Study guide

12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation

Key Takeaways Explain This Topic AI

Sporadic-E ( E s E_s E s ​ ) propagation occurs when neutral wind shears in the 95 to 115 km 95\text{ to }115\text{ km} 95 to 115 km altitude region compress long-lived metallic ions ( F e + , M g + , C a + Fe^+, Mg^+, Ca^+ F e + , M g + , C a + from ablated meteors) into ultra-thin, highly dense plasma sheets capable of reflecting signals up to 50 MHz 50\text{ MHz} 50 MHz and 144 MHz 144\text{ MHz} 144 MHz .

Sporadic-E has a prominent Australian summer season and a smaller winter season. Many single-hop VHF contacts span roughly 1000 to 2200 km 1000\text{ to }2200\text{ km} 1000 to 2200 km ; the actual skip distance and signal strength depend on frequency, ionisation, geometry and the station equipment.

Auroral particle precipitation produces ionisation with field-aligned irregularities. Doppler spreading gives VHF signals a characteristic buzz or rasp. CW is usually easiest to copy; distorted SSB can also be usable, especially on 50 MHz 50\text{ MHz} 50 MHz .

For auroral scatter, both stations aim toward a suitable common volume of auroral ionisation. Australian operators usually search in the southern sky and adjust for maximum signal; a fixed due-south bearing is not required.

TEP crosses the geomagnetic equator through the F F F region. Afternoon TEP chiefly supports lower VHF, including 50 MHz 50\text{ MHz} 50 MHz , by crest-to-crest chordal refraction. Evening TEP is associated with spread-F irregularities, can support 144 MHz 144\text{ MHz} 144 MHz , and may have severe fading and distortion.

Last updated: November 2026

12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation

VHF and UHF communication commonly uses line-of-sight and tropospheric paths because most of these signals penetrate the ionosphere. The lower VHF range can also support ordinary F 2 F_2 F 2 ​ propagation at high solar activity. Sporadic-E ( E s E_s E s ​ ) , auroral scatter , and trans-equatorial propagation (TEP) provide further long-distance paths. They are especially useful on 50 MHz 50\text{ MHz} 50 MHz ; suitable openings on 144 MHz 144\text{ MHz} 144 MHz occur less often and depend strongly on the mechanism and path.

Each of these modes is governed by unique plasma physics, geographical constraints, and temporal cycles. Understanding their underlying physical mechanisms allows operators to anticipate band openings, optimize antenna azimuths, and select appropriate modulation modes.

Sporadic-E ( E s E_s E s ​ ) Propagation

Sporadic-E (designated by the symbol E s E_s E s ​ ) is an anomalous propagation mode that forms within the ionospheric E E E region at altitudes between 95 and 115 km 95\text{ and }115\text{ km} 95 and 115 km . Unlike the regular E E E layer, which is broad, diffuse, and strictly governed by solar ionizing radiation, Sporadic-E consists of isolated, highly concentrated, and remarkably thin sheets of intense ionization. Wind Shear Theory of Sporadic-E Formation

  • Altitude ~115 km: Westward Wind (v_west)
  • -------------------------------------------------->
  • | Magnetic force contributes to ion drift
  • | DOWNWARD toward the convergence layer
  • ▼
  • ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ E_s Layer (~1-2 km thick)
  • Dense Sheet of Metallic Ions (Fe+, Mg+, Ca+)
  • ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  • ▲ Lorentz Force pushes ions UPWARD
  • |
  • <---------------------------------------------------
  • Altitude ~95 km: Eastward Wind (v_east)
  • =================================================================
  • Earth's Surface
  • The Wind Shear Mechanism and Metallic Ions

The contemporary physical explanation for mid-latitude Sporadic-E is the wind shear theory , formulated by Whitehead and Axford. This mechanism relies on two fundamental components:

Long-Lived Metallic Ions: Ablating meteoric material supplies metal atoms and ions, including iron ( Fe + \text{Fe}^+ Fe + ), magnesium ( Mg + \text{Mg}^+ Mg + ), calcium ( Ca + \text{Ca}^+ Ca + ), and silicon ( Si + \text{Si}^+ Si + ). The atomic metal ions persist much longer than the ordinary molecular ions NO + \text{NO}^+ NO + and O 2 + \text{O}_2^+ O 2 + ​ , whose dissociative recombination is rapid. Metal-ion neutralisation commonly requires conversion to a molecular ion before dissociative recombination can occur. Lifetimes can extend to days in the upper part of the E E E region, leaving material that winds can concentrate into a dense layer.

Horizontal Wind Shears and the Lorentz Force: Atmospheric solar tides and internal gravity waves generate powerful horizontal neutral winds in the mesosphere that reverse direction across vertical separations of only a few kilometres (for example, a strong westward wind at 115 km 115\text{ km} 115 km altitude and an eastward wind at 95 km 95\text{ km} 95 km ). As neutral air drags metallic ions across the lines of the geomagnetic field ( B ⃗ \vec{B} B ), the ions experience a vertical Lorentz force : F ⃗ = q ( v ⃗ × B ⃗ ) \vec{F} = q \left( \vec{v} \times \vec{B} \right) F = q ( v × B ) Because the geomagnetic field lines are inclined, an eastward wind drives positive ions upward, while a westward wind above it drives positive ions downward. This vertical compression squeezes the long-lived metallic ions into an ultra-thin, highly dense plasma sheet, often only 1 to 2 km 1\text{ to }2\text{ km} 1 to 2 km thick , but spanning horizontal dimensions of 50 to 500 km 50\text{ to }500\text{ km} 50 to 500 km .

Reflection Geometry and Maximum Usable Frequency (MUF)

Because the plasma sheet is so physically thin and intensely ionised, it behaves almost like an optical mirror rather than a refracting slab. The relationship between the vertical incidence critical frequency ( f o E s f_o E_s f o ​ E s ​ ) and the Maximum Usable Frequency ( f MUF f_{\text{MUF}} f MUF ​ ) for an oblique radio path is governed by Martyn's secant law for flat layers: f MUF = f o E s cos ⁡ θ = f o E s sec ⁡ θ f_{\text{MUF}} = \frac{f_o E_s}{\cos \theta} = f_o E_s \sec \theta f MUF ​ = cos θ f o ​ E s ​ ​ = f o ​ E s ​ sec θ

where θ \theta θ is the angle of incidence relative to the normal of the ionospheric layer. At the lowest practical radiation takeoff angles ( < 3 ∘ < 3^\circ < 3 ∘ ), the geometry of reflection from an altitude of 100 km 100\text{ km} 100 km yields an angle of incidence of approximately θ ≈ 78 ∘ to 80 ∘ \theta \approx 78^\circ\text{ to }80^\circ θ ≈ 7 8 ∘ to 8 0 ∘ , giving a secant factor of sec ⁡ θ ≈ 5.0 \sec \theta \approx 5.0 sec θ ≈ 5.0 .

50 MHz 50\text{ MHz} 50 MHz (6 meters): A vertical critical frequency of only f o E s ≥ 10 MHz f_o E_s \ge 10\text{ MHz} f o ​ E s ​ ≥ 10 MHz is sufficient to support oblique propagation on 50 MHz 50\text{ MHz} 50 MHz . Consequently, 6-meter E s E_s E s ​ openings occur with high frequency.

144 MHz 144\text{ MHz} 144 MHz (2 meters): For an E s E_s E s ​ patch to support 144 MHz 144\text{ MHz} 144 MHz , the vertical critical frequency must reach extreme levels: f o E s ≥ 28 to 30 MHz f_o E_s \ge 28\text{ to }30\text{ MHz} f o ​ E s ​ ≥ 28 to 30 MHz . These intense events occur less frequently, requiring exceptional meteor ionisation and severe wind shears.

Skip Distance and Signal Properties

Single-Hop Range: For a layer near 100 km 100\text{ km} 100 km , Earth curvature gives a maximum ground range of about 2200 km 2200\text{ km} 2200 km with grazing rays. The shortest supported distance is set by operating frequency and layer critical frequency: it is not a fixed geometric minimum. Many VHF openings span roughly 1000 to 2200 km 1000\text{ to }2200\text{ km} 1000 to 2200 km .

Double-Hop Range: Two suitable E s E_s E s ​ regions and an intermediate ground reflection can extend contacts to roughly 3500 to 4200 km 3500\text{ to }4200\text{ km} 3500 to 4200 km .

Signal Strength: Signals can rise rapidly to strong levels, sometimes allowing low-power contacts. A link budget includes free-space spreading, ionospheric loss, antenna gains and any terrain diffraction; neither an opening nor a particular transmitter power guarantees an S 9 S9 S 9 signal.

Temporal Distribution: Australian openings are most common around summer, particularly December and January, with a smaller winter season near June. Daytime and early-evening openings are common, but individual events are irregular and can last from minutes to hours.

Auroral Propagation

Auroral propagation (auroral scatter) is a high-latitude VHF propagation mode driven by solar-terrestrial space weather interactions. It occurs during major geomagnetic storms triggered by Coronal Mass Ejections (CMEs) or coronal hole high-speed solar wind streams impacting Earth's magnetosphere. Auroral scatter: a common scattering region

(schematic, not to scale)

  • Field-aligned irregularities
  • in the auroral E region
  • [ common volume ]
  • / \
  • uplink / \ downlink
  • / \
  • Station 1 Station 2

Both antennas illuminate the same suitable region of the oval.

In southern Australia, begin searching in the southern sky;

the strongest bearings can differ and need not be due south.

Auroral Ionisation and Doppler Spread

During enhanced geomagnetic activity, energetic particles precipitate along magnetic field lines into the auroral atmosphere. Collisions with atmospheric gases cause ionisation and visible emission. VHF auroral scatter commonly involves irregularities in the E E E region near 100 to 120 km 100\text{ to }120\text{ km} 100 to 120 km . Strong storms can extend the auroral oval toward lower latitudes; the planetary K p K_p K p ​ index indicates disturbance but does not by itself guarantee a usable path at a particular station.

The scattering irregularities are elongated along the magnetic field. Electric fields, plasma waves and motion within the scattering region produce a range of Doppler shifts. A received signal can be broadened by hundreds of hertz, with the amount depending on frequency, propagation geometry and the irregularities. The simple shift 2 v radial / λ 2v_{\text{radial}}/\lambda 2 v radial ​ / λ describes a single moving reflector in a monostatic backscatter geometry. Separate transmitting and receiving stations require the rate of change of the total transmitter–scatterer–receiver path instead.

Caution

Recognising and Using Auroral Signals:

CW: Morse signals often sound like hiss or buzz instead of a clear tone. CW is usually the easiest mode to copy; use clear spacing and a speed appropriate to readability.

SSB: Speech can be raspy and difficult to understand, especially on 144 MHz 144\text{ MHz} 144 MHz , but useful SSB contacts are possible, particularly on 50 MHz 50\text{ MHz} 50 MHz . Speak slowly and clearly.

FM and narrow-shift data: Doppler spreading and rapid changes can make these modes difficult or unusable. Select the mode for the actual signal conditions rather than assuming all auroral paths have identical distortion.

Aspect Sensitivity and Antenna Heading

Strong coherent scatter requires a favourable orientation to the field-aligned irregularities. More precisely, the scattering vector —the difference between the outgoing and incident wave vectors—must be nearly perpendicular to the local magnetic field. For backscatter, this becomes the familiar near-perpendicular ray condition. It is not a universal 90 ∘ 90^\circ 9 0 ∘ angle between an individual incident ray and the field for every two-station path.

In Australia, search toward the southern auroral region and rotate the beam to peak the signal. Each station must illuminate a suitable common scattering volume , rather than simply point along the direct bearing to the other station. For a Melbourne–Adelaide contact, both beams may point broadly southward, but their optimum azimuths depend on the location of that volume and need not both be 180 ∘ 180^\circ 18 0 ∘ .

Trans-Equatorial Propagation (TEP)

Trans-equatorial propagation (TEP) supports long VHF paths across the geomagnetic equator. Two forms are important: afternoon TEP, chiefly on the lower VHF bands such as 50 MHz 50\text{ MHz} 50 MHz , and evening TEP, which can also support 144 MHz 144\text{ MHz} 144 MHz . They involve different features of the equatorial F F F region. Afternoon TEP: schematic FF chordal path

  • Southern anomaly crest Northern anomaly crest
  • *------------------------*
  • / ionospheric \
  • / segment \
  • / across the equator \
  • Transmitter Receiver
  • =====================================================
  • No intermediate ground reflection

This drawing represents the afternoon mechanism;

evening 144 MHz TEP involves spread-F irregularities.

The Appleton Anomaly and Equatorial Fountain

The equatorial ionisation anomaly , or Appleton anomaly, consists of enhanced F F F -region electron densities on either side of the magnetic equator, typically near ± 15 ∘ \pm15^\circ ± 1 5 ∘ magnetic latitude.

Solar EUV produces ionisation during the day.

A daytime eastward electric field, acting across the approximately horizontal northward magnetic field at the magnetic equator, causes an upward plasma drift: v ⃗ = E ⃗ × B ⃗ B 2 \vec{v}=\frac{\vec{E}\times\vec{B}}{B^2} v = B 2 E × B ​

Plasma lifted above the equator diffuses poleward and downward along magnetic field lines under gravity and pressure gradients. This fountain effect builds the two density crests. Their locations and densities vary with time, winds and electric fields; there is no fixed universal crest critical frequency.

The equatorial electrojet is an electric current associated with the equatorial electrodynamics, rather than the source that must first create the eastward field in this sequence.

Afternoon and Evening TEP

Afternoon TEP (a-TEP): Most often occurs around 1500 to 1900 1500\text{ to }1900 1500 to 1900 local time. The FF or chordal path refracts between the two anomaly crests before returning to Earth. It avoids an intermediate ground bounce and has fewer passages through the absorptive D D D region than a conventional two-hop F F F path. Oblique incidence and focusing help explain strong signals. Support is usually confined to lower VHF, roughly up to 60 MHz 60\text{ MHz} 60 MHz ; fading and distortion are generally limited, making SSB practical.

Evening TEP (e-TEP): Often occurs around 2000 to 2300 2000\text{ to }2300 2000 to 2300 local time and is associated with equatorial spread F . After sunset, instabilities can create field-aligned plasma bubbles, tubes or plumes with lower electron density than their surroundings. Refraction at these structures can guide signals through the ionosphere. This is the mechanism associated with many 144 MHz 144\text{ MHz} 144 MHz TEP contacts; 432 MHz 432\text{ MHz} 432 MHz support has been reported rarely. Deep, rapid fading and substantial Doppler spread can make speech difficult or unintelligible, so clear SSB is not guaranteed.

Favourable Paths and Conditions

TEP can span several thousand kilometres, including roughly 3000 to 8000 km 3000\text{ to }8000\text{ km} 3000 to 8000 km for evening paths. Stations approximately symmetric about the magnetic equator , on a roughly geomagnetic north–south circuit, have favourable geometry. Equinoxes and high solar activity favour occurrence; quiet geomagnetic conditions can also favour evening irregularities. These conditions improve the prospects of an opening but do not guarantee one.

Australia–Japan is an established TEP path. Monitor suitable beacons and actual band conditions before selecting frequency and mode. A reported 50 MHz 50\text{ MHz} 50 MHz afternoon opening does not establish that a 144 MHz 144\text{ MHz} 144 MHz evening path will be open or that SSB will be readable.

Comparison of Specialized VHF Ionospheric Modes

Parameter Sporadic-E ( E s E_s E s ​ ) Auroral Scatter Trans-Equatorial Propagation (TEP)

Ionospheric Layer & Altitude E E E region ( 95 − 115 km 95 - 115\text{ km} 95 − 115 km ) E E E region auroral oval ( 100 − 120 km 100 - 120\text{ km} 100 − 120 km ) F F F region: anomaly crests for a-TEP; spread-F irregularities for e-TEP

Physical Formation Mechanism Neutral wind shear compressing ablated metallic ions ( F e + , M g + Fe^+, Mg^+ F e + , M g + ) Energetic particle precipitation and field-aligned plasma irregularities a-TEP: crest-to-crest FF refraction; e-TEP: irregularity-guided paths

Usable Frequency Bands 28 MHz , 50 MHz 28\text{ MHz}, 50\text{ MHz} 28 MHz , 50 MHz ; rarely 144 MHz 144\text{ MHz} 144 MHz 50 MHz , 144 MHz 50\text{ MHz}, 144\text{ MHz} 50 MHz , 144 MHz ; rarely 432 MHz 432\text{ MHz} 432 MHz 50 MHz 50\text{ MHz} 50 MHz (a-TEP); 144 MHz 144\text{ MHz} 144 MHz (e-TEP)

Typical Path Distance Often 1000 − 2200 km 1000 - 2200\text{ km} 1000 − 2200 km (single hop); around 4000 km 4000\text{ km} 4000 km (double), conditions permitting 500 − 2000 km 500 - 2000\text{ km} 500 − 2000 km 4000 − 8000 km 4000 - 8000\text{ km} 4000 − 8000 km

Signal Strength & Distortion Can be strong; ionospheric loss, geometry and fading vary Weak to moderate, harsh raspy buzzing, severe Doppler spread Usually limited afternoon distortion; evening fading and distortion can be severe

Usable Modulation Modes All modes (SSB, CW, FM, FT8, Digital) CW usually easiest; distorted SSB can work, especially on 50 MHz SSB/CW on suitable a-TEP paths; e-TEP readability depends on Doppler spread and fading

Antenna Heading Requirement Directly toward target station Toward a common auroral scatter volume; peak the signal Roughly north-south across geomagnetic equator

Peak Seasonal Occurrence Mid-summer (Dec-Jan in VK); minor winter solstice peak Enhanced by geomagnetic storms; usable coverage depends on location Equinoctial months (March/Sept) during solar cycle maxima