valve Type Electrodes Internal Capacitance ( C a g C_{ag} C a g ) Neutralisation Needed? Secondary Emission Effect Primary Application
Diode Anode, Cathode N/A No None High-voltage mains rectifiers (e.g. 3B28)
Triode Anode, Grid, Cathode High ( 2 − 10 pF 2 - 10\text{ pF} 2 − 10 pF ) Yes (in grid-driven mode) Secondary electrons return to anode Grounded-grid HF power amplifiers (3-500Z)
Tetrode Anode, Screen, Grid, Cathode Low ( 0.05 − 0.1 pF 0.05 - 0.1\text{ pF} 0.05 − 0.1 pF ) Rarely at HF Dynatron negative resistance kink Legacy audio stages, small RF amplifiers
Pentode Anode, Suppressor, Screen, Grid, Cathode Very Low ( < 0.03 pF < 0.03\text{ pF} < 0.03 pF ) Often unnecessary at HF; may be needed at higher frequencies Suppressed by G3 electrostatic barrier RF receivers, wide-swing linear transmitters
Beam Power Anode, Beam Plates, Screen, Grid, Cathode Very Low ( < 0.05 pF < 0.05\text{ pF} < 0.05 pF ) Depends on circuit and frequency Suppressed by electron beam space charge High-efficiency linear PAs (6146B, 4CX250B)
Grounded-Grid Linear Amplifiers for Amateur HF Transmission
In modern amateur radio high-power linear amplifiers (such as dual 3-500Z or 811A amplifiers), the grounded-grid triode configuration is universally favored over grid-driven circuits. +HV DC
- |
- RFC
- |
- ANODE -------------+---[C_block]---[Pi / Pi-L]---> RF load
- |
- [ TRIODE ]
- GND -- CONTROL GRID
- |
- CATHODE <---[C_in]---[Input matching]--- 50-ohm exciter
- |
- Filament RF choke
- |
- Isolated filament supply
This functional diagram omits the filament's second lead, bias, metering and protection circuits. C block C_{\text{block}} C block keeps plate DC out of the output network; C in C_{\text{in}} C in couples the drive while blocking DC.
Operational Architecture
The control grid is connected directly to RF ground (often bolted directly to the chassis with zero lead inductance).
The RF drive reaches the cathode through a coupling capacitor and input matching network. A bifilar filament RF choke isolates the filament supply from the RF drive.
Output power is extracted from the plate via a resonant π \pi π or π \pi π -L matching network.
Four Major Technical Advantages
Good Input–Output Isolation: The grounded grid screens the cathode input from the plate output. Suitable triode stages normally operate without neutralisation at HF, but low-inductance grounding, layout and suppression of parasitic oscillations remain important.
Low Input Impedance Matches Solid-State Transceivers: The input impedance looking into the cathode is approximately R in ≈ 1 / g m R_{\text{in}} \approx 1 / g_m R in ≈ 1/ g m (typically 50 Ω 50\ \Omega 50 Ω to 100 Ω 100\ \Omega 100 Ω ). This provides an almost ideal match to standard 50 Ω 50\ \Omega 50 Ω solid-state transceivers using simple, switchable input tuned LC networks.
Drive Power Feed-Through Addition: In a grounded-grid stage, the input driving source is in series with the plate load circuit. Part of the exciter’s RF drive ( 50 W 50\text{ W} 50 W to 100 W 100\text{ W} 100 W ) feeds through in phase and adds to the output; grid and input-circuit losses consume the rest. Denote this contribution by P feed P_{\text{feed}} P feed : P total = P plate + P feed P_{\text{total}} = P_{\text{plate}} + P_{\text{feed}} P total = P plate + P feed
Negative Feedback and Linearity: Cathode drive provides degenerative feedback that helps reduce intermodulation distortion. Correct bias, loading, input tuning and drive level are still necessary for linear SSB amplification.
High-Voltage Safety Precautions with Valve Amplifiers
Valve linear amplifiers employ lethal DC plate voltages ranging from 1500 V 1500\text{ V} 1500 V to 3500 V 3500\text{ V} 3500 V , with power supplies capable of delivering sustained currents exceeding 500 mA 500\text{ mA} 500 mA to 1 A 1\text{ A} 1 A .
Caution
Both mains and valve plate supplies can cause fatal shock and severe burns. Injury depends on current, path and duration; switching off does not remove charge stored in the filter capacitors.
Stored Energy in Filter Capacitors
High-voltage filter capacitors store lethal quantities of electrical energy even hours after the amplifier has been switched off and unplugged from the AC mains: E = 1 2 C V 2 E = \frac{1}{2} C V^2 E = 2 1 C V 2
Stored energy alone does not define a universal safe or lethal threshold; voltage, discharge path and contact conditions also matter. A typical linear amplifier supply with a 30 μ F 30\ \mu\text{F} 30 μ F capacitor bank at 2500 V 2500\text{ V} 2500 V stores: E = 1 2 × ( 30 × 10 − 6 F ) × ( 2500 V ) 2 = 0.5 × ( 30 × 10 − 6 ) × 6 , 250 , 000 = 93.75 Joules E = \frac{1}{2} \times (30 \times 10^{-6}\text{ F}) \times (2500\text{ V})^2 = 0.5 \times (30 \times 10^{-6}) \times 6,250,000 = 93.75\text{ Joules} E = 2 1 × ( 30 × 1 0 − 6 F ) × ( 2500 V ) 2 = 0.5 × ( 30 × 1 0 − 6 ) × 6 , 250 , 000 = 93.75 Joules
This stored energy presents a severe shock and burn hazard even after mains power is disconnected.
High-Voltage Safety Measures
Bleeder Resistors: Properly rated resistors provide a permanent discharge path. Resistors across individual series capacitors also help equalise voltage. Design discharge time and continuous power dissipation together; a failed bleeder can leave the bank charged.
Cabinet Interlocks: Interlocks remove power when access covers open. Some equipment also has engineered grounding mechanisms. Neither an interlock nor a front-panel meter proves that every internal circuit is de-energised.
Servicing: High-voltage servicing requires a qualified person following the equipment's isolation, rated discharge and grounding procedure. Disconnect and secure every energy source, discharge stored energy with suitable equipment, and independently verify absence of hazardous voltage with an appropriately rated tester. Verify the tester's operation before and after testing; account for charge recovery. Do not use a screwdriver to short a charged capacitor.
Warm-Up and Cooling: Follow the tube and amplifier manufacturer's heater warm-up delay, voltage sequence and cooling requirements before applying high voltage or RF drive. These depend on the tube and equipment.
- Worked Engineering Calculations
- Example 1: Valve Dynamic Parameters Calculation
Problem: A transmitting triode operating in an RF amplifier shows the following static test results:
With control grid voltage held at V g = − 15 V V_g = -15\text{ V} V g = − 15 V , increasing plate voltage from 1800 V 1800\text{ V} 1800 V to 2200 V 2200\text{ V} 2200 V causes plate current to rise from 120 mA 120\text{ mA} 120 mA to 180 mA 180\text{ mA} 180 mA .
With plate voltage held at V a = 2000 V V_a = 2000\text{ V} V a = 2000 V , changing control grid voltage from − 12 V -12\text{ V} − 12 V to − 18 V -18\text{ V} − 18 V causes plate current to drop from 190 mA 190\text{ mA} 190 mA to 110 mA 110\text{ mA} 110 mA .
Calculate:
The dynamic anode resistance ( r a r_a r a ).
The transconductance ( g m g_m g m ).
The amplification factor ( μ \mu μ ).
Solution:
Dynamic Anode Resistance ( r a r_a r a ): r a = Δ V a Δ I a ∣ V g = − 15 V = 2200 V − 1800 V 180 mA − 120 mA = 400 V 0.060 A = 6 , 667 Ω r_a = \left. \frac{\Delta V_a}{\Delta I_a} \right|_{V_g = -15\text{ V}} = \frac{2200\text{ V} - 1800\text{ V}}{180\text{ mA} - 120\text{ mA}} = \frac{400\text{ V}}{0.060\text{ A}} = 6,667\ \Omega r a = Δ I a Δ V a V g = − 15 V = 180 mA − 120 mA 2200 V − 1800 V = 0.060 A 400 V = 6 , 667 Ω
Transconductance ( g m g_m g m ): g m = Δ I a Δ V g ∣ V a = 2000 V = 190 mA − 110 mA − 12 V − ( − 18 V ) = 80 mA 6 V = 13.33 mA/V = 13.33 mS g_m = \left. \frac{\Delta I_a}{\Delta V_g} \right|_{V_a = 2000\text{ V}} = \frac{190\text{ mA} - 110\text{ mA}}{-12\text{ V} - (-18\text{ V})} = \frac{80\text{ mA}}{6\text{ V}} = 13.33\text{ mA/V} = 13.33\text{ mS} g m = Δ V g Δ I a V a = 2000 V = − 12 V − ( − 18 V ) 190 mA − 110 mA = 6 V 80 mA = 13.33 mA/V = 13.33 mS
Amplification Factor ( μ \mu μ ): μ = g m × r a = 0.01333 S × 6 , 667 Ω = 88.9 \mu = g_m \times r_a = 0.01333\text{ S} \times 6,667\ \Omega = 88.9 μ = g m × r a = 0.01333 S × 6 , 667 Ω = 88.9
Example 2: Capacitor Stored Energy and Bleeder Sizing
Problem: An amateur linear amplifier uses a plate power supply delivering 2800 V 2800\text{ V} 2800 V DC smoothed by a 25 μ F 25\ \mu\text{F} 25 μ F capacitor.
Calculate the energy stored in the capacitor bank under normal operation.
Determine the required bleeder resistance ( R b R_b R b ) to achieve a discharge time constant of τ = 10 seconds \tau = 10\text{ seconds} τ = 10 seconds .
Calculate the power dissipated continuously by this bleeder resistor during normal operation.
Solution:
Stored Electrical Energy: E = 1 2 C V 2 = 0.5 × ( 25 × 10 − 6 F ) × ( 2800 V ) 2 = 0.5 × ( 25 × 10 − 6 ) × 7 , 840 , 000 = 98.0 Joules E = \frac{1}{2} C V^2 = 0.5 \times (25 \times 10^{-6}\text{ F}) \times (2800\text{ V})^2 = 0.5 \times (25 \times 10^{-6}) \times 7,840,000 = 98.0\text{ Joules} E = 2 1 C V 2 = 0.5 × ( 25 × 1 0 − 6 F ) × ( 2800 V ) 2 = 0.5 × ( 25 × 1 0 − 6 ) × 7 , 840 , 000 = 98.0 Joules
(This remains a severe stored-energy hazard after power is removed.)
Bleeder Resistor Value: The discharge time constant is τ = R b × C \tau = R_b \times C τ = R b × C . Rearranging for R b R_b R b : R b = τ C = 10 s 25 × 10 − 6 F = 400 , 000 Ω = 400 k Ω R_b = \frac{\tau}{C} = \frac{10\text{ s}}{25 \times 10^{-6}\text{ F}} = 400,000\ \Omega = 400\text{ k}\Omega R b = C τ = 25 × 1 0 − 6 F 10 s = 400 , 000 Ω = 400 k Ω
Power Dissipated in Bleeder Resistor: P b = V 2 R b = ( 2800 V ) 2 400 , 000 Ω = 7 , 840 , 000 400 , 000 = 19.6 Watts P_b = \frac{V^2}{R_b} = \frac{(2800\text{ V})^2}{400,000\ \Omega} = \frac{7,840,000}{400,000} = 19.6\text{ Watts} P b = R b V 2 = 400 , 000 Ω ( 2800 V ) 2 = 400 , 000 7 , 840 , 000 = 19.6 Watts
(A resistor bank needs suitable voltage and power ratings. After one 10 s 10\text{ s} 10 s time constant, the ideal voltage is still 2800 / e ≈ 1030 V 2800/e\approx1030\text{ V} 2800/ e ≈ 1030 V ; calculated decay is not proof that a real circuit is safe to touch.)