Study guide

7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection

Key Takeaways Explain This Topic AI

The superheterodyne receiver translates incoming RF signals to one or more fixed Intermediate Frequencies (IFs), allowing high gain and steep-skirted filtering to be engineered at constant, optimized frequencies regardless of tuned RF band.

In ordinary difference-product mixing, the image is at f sig ± 2 f IF f_{\text{sig}}\pm2f_{\text{IF}} f sig ​ ± 2 f IF ​ and produces the same IF as the wanted signal. A single real mixer path needs image rejection before mixing; quadrature image-reject receivers can instead combine I/Q paths to cancel the image.

The "IF Dilemma" establishes a fundamental trade-off: a high intermediate frequency (e.g., 70 MHz 70\text{ MHz} 70 MHz ) places the image frequency 2 f IF 2 f_{\text{IF}} 2 f IF ​ far away from the desired signal for simple RF preselection, whereas a low intermediate frequency (e.g., 455 kHz 455\text{ kHz} 455 kHz ) enables sharp-skirted adjacent-channel selectivity filters with low shape factors.

Dual-conversion superheterodyne architectures resolve the IF dilemma by using a high first IF (e.g., 70.455 MHz 70.455\text{ MHz} 70.455 MHz ) for superior image rejection, followed by a second mixer converting to a low second IF (e.g., 455 kHz 455\text{ kHz} 455 kHz ) for narrow-band channel selectivity.

A crystal roofing filter situated immediately after the first mixer protects subsequent IF amplifier and digital signal processing (DSP) stages from strong out-of-passband signals that would otherwise trigger premature AGC pumping or generate third-order intermodulation distortion.

Last updated: November 2026

7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection

In the early era of wireless communications, receivers relied on Tuned Radio Frequency (TRF) architectures, where multiple cascaded amplifier stages were tuned synchronously to the incoming radio frequency. Ganged capacitors could tune several stages together, but the circuits needed careful alignment to track across a band. Selectivity also varied with frequency: at approximately constant Q Q Q , the absolute bandwidth Δ f = f 0 / Q \Delta f=f_0/Q Δ f = f 0 ​ / Q increases as the tuned frequency rises.

In 1918, Edwin Armstrong solved these limitations by inventing the superheterodyne (supersonic heterodyne) receiver . By translating received RF to a fixed Intermediate Frequency (IF) , above or below the received frequency, gain and selectivity can be optimized at that fixed IF. Today, the superheterodyne remains the gold standard for high-performance amateur radio communications.

1. Superheterodyne Architecture and Functional Blocks

The operation of a classic single-conversion superheterodyne receiver can be traced through its sequential functional stages: Antenna --> RF filter/amplifier --> mixer (+ LO) --> selected IF filter/gain

  • |
  • +-----------------------------------+
  • | CW A1A / SSB J3E: product detector (+ BFO)
  • | AM A3E: envelope or synchronous detector
  • | FM F3E: limiter --> discriminator/PLL detector
  • v
  • audio filter --> squelch gate --> audio amplifier --> speaker

AGC controls appropriate earlier gain stages; squelch controls audio muting.

RF Preselector: A passive bandpass filter or sub-octave preselector situated immediately at the antenna terminal. Its sole duty is to restrict the bandwidth of RF energy reaching the active stages, attenuating powerful out-of-band broadcast transmitters and, crucially, rejecting the receiver's image frequency .

Low-Noise RF Amplifier (LNA): A high-linearity, small-signal amplifier (typically using dual-gate MOSFETs, low-noise JFETs, or PHEMTs) that establishes the receiver's overall Noise Figure ( N F NF NF ) . In high-performance HF receivers where atmospheric noise dominates, this stage is often switchable (e.g. + 10 dB +10\text{ dB} + 10 dB preamp, bypass, or − 6 / − 12 / − 18 dB -6/-12/-18\text{ dB} − 6/ − 12/ − 18 dB step attenuator) to prevent front-end overload in the presence of strong signals.

First Mixer and Local Oscillator (LO): Combines the incoming RF signal with the agile, synthesised LO carrier, translating the signal to the fixed intermediate frequency ( f IF = ∣ f RF − f LO ∣ f_{\text{IF}} = |f_{\text{RF}} - f_{\text{LO}}| f IF ​ = ∣ f RF ​ − f LO ​ ∣ ).

Post-Mixer Roofing Filter: A narrow quartz crystal or L C LC L C filter placed immediately at the mixer output. It restricts the bandwidth of signals entering the downstream IF amplifiers to between 250 Hz 250\text{ Hz} 250 Hz (for CW) and 3 kHz 3\text{ kHz} 3 kHz to 15 kHz 15\text{ kHz} 15 kHz (for SSB/AM), protecting subsequent stages from off-frequency overload.

Intermediate Frequency (IF) Amplifier Strip: The "engine room" of the receiver. It provides the vast majority of the receiver's overall system gain ( 80 dB 80\text{ dB} 80 dB to 100 dB 100\text{ dB} 100 dB ). Fixed-frequency operation lets each stage be optimized for one passband. Cascaded high gain still requires careful layout, shielding and supply decoupling to prevent unwanted feedback and self-oscillation. This stage is governed by the Automatic Gain Control (AGC) loop.

Demodulator / Product Detector: Translates the modulated IF signal down to baseband audio:

For SSB and CW , a product detector (a balanced mixer) multiplies the IF signal with a local carrier generated by a Beat Frequency Oscillator (BFO) .

For AM , an envelope diode detector or synchronous detector is used.

For FM , a quadrature detector, phase-locked loop (PLL), or discriminator demodulates frequency shifts.

Audio Amplifier and Active Filter: Boosts the baseband audio signal to drive headphones or an external loudspeaker, incorporating low-pass and notch filtering to eliminate audio hiss and interfering heterodyne whistles.

Squelch and Automatic Gain Control

Squelch mutes the audio when no acceptable received signal is present. An FM noise-squelch circuit can monitor high-frequency detector noise; carrier-operated squelch uses a signal-strength condition. The threshold determines when audio opens. Set it just high enough to silence idle-channel noise; too high a setting hides weak stations. Opening/monitoring the squelch helps when searching for weak signals.

AGC instead adjusts RF/IF gain over changing signal strengths. It helps maintain a useful audio level and avoids overload in the controlled stages. Squelch is not a sensitivity improvement or a substitute for AGC.

2. Image Frequency Mechanics and Image Rejection Ratio (IRR)

A real mixer produces sum and difference components. In the usual difference-product case with f LO > f IF f_{\text{LO}}>f_{\text{IF}} f LO ​ > f IF ​ , RF signals one IF above or below the LO both produce the selected IF. These are:

The Desired Signal Frequency ( f sig f_{\text{sig}} f sig ​ ) .

The Unwanted Image Frequency ( f image f_{\text{image}} f image ​ ) .

Mathematical Derivation of Image Frequency

Depending on whether the local oscillator is tuned above or below the incoming signal frequency, the mixer operates in one of two modes:

1. High-Side Local Oscillator Injection ( f LO > f sig f_{\text{LO}} > f_{\text{sig}} f LO ​ > f sig ​ )

The LO is tuned above the desired signal: f LO = f sig + f IF f_{\text{LO}} = f_{\text{sig}} + f_{\text{IF}} f LO ​ = f sig ​ + f IF ​ .

An unwanted signal entering the mixer at an even higher frequency can also mix with the LO to yield the difference f IF f_{\text{IF}} f IF ​ : ∣ f image − f LO ∣ = f IF ⟹ f image = f LO + f IF |f_{\text{image}} - f_{\text{LO}}| = f_{\text{IF}} \implies f_{\text{image}} = f_{\text{LO}} + f_{\text{IF}} ∣ f image ​ − f LO ​ ∣ = f IF ​ ⟹ f image ​ = f LO ​ + f IF ​

Substituting f LO = f sig + f IF f_{\text{LO}} = f_{\text{sig}} + f_{\text{IF}} f LO ​ = f sig ​ + f IF ​ into the image equation: f image = ( f sig + f IF ) + f IF = f sig + 2 f IF f_{\text{image}} = (f_{\text{sig}} + f_{\text{IF}}) + f_{\text{IF}} = f_{\text{sig}} + 2 f_{\text{IF}} f image ​ = ( f sig ​ + f IF ​ ) + f IF ​ = f sig ​ + 2 f IF ​

2. Low-Side Local Oscillator Injection ( f LO < f sig f_{\text{LO}} < f_{\text{sig}} f LO ​ < f sig ​ )

The LO is tuned below the desired signal: f LO = f sig − f IF f_{\text{LO}} = f_{\text{sig}} - f_{\text{IF}} f LO ​ = f sig ​ − f IF ​ .

If f LO > f IF f_{\text{LO}}>f_{\text{IF}} f LO ​ > f IF ​ , an unwanted positive-frequency signal below the LO also gives the difference f IF f_{\text{IF}} f IF ​ : ∣ f LO − f image ∣ = f IF ⟹ f image = f LO − f IF |f_{\text{LO}} - f_{\text{image}}| = f_{\text{IF}} \implies f_{\text{image}} = f_{\text{LO}} - f_{\text{IF}} ∣ f LO ​ − f image ​ ∣ = f IF ​ ⟹ f image ​ = f LO ​ − f IF ​

Substituting f LO = f sig − f IF f_{\text{LO}} = f_{\text{sig}} - f_{\text{IF}} f LO ​ = f sig ​ − f IF ​ into the image equation: f image = ( f sig − f IF ) − f IF = f sig − 2 f IF f_{\text{image}} = (f_{\text{sig}} - f_{\text{IF}}) - f_{\text{IF}} = f_{\text{sig}} - 2 f_{\text{IF}} f image ​ = ( f sig ​ − f IF ​ ) − f IF ​ = f sig ​ − 2 f IF ​

Important

Difference-product image separation: When both RF responses are positive frequencies on opposite sides of the LO, their separation is 2 f IF 2f_{\text{IF}} 2 f IF ​ .

If the low-side expression f sig − 2 f IF f_{\text{sig}}-2f_{\text{IF}} f sig ​ − 2 f IF ​ is negative, the positive image is its magnitude. It reaches the IF through the sum product, so the 2 f IF 2f_{\text{IF}} 2 f IF ​ separation rule does not apply to those two positive RF frequencies.

Image Rejection and Receiver Architecture

In a single real mixer path , the desired signal and its image overlap at the same IF. A later frequency-selective filter, including DSP on that one path, cannot separate them. RF filtering before the mixer must therefore attenuate the image.

Important

I/Q image rejection uses a different architecture: two quadrature paths preserve phase information. Combining them with the appropriate phase relationship reinforces the wanted response and cancels the image. This can use analogue or digital processing; amplitude and phase errors limit the rejection.

Image Rejection Ratio (IRR)

The Image Rejection Ratio (IRR) quantifies the receiver's ability to reject signals at the image frequency. It is defined as the ratio of receiver sensitivity at the image frequency to sensitivity at the desired frequency, expressed in decibels: IRR (dB) = 10 log ⁡ 10 ( P in(image) P in(desired) ) for equal IF output power \text{IRR (dB)} = 10 \log_{10}\left( \frac{P_{\text{in(image)}}}{P_{\text{in(desired)}}} \right) \quad \text{for equal IF output power} IRR (dB) = 10 lo g 10 ​ ( P in(desired) ​ P in(image) ​ ​ ) for equal IF output power

For a single tuned L C LC L C preselector circuit with loaded quality factor Q L Q_L Q L ​ , the image rejection ratio can be calculated analytically by: IRR = 1 + Q L 2 ( f image f sig − f sig f image ) 2 \text{IRR} = \sqrt{1 + Q_L^2 \left( \frac{f_{\text{image}}}{f_{\text{sig}}} - \frac{f_{\text{sig}}}{f_{\text{image}}} \right)^2} IRR = 1 + Q L 2 ​ ( f sig ​ f image ​ ​ − f image ​ f sig ​ ​ ) 2 ​

In decibels: IRR (dB) = 20 log ⁡ 10 [ 1 + Q L 2 ( f image f sig − f sig f image ) 2 ] \text{IRR (dB)} = 20 \log_{10}\left[ \sqrt{1 + Q_L^2 \left( \frac{f_{\text{image}}}{f_{\text{sig}}} - \frac{f_{\text{sig}}}{f_{\text{image}}} \right)^2} \right] IRR (dB) = 20 lo g 10 ​ ​ 1 + Q L 2 ​ ( f sig ​ f image ​ ​ − f image ​ f sig ​ ​ ) 2 ​ ​

The required IRR depends on the strength of unwanted signals and the tolerated interference. Compare the receiver specification and measured rejection at the relevant tuning frequency; the IF value alone does not set the rejection.

3. The Choice of Intermediate Frequency: The "IF Dilemma"

Selecting the intermediate frequency represents one of the most famous compromises in radio frequency engineering, universally known as the IF dilemma . THE IF DILEMMA TRADE-OFF

  • High Intermediate Frequency Low Intermediate Frequency
  • (e.g., 70 MHz Up-Conversion) (e.g., 455 kHz Down-Conversion)
  • +--------------------------+ +--------------------------+
  • | EXCELLENT Image Rejection| | POOR Image Rejection |
  • | Image is 140 MHz away; | | Image is 910 kHz away; |
  • | RF filtering is easier | | RF filtering is harder |
  • | at this separation. | | at this separation. |
  • +--------------------------+ +--------------------------+
  • | |
  • +--------------------------+ +--------------------------+
  • | POOR Adjacent Selectivity| | EXCELLENT Selectivity |
  • | High Q needed for narrow | | Low Q needed for narrow |
  • | bandwidth; crystal filter| | bandwidth; steep-skirted |
  • | skirts are broad. | | crystal/mechanical filter|
  • +--------------------------+ +--------------------------+
  • The Trade-Off Analysis

If a HIGH Intermediate Frequency is chosen (e.g. 70.0 MHz 70.0\text{ MHz} 70.0 MHz ):

Image Separation: 2 f IF = 2 × 70 MHz = 140 MHz 2 f_{\text{IF}} = 2 \times 70\text{ MHz} = 140\text{ MHz} 2 f IF ​ = 2 × 70 MHz = 140 MHz . For any HF signal between 1.8 MHz 1.8\text{ MHz} 1.8 MHz and 30 MHz 30\text{ MHz} 30 MHz , the image lies between 141.8 MHz 141.8\text{ MHz} 141.8 MHz and 170 MHz 170\text{ MHz} 170 MHz . This wide separation permits a fixed antenna low-pass filter to attenuate the image while passing HF signals; the rejection depends on its design and construction.

Selectivity Defect: Building a narrow 2.4 kHz 2.4\text{ kHz} 2.4 kHz SSB filter at 70 MHz 70\text{ MHz} 70 MHz requires an extreme fractional filter Q Q Q ( Q = 70 MHz / 2.4 kHz ≈ 29 , 167 Q = 70\text{ MHz} / 2.4\text{ kHz} \approx 29,167 Q = 70 MHz /2.4 kHz ≈ 29 , 167 ). Quartz crystal filters at this frequency have broad, sloppy skirts (high shape factors) and significant insertion loss.

If a LOW Intermediate Frequency is chosen (e.g. 455 kHz 455\text{ kHz} 455 kHz ):

Selectivity Advantage: At 455 kHz 455\text{ kHz} 455 kHz , a 2.4 kHz 2.4\text{ kHz} 2.4 kHz filter requires a fractional Q Q Q of only 455 / 2.4 ≈ 190 455 / 2.4 \approx 190 455/2.4 ≈ 190 . Multi-pole mechanical or ceramic filters easily achieve ultra-steep, "brick-wall" filter skirts with shape factors approaching 1.5 1.5 1.5 .

Image Defect: Image separation is only 2 × 455 kHz = 910 kHz 2 \times 455\text{ kHz} = 910\text{ kHz} 2 × 455 kHz = 910 kHz . On the 28 MHz 28\text{ MHz} 28 MHz (10-meter) band, an image only 910 kHz 910\text{ kHz} 910 kHz away represents a frequency deviation of just 3.25 % 3.25\% 3.25% . Strong image rejection therefore requires more selective RF filtering, often using several tuned circuits. Tracking can be manual or electronic; a motor is not an electrical requirement.

4. The Dual-Conversion Superheterodyne Solution

A dual-conversion superheterodyne can combine a high first IF for easier first-image filtering with a low second IF for narrow channel filtering: +-----------+ RF +-----------+ High 1st IF +----------+ Low 2nd IF +----------+ Audio

| Preselect |--->|X|-->| 1st IF |------>|X|--------->| 2nd IF |------>|X|--------->...

  • +-----------+ ^ | Roofing | ^ | Narrow | ^
  • | | Filter | | | Filter | |
  • +---+ +-----------+ +---+ +----------+ +---+
  • |LO1| |LO2| |BFO|
  • +---+ +---+ +---+

First Conversion (Up-Conversion to High 1st IF): The incoming RF signal is mixed with a synthesised LO to translate it to a high first IF (e.g. 70.455 MHz 70.455\text{ MHz} 70.455 MHz ). With high-side injection, the first image is 140.91 MHz 140.91\text{ MHz} 140.91 MHz above the wanted RF. A suitable fixed antenna low-pass filter can strongly attenuate it.

First Roofing Filter: The signal passes through a crystal roofing filter at 70.455 MHz 70.455\text{ MHz} 70.455 MHz with a bandwidth of 6 kHz 6\text{ kHz} 6 kHz to 15 kHz 15\text{ kHz} 15 kHz , protecting downstream stages.

Second Conversion (Down-Conversion to Low 2nd IF): A second mixer driven by a fixed crystal oscillator ( f LO2 = 70.000 MHz f_{\text{LO2}} = 70.000\text{ MHz} f LO2 ​ = 70.000 MHz ) translates the signal down to a low second IF: 70.455 − 70.000 = 455 kHz 70.455 - 70.000 = \mathbf{455\text{ kHz}} 70.455 − 70.000 = 455 kHz .

Second IF Selectivity: At 455 kHz 455\text{ kHz} 455 kHz , steep mechanical or multi-pole crystal ladder filters provide razor-sharp adjacent-channel selectivity with shape factors under 1.6 1.6 1.6 .

Tip

The Modern Contesting Paradigm: Down-Conversion with 9 MHz Roofing Filters: While high first-IF ( 70 MHz 70\text{ MHz} 70 MHz ) up-conversion was standard in the 1990s, modern elite contest transceivers have returned to a single- or dual-conversion down-conversion architecture with a first IF around 9 MHz 9\text{ MHz} 9 MHz .

Why? Because modern quartz crystal engineering allows manufacturing ultra-narrow 250 Hz 250\text{ Hz} 250 Hz and 500 Hz 500\text{ Hz} 500 Hz CW roofing filters at 9 MHz 9\text{ MHz} 9 MHz . Placing an ultra-narrow roofing filter immediately after the first mixer protects the receiver against massive close-in signals just 1 kHz 1\text{ kHz} 1 kHz to 2 kHz 2\text{ kHz} 2 kHz away, yielding unprecedented dynamic range.

5. Roofing Filter Function and Placement

The roofing filter is a narrow crystal ladder filter positioned immediately after the first mixer and IF diplexer network.

The Overload Mechanism: Consider a wanted CW signal of 0.1 μ V 0.1\ \mu\text{V} 0.1 μ V and an interferer of 100 mV 100\text{ mV} 100 mV , measured RMS across a 50 Ω 50\ \Omega 50 Ω receiver input. These are approximately − 127 dBm -127\text{ dBm} − 127 dBm and − 7 dBm -7\text{ dBm} − 7 dBm , a 120 dB 120\text{ dB} 120 dB difference. Let the interferer be 3 kHz 3\text{ kHz} 3 kHz away.

Without a Narrow Roofing Filter: A 15 kHz 15\text{ kHz} 15 kHz first-IF passband can admit both signals to the following IF amplifier. Depending on gain and headroom, the interferer can cause compression, cross-modulation or AGC gain reduction that masks the wanted signal.

With a Narrow Roofing Filter: Use its specified response at the interferer's offset. If it supplies 60 dB 60\text{ dB} 60 dB more attenuation there than at the wanted frequency, the 120 dB 120\text{ dB} 120 dB difference falls to 60 dB 60\text{ dB} 60 dB before later IF/ADC stages. This improves their headroom, but the RF amplifier and first mixer ahead of the filter still need adequate strong-signal performance.

6. Architecture Comparison Table

Receiver Architecture Number of Mixers First Intermediate Frequency Image Rejection Mechanism Close-In Selectivity Skirts Complexity / Cost

Direct Conversion (Homodyne) 1 real path, or 2 mixers for I/Q 0 Hz 0\text{ Hz} 0 Hz (Baseband) Opposite sidebands overlap in one real path; I/Q processing can separate them Handled entirely by low-pass audio/DSP filters Very Low

Single-Conversion Low IF 1 Low ( 455 kHz 455\text{ kHz} 455 kHz or 9 MHz 9\text{ MHz} 9 MHz ) RF filtering selected for the image separation Excellent (Steep crystal/mechanical filters) Low to Moderate

Classic Up-Conversion 2 High ( 60 MHz 60\text{ MHz} 60 MHz to 75 MHz 75\text{ MHz} 75 MHz ) Fixed antenna LPF; rejection depends on the filter Moderate (Limited by broad high-frequency roofing filters) Moderate

Modern Down-Conversion Dual-IF 2 Moderate ( 9 MHz 9\text{ MHz} 9 MHz ) + Low ( 455 kHz 455\text{ kHz} 455 kHz or DSP) Band-switched sub-octave preselectors Superior (Narrow 250 Hz − 3 kHz 250\text{ Hz} - 3\text{ kHz} 250 Hz − 3 kHz crystal roofing filters immediately after 1st mixer) High

  • 7. Worked Engineering Examples
  • Worked Example 7.3.1: Image Frequency Calculations for High-Side and Low-Side Injection

An amateur communications receiver utilizes a first intermediate frequency of f IF = 9.000 MHz f_{\text{IF}} = 9.000\text{ MHz} f IF ​ = 9.000 MHz . Calculate the local oscillator frequency and the resulting image frequency under two different tuning scenarios:

Scenario A: The receiver is tuned to f sig = 7.150 MHz f_{\text{sig}} = 7.150\text{ MHz} f sig ​ = 7.150 MHz on the 40-meter band using high-side local oscillator injection : f LO = f sig + f IF = 7.150 MHz + 9.000 MHz = 16.150 MHz f_{\text{LO}} = f_{\text{sig}} + f_{\text{IF}} = 7.150\text{ MHz} + 9.000\text{ MHz} = 16.150\text{ MHz} f LO ​ = f sig ​ + f IF ​ = 7.150 MHz + 9.000 MHz = 16.150 MHz f image = f sig + 2 f IF = 7.150 MHz + ( 2 × 9.000 MHz ) = 25.150 MHz f_{\text{image}} = f_{\text{sig}} + 2 f_{\text{IF}} = 7.150\text{ MHz} + (2 \times 9.000\text{ MHz}) = 25.150\text{ MHz} f image ​ = f sig ​ + 2 f IF ​ = 7.150 MHz + ( 2 × 9.000 MHz ) = 25.150 MHz

The image lies at 25.150 MHz 25.150\text{ MHz} 25.150 MHz . An unwanted signal there could produce the same IF, so the 40-metre preselector must attenuate that frequency.

Scenario B: The receiver is tuned to f sig = 14.250 MHz f_{\text{sig}}=14.250\text{ MHz} f sig ​ = 14.250 MHz using low-side injection : f LO = 14.250 − 9.000 = 5.250 MHz f_{\text{LO}}=14.250-9.000=5.250\text{ MHz} f LO ​ = 14.250 − 9.000 = 5.250 MHz

The expression 14.250 − 2 ( 9.000 ) = − 3.750 MHz 14.250-2(9.000)=-3.750\text{ MHz} 14.250 − 2 ( 9.000 ) = − 3.750 MHz identifies a positive image at 3.750 MHz 3.750\text{ MHz} 3.750 MHz . Check its actual mixing product: f image + f LO = 3.750 + 5.250 = 9.000 MHz f_{\text{image}}+f_{\text{LO}}=3.750+5.250=9.000\text{ MHz} f image ​ + f LO ​ = 3.750 + 5.250 = 9.000 MHz

The wanted signal uses the difference 14.250 − 5.250 = 9.000 MHz 14.250-5.250=9.000\text{ MHz} 14.250 − 5.250 = 9.000 MHz ; the image uses the sum. Their separation is 14.250 − 3.750 = 10.500 MHz 14.250-3.750=10.500\text{ MHz} 14.250 − 3.750 = 10.500 MHz , not 2 f IF 2f_{\text{IF}} 2 f IF ​ . RF preselection must reject the 3.750 MHz 3.750\text{ MHz} 3.750 MHz response.

Worked Example 7.3.2: Calculating Image Rejection Ratio (IRR) from Preselector Quality Factor

A receiver front-end consists of a single parallel L C LC L C resonant preselector tuned to f sig = 14.100 MHz f_{\text{sig}} = 14.100\text{ MHz} f sig ​ = 14.100 MHz . The loaded quality factor of the tank circuit is Q L = 40 Q_L = 40 Q L ​ = 40 . The receiver uses a low IF of f IF = 455 kHz f_{\text{IF}} = 455\text{ kHz} f IF ​ = 455 kHz with high-side LO injection.

Calculate the image frequency: f image = f sig + 2 f IF = 14.100 MHz + ( 2 × 0.455 MHz ) = 15.010 MHz f_{\text{image}} = f_{\text{sig}} + 2 f_{\text{IF}} = 14.100\text{ MHz} + (2 \times 0.455\text{ MHz}) = 15.010\text{ MHz} f image ​ = f sig ​ + 2 f IF ​ = 14.100 MHz + ( 2 × 0.455 MHz ) = 15.010 MHz

Calculate the normalized frequency detuning parameter ( y y y ): y = f image f sig − f sig f image = 15.010 14.100 − 14.100 15.010 = 1.0645 − 0.9394 = 0.1251 y = \frac{f_{\text{image}}}{f_{\text{sig}}} - \frac{f_{\text{sig}}}{f_{\text{image}}} = \frac{15.010}{14.100} - \frac{14.100}{15.010} = 1.0645 - 0.9394 = 0.1251 y = f sig ​ f image ​ ​ − f image ​ f sig ​ ​ = 14.100 15.010 ​ − 15.010 14.100 ​ = 1.0645 − 0.9394 = 0.1251

Calculate the Image Rejection Ratio: IRR = 1 + ( Q L ⋅ y ) 2 = 1 + ( 40 × 0.1251 ) 2 = 1 + ( 5.004 ) 2 = 1 + 25.04 = 26.04 ≈ 5.103 \text{IRR} = \sqrt{1 + (Q_L \cdot y)^2} = \sqrt{1 + (40 \times 0.1251)^2} = \sqrt{1 + (5.004)^2} = \sqrt{1 + 25.04} = \sqrt{26.04} \approx 5.103 IRR = 1 + ( Q L ​ ⋅ y ) 2 ​ = 1 + ( 40 × 0.1251 ) 2 ​ = 1 + ( 5.004 ) 2 ​ = 1 + 25.04 ​ = 26.04 ​ ≈ 5.103

Express the IRR in decibels: IRR (dB) = 20 log ⁡ 10 ( 5.103 ) ≈ 14.16 dB \text{IRR (dB)} = 20 \log_{10}(5.103) \approx 14.16\text{ dB} IRR (dB) = 20 lo g 10 ​ ( 5.103 ) ≈ 14.16 dB

Analysis: The single tank attenuates this image by only 14.16 dB 14.16\text{ dB} 14.16 dB . An image signal more than 14.16 dB 14.16\text{ dB} 14.16 dB stronger than the wanted signal would still give a larger IF output. More selective RF filtering or a different frequency plan can improve rejection. The result demonstrates this particular preselector's limitation; it does not prove that all single-conversion HF receivers must use one architecture or tuning mechanism.