Study guide

8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

Key Takeaways Explain This Topic AI

The input impedance of a lossless transmission line depends cyclically on its electrical length and termination, governed by the general impedance transformation equation Z in = Z 0 [ ( Z L + j Z 0 tan ⁡ β l ) / ( Z 0 + j Z L tan ⁡ β l ) ] Z_{\text{in}} = Z_0 [(Z_L + j Z_0 \tan \beta l) / (Z_0 + j Z_L \tan \beta l)] Z in ​ = Z 0 ​ [( Z L ​ + j Z 0 ​ tan βl ) / ( Z 0 ​ + j Z L ​ tan βl )] .

A quarter-wave ( λ / 4 \lambda/4 λ /4 ) transmission line section acts as an impedance inverter ( Z in = Z 0 2 / Z L Z_{\text{in}} = Z_0^2 / Z_L Z in ​ = Z 0 2 ​ / Z L ​ ), transforming an open circuit into a short circuit (series resonance) and a short circuit into an open circuit (parallel resonance).

Quarter-wave matching transformers match two real resistive impedances R 1 R_1 R 1 ​ and R 2 R_2 R 2 ​ when engineered with a characteristic impedance of Z 0 = R 1 R 2 Z_0 = \sqrt{R_1 R_2} Z 0 ​ = R 1 ​ R 2 ​ ​ , such as using a 70.7 Ω 70.7\ \Omega 70.7 Ω line to match a 50 Ω 50\ \Omega 50 Ω feedline to a 100 Ω 100\ \Omega 100 Ω antenna load.

A half-wave ( λ / 2 \lambda/2 λ /2 ) line section acts as a 1:1 impedance repeater ( Z in = Z L Z_{\text{in}} = Z_L Z in ​ = Z L ​ ), mirroring the terminating load impedance at the input regardless of the feedline's characteristic impedance.

Transmission line stubs shorter than λ / 4 \lambda/4 λ /4 exhibit pure reactance: short-circuited stubs behave as inductors ( Z in = + j Z 0 tan ⁡ β l Z_{\text{in}} = +jZ_0 \tan \beta l Z in ​ = + j Z 0 ​ tan βl ), while open-circuited stubs behave as capacitors ( Z in = − j Z 0 cot ⁡ β l Z_{\text{in}} = -jZ_0 \cot \beta l Z in ​ = − j Z 0 ​ cot βl ), widely employed for harmonic notch filtering and coaxial reactive matching.

Last updated: November 2026

8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

In conventional low-frequency electronics, reactive impedance is realized exclusively through physical inductors and capacitors. At radio frequencies—particularly across the VHF, UHF, and microwave spectra—physical lumped components suffer from severe parasitic effects: inductors exhibit distributed inter-turn capacitance, and capacitors exhibit lead inductance and dielectric heating. To circumvent these limitations, RF engineers exploit a remarkable property of transmission lines: a section of transmission line transforms impedances along its length .

By carefully choosing the line's characteristic impedance ( Z 0 Z_0 Z 0 ​ ), electrical length ( l l l ), and terminal condition (shorted, open, or loaded), a simple section of coaxial cable or parallel open-wire line can function as an impedance inverter, an impedance repeater, an ultra-low-loss tuned resonant tank, an inductive choke, a capacitive trimmer, or a notch filter.

The General Transmission Line Input Impedance Equation

Consider a lossless uniform transmission line of characteristic impedance Z 0 Z_0 Z 0 ​ , terminated at x = 0 x = 0 x = 0 with an arbitrary complex load impedance Z L Z_L Z L ​ . At any distance l l l from the load (looking back into the line toward the load), the input impedance ( Z in Z_{\text{in}} Z in ​ ) is the ratio of total line voltage to total line current: Z in ( l ) = V ( l ) I ( l ) = V + e + j β l + V − e − j β l V + Z 0 e + j β l − V − Z 0 e − j β l Z_{\text{in}}(l) = \frac{V(l)}{I(l)} = \frac{V^+ e^{+j\beta l} + V^- e^{-j\beta l}}{\frac{V^+}{Z_0} e^{+j\beta l} - \frac{V^-}{Z_0} e^{-j\beta l}} Z in ​ ( l ) = I ( l ) V ( l ) ​ = Z 0 ​ V + ​ e + j βl − Z 0 ​ V − ​ e − j βl V + e + j βl + V − e − j βl ​

Substituting V − = Γ V + V^- = \Gamma V^+ V − = Γ V + and Γ = ( Z L − Z 0 ) / ( Z L + Z 0 ) \Gamma = (Z_L - Z_0) / (Z_L + Z_0) Γ = ( Z L ​ − Z 0 ​ ) / ( Z L ​ + Z 0 ​ ) , and expressing the complex exponentials in terms of Euler's trigonometric identities ( cos ⁡ β l \cos \beta l cos βl and j sin ⁡ β l j \sin \beta l j sin βl ), yields the classical General Transmission Line Input Impedance Equation : Z in ( l ) = Z 0 [ Z L + j Z 0 tan ⁡ ( β l ) Z 0 + j Z L tan ⁡ ( β l ) ] Z_{\text{in}}(l) = Z_0 \left[ \frac{Z_L + j Z_0 \tan(\beta l)}{Z_0 + j Z_L \tan(\beta l)} \right] Z in ​ ( l ) = Z 0 ​ [ Z 0 ​ + j Z L ​ tan ( βl ) Z L ​ + j Z 0 ​ tan ( βl ) ​ ]

where:

β = 2 π λ \beta = \frac{2\pi}{\lambda} β = λ 2 π ​ is the phase constant in radians per meter.

l l l is the physical length of the line section.

β l \beta l βl is the electrical length of the line section in radians (where 2 π rad = 360 ∘ = 1 λ 2\pi\text{ rad} = 360^\circ = 1\lambda 2 π rad = 36 0 ∘ = 1 λ ).

Because the tangent function is periodic with a period of π \pi π radians ( 180 ∘ 180^\circ 18 0 ∘ , or λ / 2 \lambda/2 λ /2 ), the input impedance transforms cyclically along the line, repeating its exact value every electrical half-wavelength.

Quarter-Wave ( λ / 4 \lambda/4 λ /4 ) Line Sections and Impedance Inversion

A transmission line whose electrical length is an odd multiple of a quarter-wavelength ( l = λ / 4 , 3 λ / 4 , 5 λ / 4 , … l = \lambda/4, 3\lambda/4, 5\lambda/4, \dots l = λ /4 , 3 λ /4 , 5 λ /4 , … ) exhibits unique and powerful impedance transformation properties.

When l = λ / 4 l = \lambda/4 l = λ /4 , the electrical angle is β l = ( 2 π / λ ) ( λ / 4 ) = π / 2 \beta l = (2\pi / \lambda)(\lambda / 4) = \pi / 2 βl = ( 2 π / λ ) ( λ /4 ) = π /2 radians ( 90 ∘ 90^\circ 9 0 ∘ ). As β l \beta l βl approaches π / 2 \pi / 2 π /2 , tan ⁡ ( β l ) \tan(\beta l) tan ( βl ) approaches infinity ( tan ⁡ ( π / 2 ) → ∞ \tan(\pi/2) \to \infty tan ( π /2 ) → ∞ ). Dividing the numerator and denominator of the general impedance equation by tan ⁡ ( β l ) \tan(\beta l) tan ( βl ) : Z in = Z 0 lim ⁡ β l → π / 2 [ Z L tan ⁡ ( β l ) + j Z 0 Z 0 tan ⁡ ( β l ) + j Z L ] = Z 0 [ 0 + j Z 0 0 + j Z L ] = Z 0 ( Z 0 Z L ) Z_{\text{in}} = Z_0 \lim_{\beta l \to \pi/2} \left[ \frac{\frac{Z_L}{\tan(\beta l)} + j Z_0}{\frac{Z_0}{\tan(\beta l)} + j Z_L} \right] = Z_0 \left[ \frac{0 + j Z_0}{0 + j Z_L} \right] = Z_0 \left( \frac{Z_0}{Z_L} \right) Z in ​ = Z 0 ​ βl → π /2 lim ​ [ t a n ( βl ) Z 0 ​ ​ + j Z L ​ t a n ( βl ) Z L ​ ​ + j Z 0 ​ ​ ] = Z 0 ​ [ 0 + j Z L ​ 0 + j Z 0 ​ ​ ] = Z 0 ​ ( Z L ​ Z 0 ​ ​ ) Z in = Z 0 2 Z L Z_{\text{in}} = \frac{Z_0^2}{Z_L} Z in ​ = Z L ​ Z 0 2 ​ ​

This is the celebrated Quarter-Wave Impedance Inversion Formula .

Important

A quarter-wavelength transmission line section acts as an impedance inverter :

It transforms a low load impedance into a high input impedance .

It transforms a high load impedance into a low input impedance .

It transforms an inductive load into a capacitive input .

  • It transforms a capacitive load into an inductive input . Input upper o-------- line length lambda/4 -------+
  • |
  • [ Z_L ]
  • |
  • Input return o-------------------------------------+

Z_in = Z_0^2 / Z_L

Short load --> open input; open load --> short input.

Low resistive load --> high input resistance.

Capacitive load --> inductive input, and conversely.

Extreme Resonant Cases of Quarter-Wave Sections

Short-Circuited Quarter-Wave Section ( Z L = 0 Z_L = 0 Z L ​ = 0 ): Z in = Z 0 2 0 → ∞ Z_{\text{in}} = \frac{Z_0^2}{0} \to \infty Z in ​ = 0 Z 0 2 ​ ​ → ∞ A short-circuited quarter-wave line appears at its input terminals as an infinite impedance (open circuit). It behaves identically to an ideal parallel-resonant LC tank circuit at anti-resonance.

Practical Application: Metallic Insulator / Standoff Support. In VHF/UHF antenna arrays and power amplifier cavities, a shorted quarter-wave copper rod or stub can be connected directly between the live RF conductor and a grounded metal chassis. At the operating frequency, it presents infinite impedance and draws zero RF current, acting as a rigid, mechanically robust, weatherproof insulator made entirely of solid metal!

Practical Application: DC Grounding and Surge Protection. A grounded shorted stub provides a DC path for static charge while presenting high impedance at its design frequency. It is not a zero-impedance path for every lightning component: surge current can divide into equipment and on-frequency energy can pass. Use coordinated lightning protection and the device’s specified RF insertion loss and surge ratings.

Open-Circuited Quarter-Wave Section ( Z L = ∞ Z_L = \infty Z L ​ = ∞ ): Z in = Z 0 2 ∞ = 0 Z_{\text{in}} = \frac{Z_0^2}{\infty} = 0 Z in ​ = ∞ Z 0 2 ​ ​ = 0 An open-circuited quarter-wave line appears at its input terminals as a dead short circuit ( Z in = 0 Z_{\text{in}} = 0 Z in ​ = 0 ). It behaves identically to a series-resonant LC circuit at resonance.

Practical Application: Harmonic Notch Stubs. An open quarter-wave stub in shunt presents low impedance at its design frequency. If cut for 2 f 0 2f_0 2 f 0 ​ , it rejects that harmonic but is a capacitive load at f 0 f_0 f 0 ​ . A shorted quarter-wave stub cut for f 0 f_0 f 0 ​ instead presents high impedance at f 0 f_0 f 0 ​ and low impedance at 2 f 0 2f_0 2 f 0 ​ .

Quarter-Wave Matching Transformers (Q-Sections)

The impedance inverting property of quarter-wave sections makes them ideal for matching two disparate, purely resistive impedances, such as transforming an antenna's radiation resistance ( R L R_L R L ​ ) to match a standard feedline ( R source R_{\text{source}} R source ​ ).

From the inversion formula, R in = Z 0 2 / R L R_{\text{in}} = Z_0^2 / R_L R in ​ = Z 0 2 ​ / R L ​ . Setting R in = R source R_{\text{in}} = R_{\text{source}} R in ​ = R source ​ and solving for the required transformer characteristic impedance ( Z 0 Z_0 Z 0 ​ ): Z 0 = R source × R L = R 1 R 2 Z_0 = \sqrt{R_{\text{source}} \times R_L} = \sqrt{R_1 R_2} Z 0 ​ = R source ​ × R L ​ ​ = R 1 ​ R 2 ​ ​

Step-by-Step Worked Example: Matching Two Paralleled Yagi Antennas

An amateur radio operator stacks two identical 2-meter Yagi antennas. Each antenna has a feedpoint impedance of 50 Ω 50\ \Omega 50 Ω . To combine them in parallel, each antenna must first be transformed to 100 Ω 100\ \Omega 100 Ω so that when connected in parallel at a central coaxial tee junction, the total combined impedance is 100 Ω ∥ 100 Ω = 50 Ω 100\ \Omega \parallel 100\ \Omega = 50\ \Omega 100 Ω ∥ 100 Ω = 50 Ω , matching the main station feedline. Dual-Antenna Quarter-Wave Matching Stacking

  • Antenna 1 (50 Ω) o----[ λ/4 Q-Section (Z_0 = 70.7 Ω) ]----+
  • |
  • (T-Junction)
  • | Combined = 50 Ω
  • +--- To Transmitter (50 Ω Coax)
  • |
  • Antenna 2 (50 Ω) o----[ λ/4 Q-Section (Z_0 = 70.7 Ω) ]----+

Step 1: Calculate the required transformer impedance ( Z 0 Z_0 Z 0 ​ ): Z 0 = R ant × R target = 50 Ω × 100 Ω = 5000 ≈ 70.71 Ω Z_0 = \sqrt{R_{\text{ant}} \times R_{\text{target}}} = \sqrt{50\ \Omega \times 100\ \Omega} = \sqrt{5000} \approx 70.71\ \Omega Z 0 ​ = R ant ​ × R target ​ ​ = 50 Ω × 100 Ω ​ = 5000 ​ ≈ 70.71 Ω

Step 2: Practical Implementation: Readily available 75 Ω 75\ \Omega 75 Ω low-loss coaxial cable (such as RG-11/U or RG-6/U) is remarkably close to 70.71 Ω 70.71\ \Omega 70.71 Ω . Substituting Z 0 = 75 Ω Z_0 = 75\ \Omega Z 0 ​ = 75 Ω back into the formula: R in = Z 0 2 R L = 75 2 50 = 5625 50 = 112.5 Ω R_{\text{in}} = \frac{Z_0^2}{R_L} = \frac{75^2}{50} = \frac{5625}{50} = 112.5\ \Omega R in ​ = R L ​ Z 0 2 ​ ​ = 50 7 5 2 ​ = 50 5625 ​ = 112.5 Ω

Paralleling two 112.5 Ω 112.5\ \Omega 112.5 Ω legs yields 112.5 / 2 = 56.25 Ω 112.5 / 2 = 56.25\ \Omega 112.5/2 = 56.25 Ω . The resulting SWR on a 50 Ω 50\ \Omega 50 Ω main feedline is: SWR = 56.25 50 = 1.125 : 1 \text{SWR} = \frac{56.25}{50} = 1.125:1 SWR = 50 56.25 ​ = 1.125 : 1

This produces an imperceptible return loss of 24.6 dB 24.6\text{ dB} 24.6 dB (only 0.35 % 0.35\% 0.35% reflected power), demonstrating why 75 Ω 75\ \Omega 75 Ω cable is universally used by amateurs to build stacking transformers.

Step 3: Calculate the physical length at f = 144.30 MHz f = 144.30\text{ MHz} f = 144.30 MHz : If using RG-11/U foam polyethylene cable with a velocity factor V F = 0.84 VF = 0.84 V F = 0.84 : λ 0 = 2.9979 × 10 8 m/s 144.30 × 10 6 Hz ≈ 2.0775 m \lambda_0 = \frac{2.9979 \times 10^8\text{ m/s}}{144.30 \times 10^6\text{ Hz}} \approx 2.0775\text{ m} λ 0 ​ = 144.30 × 1 0 6 Hz 2.9979 × 1 0 8 m/s ​ ≈ 2.0775 m l phys = λ 0 4 × V F = 2.0775 m 4 × 0.84 ≈ 0.5194 m × 0.84 = 0.4363 m = 43.63 cm l_{\text{phys}} = \frac{\lambda_0}{4} \times VF = \frac{2.0775\text{ m}}{4} \times 0.84 \approx 0.5194\text{ m} \times 0.84 = 0.4363\text{ m} = 43.63\text{ cm} l phys ​ = 4 λ 0 ​ ​ × V F = 4 2.0775 m ​ × 0.84 ≈ 0.5194 m × 0.84 = 0.4363 m = 43.63 cm

Half-Wave ( λ / 2 \lambda/2 λ /2 ) Line Sections: The 1:1 Impedance Repeater

When a transmission line's electrical length is an exact half-wavelength ( l = λ / 2 l = \lambda/2 l = λ /2 ) or an integer multiple of a half-wavelength ( l = n × λ / 2 l = n \times \lambda/2 l = n × λ /2 , where n = 1 , 2 , 3 , … n = 1, 2, 3, \dots n = 1 , 2 , 3 , … ):

The electrical angle is β l = ( 2 π / λ ) ( λ / 2 ) = π \beta l = (2\pi / \lambda)(\lambda / 2) = \pi βl = ( 2 π / λ ) ( λ /2 ) = π radians ( 180 ∘ 180^\circ 18 0 ∘ ). Since tan ⁡ ( π ) = 0 \tan(\pi) = 0 tan ( π ) = 0 , substituting tan ⁡ ( β l ) = 0 \tan(\beta l) = 0 tan ( βl ) = 0 into the general impedance equation produces a dramatic simplification: Z in = Z 0 [ Z L + j Z 0 ( 0 ) Z 0 + j Z L ( 0 ) ] = Z 0 ( Z L Z 0 ) = Z L Z_{\text{in}} = Z_0 \left[ \frac{Z_L + j Z_0 (0)}{Z_0 + j Z_L (0)} \right] = Z_0 \left( \frac{Z_L}{Z_0} \right) = Z_L Z in ​ = Z 0 ​ [ Z 0 ​ + j Z L ​ ( 0 ) Z L ​ + j Z 0 ​ ( 0 ) ​ ] = Z 0 ​ ( Z 0 ​ Z L ​ ​ ) = Z L ​

Note

A half-wavelength transmission line section acts as a 1:1 impedance repeater :

Whatever complex impedance is attached to the load terminals ( Z L = R L + j X L Z_L = R_L + jX_L Z L ​ = R L ​ + j X L ​ ) is reproduced identically at the input terminals ( Z in = Z L Z_{\text{in}} = Z_L Z in ​ = Z L ​ ).

This impedance replication is entirely independent of the characteristic impedance ( Z 0 Z_0 Z 0 ​ ) of the transmission line !

Practical Utility of Half-Wave Repeaters

Remote Antenna Measurements: An analyser measures impedance at its calibrated reference plane. A random feedline transforms the antenna's impedance; this is its input impedance, rather than a false reading. A lossless electrical half-wave repeats the load exactly at the design frequency. Real cable attenuation still changes the result, so accurate remote measurements require calibration at the antenna or compensation for the intervening line.

Equal-Phase Feed Networks: Half-wave lines introduce an exact 180 ∘ 180^\circ 18 0 ∘ phase shift with unity impedance scaling, making them essential for feeding phased vertical arrays, collinear arrays, and balun balance loops.

Non-Resonant Line Sections: Reactive Stubs

An ideal lossless line terminated in an open or short circuit dissipates no real power. Away from its resonant open/short input conditions, it presents reactance and stores electric and magnetic energy. Real stubs also have loss resistance.

1. Short-Circuited Stubs ( Z L = 0 Z_L = 0 Z L ​ = 0 )

Substituting Z L = 0 Z_L = 0 Z L ​ = 0 into the general impedance equation: Z in = Z 0 [ 0 + j Z 0 tan ⁡ ( β l ) Z 0 + j ( 0 ) tan ⁡ ( β l ) ] = + j Z 0 tan ⁡ ( β l ) Z_{\text{in}} = Z_0 \left[ \frac{0 + j Z_0 \tan(\beta l)}{Z_0 + j (0) \tan(\beta l)} \right] = +j Z_0 \tan(\beta l) Z in ​ = Z 0 ​ [ Z 0 ​ + j ( 0 ) tan ( βl ) 0 + j Z 0 ​ tan ( βl ) ​ ] = + j Z 0 ​ tan ( βl )

Length 0 < l < λ / 4 0 < l < \lambda/4 0 < l < λ /4 ( 0 ∘ < β l < 90 ∘ 0^\circ < \beta l < 90^\circ 0 ∘ < βl < 9 0 ∘ ): Because tan ⁡ ( β l ) > 0 \tan(\beta l) > 0 tan ( βl ) > 0 , the input impedance is positive imaginary: + j X L +jX_L + j X L ​ (Pure Inductor) . The effective inductive reactance is: X L = Z 0 tan ⁡ ( β l ) X_L = Z_0 \tan(\beta l) X L ​ = Z 0 ​ tan ( βl )

Length λ / 4 < l < λ / 2 \lambda/4 < l < \lambda/2 λ /4 < l < λ /2 ( 90 ∘ < β l < 180 ∘ 90^\circ < \beta l < 180^\circ 9 0 ∘ < βl < 18 0 ∘ ): Because tan ⁡ ( β l ) < 0 \tan(\beta l) < 0 tan ( βl ) < 0 , the input impedance is negative imaginary: − j X C -jX_C − j X C ​ (Pure Capacitor) . The effective capacitive reactance is: X C = − Z 0 tan ⁡ ( β l ) X_C = -Z_0 \tan(\beta l) X C ​ = − Z 0 ​ tan ( βl )

2. Open-Circuited Stubs ( Z L = ∞ Z_L = \infty Z L ​ = ∞ )

Substituting Z L = ∞ Z_L = \infty Z L ​ = ∞ into the general impedance equation (dividing numerator and denominator by Z L Z_L Z L ​ ): Z in = Z 0 [ 1 + j ( Z 0 / Z L ) tan ⁡ ( β l ) ( Z 0 / Z L ) + j tan ⁡ ( β l ) ] = Z 0 j tan ⁡ ( β l ) = − j Z 0 cot ⁡ ( β l ) Z_{\text{in}} = Z_0 \left[ \frac{1 + j(Z_0 / Z_L) \tan(\beta l)}{(Z_0 / Z_L) + j \tan(\beta l)} \right] = \frac{Z_0}{j \tan(\beta l)} = -j Z_0 \cot(\beta l) Z in ​ = Z 0 ​ [ ( Z 0 ​ / Z L ​ ) + j tan ( βl ) 1 + j ( Z 0 ​ / Z L ​ ) tan ( βl ) ​ ] = j tan ( βl ) Z 0 ​ ​ = − j Z 0 ​ cot ( βl )

Length 0 < l < λ / 4 0 < l < \lambda/4 0 < l < λ /4 ( 0 ∘ < β l < 90 ∘ 0^\circ < \beta l < 90^\circ 0 ∘ < βl < 9 0 ∘ ): Because cot ⁡ ( β l ) > 0 \cot(\beta l) > 0 cot ( βl ) > 0 , the input impedance is negative imaginary: − j X C -jX_C − j X C ​ (Pure Capacitor) . The effective capacitive reactance is: X C = Z 0 cot ⁡ ( β l ) X_C = Z_0 \cot(\beta l) X C ​ = Z 0 ​ cot ( βl )

Length λ / 4 < l < λ / 2 \lambda/4 < l < \lambda/2 λ /4 < l < λ /2 ( 90 ∘ < β l < 180 ∘ 90^\circ < \beta l < 180^\circ 9 0 ∘ < βl < 18 0 ∘ ): Because cot ⁡ ( β l ) < 0 \cot(\beta l) < 0 cot ( βl ) < 0 , the input impedance is positive imaginary: + j X L +jX_L + j X L ​ (Pure Inductor) . The effective inductive reactance is: X L = − Z 0 cot ⁡ ( β l ) X_L = -Z_0 \cot(\beta l) X L ​ = − Z 0 ​ cot ( βl )

Master Summary Table of Stub Impedances

Line Length ( l l l ) Electrical Angle ( β l \beta l βl ) Short-Circuited Stub ( Z L = 0 Z_L = 0 Z L ​ = 0 ) Open-Circuited Stub ( Z L = ∞ Z_L = \infty Z L ​ = ∞ )

l = 0 l = 0 l = 0 0 ∘ 0^\circ 0 ∘ Dead Short ( Z in = 0 Z_{\text{in}} = 0 Z in ​ = 0 ) Open Circuit ( Z in = ∞ Z_{\text{in}} = \infty Z in ​ = ∞ )

0 < l < λ / 4 0 < l < \lambda/4 0 < l < λ /4 0 ∘ < β l < 90 ∘ 0^\circ < \beta l < 90^\circ 0 ∘ < βl < 9 0 ∘ Inductive Reactance ( + j Z 0 tan ⁡ β l +j Z_0 \tan \beta l + j Z 0 ​ tan βl ) Capacitive Reactance ( − j Z 0 cot ⁡ β l -j Z_0 \cot \beta l − j Z 0 ​ cot βl )

l = λ / 4 l = \lambda/4 l = λ /4 90 ∘ 90^\circ 9 0 ∘ Parallel Resonant Tank ( Z in → ∞ Z_{\text{in}} \to \infty Z in ​ → ∞ ) Series Resonant Short ( Z in = 0 Z_{\text{in}} = 0 Z in ​ = 0 )

λ / 4 < l < λ / 2 \lambda/4 < l < \lambda/2 λ /4 < l < λ /2 90 ∘ < β l < 180 ∘ 90^\circ < \beta l < 180^\circ 9 0 ∘ < βl < 18 0 ∘ Capacitive Reactance ( − j Z 0 ∣ tan ⁡ β l ∣ -j Z_0 \lvert\tan \beta l\rvert − j Z 0 ​ ∣ tan βl ∣ ) Inductive Reactance ( + j Z 0 ∣ cot ⁡ β l ∣ +j Z_0 \lvert\cot \beta l\rvert + j Z 0 ​ ∣ cot βl ∣ )

l = λ / 2 l = \lambda/2 l = λ /2 180 ∘ 180^\circ 18 0 ∘ Series Resonant Short ( Z in = 0 Z_{\text{in}} = 0 Z in ​ = 0 ) Parallel Resonant Tank ( Z in → ∞ Z_{\text{in}} \to \infty Z in ​ → ∞ )

Tip

In RF hardware design, short-circuited stubs are generally preferred over open-circuited stubs. Open stubs can radiate RF energy from their open ends (acting as miniature antennas) and can collect dust or moisture that causes high-voltage arc-over across the open conductor tips. Shorted stubs provide a continuous metal path that is mechanically rigid and easily grounded.

Stub Matching Techniques: Single-Stub Tuners

When an antenna feedpoint presents an impedance mismatch containing both resistance and reactance, a single-stub matching network can establish a perfect 1 : 1 1:1 1 : 1 match to a 50 Ω 50\ \Omega 50 Ω feedline without using lumped coils or capacitors. Shunt-stub input Distance d to load

  • Signal from TX o-------+-------------------------+
  • | |
  • [ Z_stub ] [ Z_L ]
  • | |
  • Return to TX o-------+-------------------------+

Z_stub is the input impedance of a complete open- or

short-terminated two-conductor stub of length l.

Matching Principle

Normalize admittance to the main line: y = Y / Y 0 = g + j b y=Y/Y_0=g+jb y = Y / Y 0 ​ = g + jb , where Y 0 = 1 / Z 0 Y_0=1/Z_0 Y 0 ​ = 1/ Z 0 ​ . The normalized quantities are dimensionless.

Move a distance d d d from the load toward the transmitter to a point where g = 1 g=1 g = 1 , so y ( d ) = 1 + j b y(d)=1+jb y ( d ) = 1 + jb .

Connect a shunt stub of length l l l whose normalized input admittance is y stub = − j b y_{\text{stub}}=-jb y stub ​ = − jb .

The susceptances cancel: y total = ( 1 + j b ) − j b = 1 y_{\text{total}}=(1+jb)-jb=1 y total ​ = ( 1 + jb ) − jb = 1 . Thus the physical admittance is Y 0 Y_0 Y 0 ​ , and the input impedance is Z 0 Z_0 Z 0 ​ .

At the design frequency, the lossless main line between the junction and transmitter is matched. The load-side section still has its original standing waves.

  • Practical Amateur Applications of Stubs
  • 1. Coaxial Harmonic Notch Stubs

A shunt stub can suppress a harmonic by presenting low impedance across the feedline at that frequency. Choose its termination and length from the impedance equations:

Shorted stub, quarter-wave at f 0 f_0 f 0 ​ : At f 0 f_0 f 0 ​ , Z in = j Z 0 tan ⁡ 90 ∘ → ∞ Z_{\text{in}}=jZ_0\tan90^\circ\to\infty Z in ​ = j Z 0 ​ tan 9 0 ∘ → ∞ , so the ideal stub leaves the wanted carrier unloaded. At 2 f 0 2f_0 2 f 0 ​ , it is a half-wave long and repeats the short circuit. This rejects the second harmonic by reflection.

Open stub, quarter-wave at 2 f 0 2f_0 2 f 0 ​ : It presents a short at 2 f 0 2f_0 2 f 0 ​ , but at f 0 f_0 f 0 ​ its length is λ / 8 \lambda/8 λ /8 and Z in = − j Z 0 cot ⁡ 45 ∘ = − j Z 0 Z_{\text{in}}=-jZ_0\cot45^\circ=-jZ_0 Z in ​ = − j Z 0 ​ cot 4 5 ∘ = − j Z 0 ​ . For a 50 Ω 50\ \Omega 50 Ω stub this is − j 50 Ω -j50\ \Omega − j 50 Ω in shunt, so the fundamental match must also be assessed.

Open stub, half-wave at f 0 f_0 f 0 ​ : It repeats an open circuit at both f 0 f_0 f 0 ​ and 2 f 0 2f_0 2 f 0 ​ , so it does not provide this second-harmonic notch.

Real notch depth and carrier insertion loss depend on cable loss, connections, physical length and parasitic reactance. Verify the assembled filter's pass and rejection responses at the operating frequencies.

2. Multi-Transmitter Repeater Site Isolation

Closely spaced repeater channels require selective filter or duplexer networks, commonly using high-Q cavities. A shorted quarter-wave resonator has high input impedance at resonance; its coupling and connection determine the network's pass or rejection response. Select and measure isolation at the interfering transmitter frequency together with insertion loss and matching at the wanted receiver frequency.