Study guide

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction

ACMA Amateur Radio Advanced Recognition Certificate - Theory Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Theory, Circuit Laws & Passive Components

1.1 DC Circuit Analysis, Ohm's Law, and Kirchhoff's Laws 1.2 AC Fundamentals, Sine Waves, Peak, RMS, and Phase Relationships 1.3 Inductance, Capacitance, Reactance, and Time Constants

2 Chapter 2: Impedance, Resonance & Passive Filters

2.1 Complex Impedance, Phasors, and AC Circuit Analysis 2.2 Series and Parallel LC Resonance and Q Factor 2.3 Passive Filters, Cutoff Frequency, and Attenuator Pads

3 Chapter 3: Semiconductor Devices & Power Supplies

3.1 Semiconductor Diodes, Zener Regulators, and Rectifier Circuits 3.2 Bipolar Junction Transistors, FETs, and Operational Amplifiers 3.3 Thermionic Valves (Vacuum Tubes) and High-Power Linear Amplifiers 3.4 DC Power Supplies, Filter Networks, and Voltage Regulators

4 Chapter 4: Oscillators & Frequency Synthesis

4.1 RF Oscillators, LC Tank Topologies, and Frequency Stability 4.2 Phase-Locked Loops (PLLs) and Frequency Synthesisers 4.3 Direct Digital Synthesis (DDS), SDR Architectures, and Digital Filter Topologies

5 Chapter 5: RF Amplifiers & Linearity

5.1 Classes of Amplification, Conduction Angles, and Operating Efficiency 5.2 RF Power Amplifiers, Push-Pull Topologies, and Output Matching 5.3 Amplifier Stability, Neutralisation, and Intermodulation Distortion

6 Chapter 6: Modulation & Demodulation

6.1 Amplitude Modulation, Double Sideband, and Single Sideband (SSB) 6.2 Frequency Modulation, Phase Modulation, and FM Detectors 6.3 Digital Modulation Modes, Spectral Efficiency, and Weak-Signal Protocols

7 Chapter 7: Transmitters, Mixers & Receivers

7.1 RF Mixers, Frequency Translation, and Intermodulation 7.2 Transmitter Architectures, CW Keying, and Output Filtering 7.3 Superheterodyne Receiver Design, IF Selection, and Image Rejection 7.4 Receiver Performance Specifications, Dynamic Range, and Selectivity

8 Chapter 8: Transmission Lines & Waveguides

8.1 Transmission Line Characteristics, Impedance, and Velocity Factor 8.2 Standing Waves, Reflection Coefficient, SWR, and Return Loss 8.3 Resonant Line Sections, Quarter-Wave Transformers, and Stubs

9 Chapter 9: Impedance Matching & Baluns

9.1 Lumped-Element Matching Networks and Antenna Tuning Units 9.2 Baluns, Ununs, and Common-Mode Current Choking 9.3 Feedline Losses, High-SWR Stress, and Coaxial Installation Practice

10 Chapter 10: Practical Antennas & Arrays

10.1 Resonant Dipoles, Inverted-Vs, and Multiband Wire Antennas 10.2 Quarter-Wave Verticals, Ground Systems, and Radiation Efficiency 10.3 Parasitic Arrays, Yagi-Uda Antennas, and Quad Arrays 10.4 Antenna Gain, Aperture Antennas & Horns, ERP/EIRP, Radiation Patterns

11 Chapter 11: Radio Wave Propagation & Ionospheric Mechanics

11.1 Electromagnetic Wave Fundamentals, Polarisation, and Ground Waves 11.2 The Ionosphere, Solar Radiation, and Solar Cycles 11.3 Critical Frequency, Maximum Usable Frequency, and HF Propagation Paths

12 Chapter 12: VHF/UHF Propagation & Space Communications

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction 12.2 Sporadic-E, Auroral Scatter, and Trans-Equatorial Propagation 12.3 Amateur Satellites, Doppler Shift, and Earth-Moon-Earth (EME)

13 Chapter 13: Test Equipment & RF Measurements

13.1 Decibels, Power Ratios, and Cascaded Stage Calculations 13.2 RF Power Meters, Directional Couplers, and Dummy Loads 13.3 Multirange Meters, Waveform Diagnostics, Oscilloscopes, and Frequency Counters

14 Chapter 14: Advanced RF Analysis & Diagnostics

14.1 Spectrum Analyser Architecture, Operation, and Spectral Purity 14.2 Antenna Analysers, Vector Network Analysers, and Smith Charts 14.3 Calibrated Signal Generators, Grid Dip Meters, and Component Testing

15 Chapter 15: Electromagnetic Compatibility & Interference

15.1 Sources of Interference, Coupling Mechanisms, and Audio Rectification 15.2 Receiver Susceptibility, Desensitisation, and Front-End Intermodulation 15.3 Practical RFI Suppression, Filter Design, and Bonding Techniques

16 Chapter 16: Electrical, RF & Station Safety

16.1 Biological Effects of RF Energy and ARPANSA Exposure Standards 16.2 Safe Separation Distances, Power Density, and Duty Cycles 16.3 Station Electrical Safety, Battery Hazards, and Safe Headphone Use 16.4 Mast and Tower Construction, Power Line Clearance, and Lightning Protection

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction

Key Takeaways Explain This Topic AI

Under standard atmospheric conditions, vertical gradients of pressure, temperature, and water vapour produce a refractivity gradient of d N / d h ≈ − 39 N-units/km dN/dh \approx -39\text{ N-units/km} d N / d h ≈ − 39 N-units/km , bending radio waves downward toward Earth and establishing an effective Earth radius factor of k = 4 / 3 k = 4/3 k = 4/3 ( 8495 km 8495\text{ km} 8495 km ).

The radio horizon extends approximately 15.4 % 15.4\% 15.4% beyond the optical line of sight, with the total distance between two antennas calculated by d LOS ≈ 4.12 × ( h 1 + h 2 ) km d_{\text{LOS}} \approx 4.12 \times (\sqrt{h_1} + \sqrt{h_2})\text{ km} d LOS ​ ≈ 4.12 × ( h 1 ​ ​ + h 2 ​ ​ ) km when antenna heights are in metres.

Temperature inversions and rapid decreases of humidity with height can produce trapping gradients ( d N / d h < − 157 N-units/km dN/dh < -157\text{ N-units/km} d N / d h < − 157 N-units/km ). Duct depth, refractivity profile, frequency and antenna coupling determine whether a long VHF/UHF or microwave path is supported.

Obstacle clearance requires maintaining at least 60 % 60\% 60% clearance of the first Fresnel zone ( 0.6 R 1 0.6 R_1 0.6 R 1 ​ ) along the path to avoid diffraction losses; grazing clearance ( 0 R 1 0 R_1 0 R 1 ​ ) incurs a 6 dB 6\text{ dB} 6 dB knife-edge loss, while deeper shadowing induces severe attenuation.

Tropospheric scatter can support beyond-horizon paths of a few hundred kilometres, with continuously present but fading signals. Microwave rain scatter uses a precipitation volume visible to both stations; Doppler spreading can give CW and SSB a raspy sound.

Last updated: November 2026

12.1 Line-of-Sight, Tropospheric Ducting, and Diffraction

At high frequencies (HF, 3 to 30 MHz 3\text{ to }30\text{ MHz} 3 to 30 MHz ), radio waves rely extensively on ionospheric refraction to travel thousands of kilometres beyond the curvature of the Earth. However, as operating frequencies transition into the Very High Frequency (VHF, 30 to 300 MHz 30\text{ to }300\text{ MHz} 30 to 300 MHz ), Ultra High Frequency (UHF, 300 to 3000 MHz 300\text{ to }3000\text{ MHz} 300 to 3000 MHz ), and Super High Frequency (SHF / microwave, 3 to 30 GHz 3\text{ to }30\text{ GHz} 3 to 30 GHz ) regimes, electromagnetic waves routinely penetrate the normal ionospheric layers ( D D D , E E E , and F F F ) without sufficient refraction to return to ground. Consequently, terrestrial communication at VHF and UHF depends predominantly on propagation through the lowest layer of Earth's atmosphere: the troposphere .

While VHF and UHF transmissions are broadly characterized as "line-of-sight" (LOS) modes, the physical trajectory of a radio wave in the atmosphere is rarely a straight geometric line. Variations in atmospheric temperature, barometric pressure, and water vapour pressure bend, guide, scatter, and diffract electromagnetic energy, establishing communication paths that extend well beyond the visual horizon.

Atmospheric Refraction and the Radio Horizon

The troposphere extends from the Earth's surface to an altitude of roughly 10 to 12 km 10\text{ to }12\text{ km} 10 to 12 km at temperate latitudes. The propagation velocity ( v v v ) of an electromagnetic wave through air is governed by the atmospheric refractive index ( n n n ): v = c n v = \frac{c}{n} v = n c ​

where c ≈ 2.9979 × 10 8 m/s c \approx 2.9979 \times 10^8\text{ m/s} c ≈ 2.9979 × 1 0 8 m/s is the speed of light in vacuum. In air, n n n exceeds unity by only a tiny fraction (typically n ≈ 1.0003 n \approx 1.0003 n ≈ 1.0003 at sea level). To handle these microscopic differences conveniently, atmospheric scientists define radio refractivity ( N N N ) in dimensionless " N N N -units": N = ( n − 1 ) × 10 6 N = (n - 1) \times 10^6 N = ( n − 1 ) × 1 0 6

Empirically, atmospheric refractivity depends on three thermodynamic variables: N = 77.6 T ( P + 4810 e T ) N = \frac{77.6}{T} \left( P + \frac{4810 e}{T} \right) N = T 77.6 ​ ( P + T 4810 e ​ )

where:

  • P P P is total atmospheric barometric pressure in hectopascals (hPa or mbar),
  • T T T is absolute temperature in Kelvin (K),
  • e e e is the partial pressure of water vapour in hectopascals (hPa). Wavefront Bending in the Troposphere
  • Higher Altitude: Lower n -> Faster Wavefront (v_top)
  • --------------------->
  • / /
  • / /
  • / / Wavefront tilts downward
  • / / toward Earth's surface
  • ---------------------->
  • Lower Altitude: Higher n -> Slower Wavefront (v_bottom)
  • =======================================================
  • Earth's Surface
  • The Standard Refractivity Gradient and the 4/3 Earth Radius

In a well-mixed, "standard" atmosphere, atmospheric pressure and moisture content decrease exponentially with altitude, while temperature drops at an average environmental lapse rate of approximately 6.5 ∘ C 6.5^\circ\text{C} 6. 5 ∘ C per kilometre ( 6.5 K/km 6.5\text{ K/km} 6.5 K/km ). As a result of this vertical structure, refractivity decreases steadily with height above ground level ( h h h ): d N d h ≈ − 39 N-units/km ( or d n d h ≈ − 39 × 10 − 9 m − 1 ) \frac{dN}{dh} \approx -39\text{ N-units/km} \quad \left(\text{or } \frac{dn}{dh} \approx -39 \times 10^{-9}\text{ m}^{-1}\right) d h d N ​ ≈ − 39 N-units/km ( or d h d n ​ ≈ − 39 × 1 0 − 9 m − 1 )

Because the refractive index decreases with altitude, the upper portion of an advancing electromagnetic wavefront travels slightly faster than the lower portion ( v top > v bottom v_{\text{top}} > v_{\text{bottom}} v top ​ > v bottom ​ ). This velocity differential causes the wave to continuously tilt downward toward the Earth's surface. The radius of curvature ( r r r ) of the refracted ray path is: 1 r = − d n d h ≈ 39 × 10 − 9 m − 1 ⟹ r ≈ 25 , 600 km \frac{1}{r} = -\frac{dn}{dh} \approx 39 \times 10^{-9}\text{ m}^{-1} \implies r \approx 25,600\text{ km} r 1 ​ = − d h d n ​ ≈ 39 × 1 0 − 9 m − 1 ⟹ r ≈ 25 , 600 km

Because this downward ray curvature ( r ≈ 25 , 600 km r \approx 25,600\text{ km} r ≈ 25 , 600 km ) is less than the physical curvature of the Earth ( a ≈ 6371 km a \approx 6371\text{ km} a ≈ 6371 km ), the wave does not follow the planet indefinitely, but it bends around the curve far more than a straight optical ray.

To simplify RF link planning, engineers replace the curved ray path over a curved Earth with an equivalent straight-line ray propagating over a fictitious, enlarged Earth of effective radius ( a e = k a a_e = k a a e ​ = ka ). The effective Earth radius factor ( k k k ) is given by: k = 1 1 + a d n d h = 1 1 − 6371 × 10 3 × 39 × 10 − 9 ≈ 1 1 − 0.2485 ≈ 4 3 ≈ 1.333 k = \frac{1}{1 + a \frac{dn}{dh}} = \frac{1}{1 - 6371 \times 10^3 \times 39 \times 10^{-9}} \approx \frac{1}{1 - 0.2485} \approx \frac{4}{3} \approx 1.333 k = 1 + a d h d n ​ 1 ​ = 1 − 6371 × 1 0 3 × 39 × 1 0 − 9 1 ​ ≈ 1 − 0.2485 1 ​ ≈ 3 4 ​ ≈ 1.333

Important

Under standard atmospheric conditions, the effective Earth radius factor is k = 4 / 3 k = 4/3 k = 4/3 . The effective Earth radius is: a e = 4 3 × 6371 km ≈ 8495 km a_e = \frac{4}{3} \times 6371\text{ km} \approx 8495\text{ km} a e ​ = 3 4 ​ × 6371 km ≈ 8495 km

This downward refraction allows VHF and UHF radio signals to propagate beyond the geometric optical horizon.

Derivation of the Radio Horizon Formula

From the geometry of a sphere of effective radius a e a_e a e ​ , the distance ( d d d ) from an antenna at height h h h above flat ground to the tangential horizon point is given by the Pythagorean theorem: ( a e + h ) 2 = a e 2 + d 2 ⟹ a e 2 + 2 a e h + h 2 = a e 2 + d 2 (a_e + h)^2 = a_e^2 + d^2 \implies a_e^2 + 2 a_e h + h^2 = a_e^2 + d^2 ( a e ​ + h ) 2 = a e 2 ​ + d 2 ⟹ a e 2 ​ + 2 a e ​ h + h 2 = a e 2 ​ + d 2

Since the antenna height h h h is negligible compared to the planetary radius ( h ≪ a e h \ll a_e h ≪ a e ​ ), the h 2 h^2 h 2 term can be omitted: d ≈ 2 a e h d \approx \sqrt{2 a_e h} d ≈ 2 a e ​ h ​

For the visual (optical) horizon over true Earth ( a = 6371 km a = 6371\text{ km} a = 6371 km , where h h h is in metres and d d d is in kilometres): d optical ≈ 2 × 6371 × 10 − 3 × h ≈ 3.57 h (km) d_{\text{optical}} \approx \sqrt{2 \times 6371 \times 10^{-3} \times h} \approx 3.57 \sqrt{h}\text{ (km)} d optical ​ ≈ 2 × 6371 × 1 0 − 3 × h ​ ≈ 3.57 h ​ (km)

For the radio horizon under standard k = 4 / 3 k = 4/3 k = 4/3 atmospheric refraction ( a e = 8495 km a_e = 8495\text{ km} a e ​ = 8495 km ): d radio ≈ 2 × 8495 × 10 − 3 × h = 16.99 h ≈ 4.12 h (km) d_{\text{radio}} \approx \sqrt{2 \times 8495 \times 10^{-3} \times h} = \sqrt{16.99 h} \approx 4.12 \sqrt{h}\text{ (km)} d radio ​ ≈ 2 × 8495 × 1 0 − 3 × h ​ = 16.99 h ​ ≈ 4.12 h ​ (km)

When two stations at antenna heights h 1 h_1 h 1 ​ and h 2 h_2 h 2 ​ (metres above ground level) establish a line-of-sight path over smooth terrain, the maximum unobstructed radio path length ( d LOS d_{\text{LOS}} d LOS ​ ) is the sum of their individual horizon distances: d LOS = d 1 + d 2 ≈ 4.12 × ( h 1 + h 2 ) km d_{\text{LOS}} = d_1 + d_2 \approx 4.12 \times \left(\sqrt{h_1} + \sqrt{h_2}\right)\text{ km} d LOS ​ = d 1 ​ + d 2 ​ ≈ 4.12 × ( h 1 ​ ​ + h 2 ​ ​ ) km

Comparing the two multipliers ( 4.12 / 3.57 ≈ 1.154 4.12 / 3.57 \approx 1.154 4.12/3.57 ≈ 1.154 ), standard atmospheric refraction extends the radio horizon approximately 15.4 % 15.4\% 15.4% beyond the optical horizon .

Step-by-Step Worked Example: Repeater Line-of-Sight Distance

An amateur radio club installs a 147 MHz 147\text{ MHz} 147 MHz 2-meter VHF repeater on a hilltop mast with an antenna height of h 1 = 64 metres h_1 = 64\text{ metres} h 1 ​ = 64 metres above surrounding terrain. A mobile operator uses a quarter-wave whip antenna mounted on a vehicle roof at h 2 = 2.25 metres h_2 = 2.25\text{ metres} h 2 ​ = 2.25 metres . Calculate:

The optical horizon distance between the two antennas.

The radio horizon distance under standard k = 4 / 3 k=4/3 k = 4/3 atmospheric refraction.

The additional communication distance gained purely from tropospheric refraction.

Step 1: Calculate the optical horizon distance: d optical = 3.57 × ( 64 + 2.25 ) = 3.57 × ( 8.0 + 1.5 ) = 3.57 × 9.5 ≈ 33.92 km d_{\text{optical}} = 3.57 \times (\sqrt{64} + \sqrt{2.25}) = 3.57 \times (8.0 + 1.5) = 3.57 \times 9.5 \approx 33.92\text{ km} d optical ​ = 3.57 × ( 64 ​ + 2.25 ​ ) = 3.57 × ( 8.0 + 1.5 ) = 3.57 × 9.5 ≈ 33.92 km

Step 2: Calculate the radio horizon distance: d radio = 4.12 × ( 64 + 2.25 ) = 4.12 × ( 8.0 + 1.5 ) = 4.12 × 9.5 ≈ 39.14 km d_{\text{radio}} = 4.12 \times (\sqrt{64} + \sqrt{2.25}) = 4.12 \times (8.0 + 1.5) = 4.12 \times 9.5 \approx 39.14\text{ km} d radio ​ = 4.12 × ( 64 ​ + 2.25 ​ ) = 4.12 × ( 8.0 + 1.5 ) = 4.12 × 9.5 ≈ 39.14 km

Step 3: Calculate the distance gained: Δ d = d radio − d optical = 39.14 km − 33.92 km = 5.22 km \Delta d = d_{\text{radio}} - d_{\text{optical}} = 39.14\text{ km} - 33.92\text{ km} = 5.22\text{ km} Δ d = d radio ​ − d optical ​ = 39.14 km − 33.92 km = 5.22 km

Standard atmospheric refraction extends the reliable direct coverage footprint by more than 5.2 km 5.2\text{ km} 5.2 km in radius.

Tropospheric Ducting and Super-Refraction

Under non-standard weather conditions, the vertical profile of temperature, pressure, and humidity departs drastically from the standard lapse rate. These deviations alter the refractivity gradient ( d N / d h dN/dh d N / d h ), leading to four distinct refractive regimes:

Sub-refraction ( d N / d h > − 39 N-units/km dN/dh > -39\text{ N-units/km} d N / d h > − 39 N-units/km , relative to this standard model): Downward bending is weaker than normal. At d N / d h = 0 dN/dh=0 d N / d h = 0 rays are straight; a positive gradient bends them upward. The radio horizon is shorter than in the standard atmosphere.

Standard Refraction ( d N / d h ≈ − 39 N-units/km dN/dh \approx -39\text{ N-units/km} d N / d h ≈ − 39 N-units/km ): Normal downward bending with k = 4 / 3 k = 4/3 k = 4/3 .

Super-refraction ( − 157 < d N / d h < − 39 N-units/km -157 < dN/dh < -39\text{ N-units/km} − 157 < d N / d h < − 39 N-units/km ): Downward curvature is more pronounced than normal ( k > 4 / 3 k > 4/3 k > 4/3 ), extending the radio horizon significantly.

Trapping or Ducting ( d N / d h < − 157 N-units/km dN/dh < -157\text{ N-units/km} d N / d h < − 157 N-units/km ): The downward radius of curvature of the wave becomes smaller than the radius of the Earth ( r < a r < a r < a ). The effective Earth radius factor k k k becomes negative or infinite. The radio wave is trapped between atmospheric boundaries or between an atmospheric boundary and the ground. Surface duct: schematic ray paths

  • Strong fall of refractivity with height
  • ---------------------------------------
  • __ __ __
  • __/ \______/ \______/ \___ guided rays
  • ========================================
  • Sea / ground

Rays curve within the refractive layer;

confinement depends on frequency and launch angle.

Physical Mechanisms of Duct Formation

For trapping to occur ( d N / d h < − 157 N-units/km dN/dh < -157\text{ N-units/km} d N / d h < − 157 N-units/km ), the term ( P + 4810 e / T ) (P + 4810e/T) ( P + 4810 e / T ) in the refractivity equation must decrease extremely rapidly with altitude. This is driven by two meteorological conditions acting individually or together:

Temperature Inversion: Temperature increases with altitude ( d T / d h > 0 dT/dh > 0 d T / d h > 0 ) rather than dropping, causing warm dry air to sit directly above cooler air.

Steep Water Vapour Gradient: The humidity drops precipitously with altitude ( d e / d h ≪ 0 de/dh \ll 0 d e / d h ≪ 0 ), such as directly above an ocean surface where a thin, saturated layer is capped by bone-dry continental air.

Three primary meteorological scenarios trigger ducting:

Nocturnal Radiation Cooling: On clear, windless nights, the Earth's surface radiates heat rapidly into space, chilling the ground and the immediate surface air layer. Warmer air remains aloft, creating a shallow ground-based temperature inversion that forms after dusk and dissipates shortly after sunrise.

High-Pressure Anticyclonic Subsidence: Large, slow-moving high-pressure systems feature descending air that warms adiabatically as it compresses. This creates an elevated subsidence inversion layer between 500 and 2000 metres 500\text{ and }2000\text{ metres} 500 and 2000 metres altitude, capable of forming vast elevated ducts spanning thousands of kilometres.

Coastal Advection: Warm, dry air from hot desert or continental interiors blows out over cold ocean waters. The cold sea chills the lowest layer of air while evaporation charges it with moisture, establishing a permanent or semi-permanent maritime surface duct.

Spreading and Range Extension

In free space, power density from a given transmitter decreases as 1 / d 2 1/d^2 1/ d 2 , corresponding to a 20 dB 20\text{ dB} 20 dB increase in spreading loss per decade of distance.

An ideal duct that confines energy vertically can approach cylindrical spreading, with power density varying as 1 / d 1/d 1/ d and spreading loss increasing by 10 dB 10\text{ dB} 10 dB per decade. This illustrates why ducting can greatly enhance distant signals. A real atmospheric duct also leaks energy and has surface, absorption and coupling losses; its total path loss is not fixed by this ideal spreading law. Long maritime paths can open with modest stations, but transmitter power alone cannot predict received signal strength.

Frequency Limits and Duct Depth

An atmospheric duct resembles a waveguide, but its boundaries are refractive gradients rather than metal walls. Its ability to confine a wavelength depends on both its depth and the strength and shape of its refractivity profile. There is no universal depth threshold for each amateur band, and the transition to poorly confined propagation is gradual.

A deeper or stronger duct can confine longer wavelengths than a shallow, weak duct.

Shallow maritime ducts often favour UHF and microwave propagation.

Antenna height and elevation angle determine how effectively a station couples energy into the duct.

Tip

Check other VHF/UHF bands during an opening, but assess each band separately. A strong 144 MHz 144\text{ MHz} 144 MHz path does not guarantee a stronger 432 MHz 432\text{ MHz} 432 MHz or 1.2 GHz 1.2\text{ GHz} 1.2 GHz signal.

Southern Australian Maritime Paths

The Great Australian Bight and Bass Strait provide useful examples of over-water paths on which inversions and humidity gradients can enhance VHF/UHF communication. Openings depend on the position and continuity of the refractive layer, antenna coupling and the station link budget. Listen for distant beacons and compare bands rather than assuming a particular range or signal strength from the weather chart alone.

Terrain Diffraction and Obstacle Clearance

When a radio wave encounters terrain, diffraction carries some energy into the geometric shadow. The Huygens-Fresnel principle describes this through contributions from the unobstructed wavefront. A sharp isolated ridge can be approximated by a knife edge . Rounded hills, multiple obstacles and the curved Earth require other diffraction models. Single knife-edge geometry

  • summit
  • o
  • /|\
  • / |h\
  • Tx o---------------+---------------o Rx
  • <--- d1 ---> <--- d2 --->
  • <--------- D=d1+d2 -------->

h is positive above the direct Tx-Rx ray;

it is negative when the summit is below it.

The Knife-Edge Diffraction Parameter

The attenuation caused by an obstacle depends on the dimensionless Fresnel-Kirchhoff diffraction parameter ( ν \nu ν ): ν = h 2 ( d 1 + d 2 ) λ d 1 d 2 = h 2 D λ d 1 d 2 \nu = h \sqrt{\frac{2 (d_1 + d_2)}{\lambda d_1 d_2}} = h \sqrt{\frac{2 D}{\lambda d_1 d_2}} ν = h λ d 1 ​ d 2 ​ 2 ( d 1 ​ + d 2 ​ ) ​ ​ = h λ d 1 ​ d 2 ​ 2 D ​ ​

where:

h h h is the clearance height of the obstacle apex above the direct line-of-sight ray path (defined as positive if the obstacle penetrates above the ray line, and negative if the apex is below the line),

  • d 1 d_1 d 1 ​ is the distance from the transmitter to the obstacle,
  • d 2 d_2 d 2 ​ is the distance from the obstacle to the receiver,
  • D = d 1 + d 2 D = d_1 + d_2 D = d 1 ​ + d 2 ​ is the total path length,

λ \lambda λ is the radio wavelength.

When the obstacle apex lies precisely on the line-of-sight path between the two antennas ( h = 0 h = 0 h = 0 , grazing incidence): ν = 0 ⟹ Diffraction loss is exactly 6.0 dB \nu = 0 \implies \text{Diffraction loss is exactly } 6.0\text{ dB} ν = 0 ⟹ Diffraction loss is exactly 6.0 dB

A grazing obstruction blocks half of the first Fresnel zone's electric field, halving the received voltage ( V / V 0 = 0.5 V / V_0 = 0.5 V / V 0 ​ = 0.5 ) and quartering the power, which corresponds to an unavoidable 6 dB 6\text{ dB} 6 dB obstacle loss.

Fresnel Zones and Clearance Criteria

To ensure that an RF path achieves free-space propagation without diffraction attenuation, the line of sight must not merely clear the geometric crest of intervening terrain—it must maintain adequate clearance across its Fresnel zones .

Fresnel zones are concentric, football-shaped (prolate spheroidal) boundaries surrounding the direct ray path. The n n n -th Fresnel zone boundary represents the locus of points where an indirect wave reflected from the boundary travels a distance that is n n n half-wavelengths ( n λ / 2 n \lambda / 2 nλ /2 ) longer than the direct ray: Δ d = d indirect − d direct = n λ 2 \Delta d = d_{\text{indirect}} - d_{\text{direct}} = n \frac{\lambda}{2} Δ d = d indirect ​ − d direct ​ = n 2 λ ​

For the crucial First Fresnel Zone ( n = 1 n = 1 n = 1 ) , the path length difference is λ / 2 \lambda / 2 λ /2 ( 180 ∘ 180^\circ 18 0 ∘ phase shift). The radius of the first Fresnel zone ( R 1 R_1 R 1 ​ ) at any point along the link is: R 1 = λ d 1 d 2 d 1 + d 2 = 17.32 d 1 d 2 f GHz D km (metres) R_1 = \sqrt{\frac{\lambda d_1 d_2}{d_1 + d_2}} = 17.32 \sqrt{\frac{d_1 d_2}{f_{\text{GHz}} D_{\text{km}}}}\text{ (metres)} R 1 ​ = d 1 ​ + d 2 ​ λ d 1 ​ d 2 ​ ​ ​ = 17.32 f GHz ​ D km ​ d 1 ​ d 2 ​ ​ ​ (metres)

where d 1 , d 2 , d_1, d_2, d 1 ​ , d 2 ​ , and D D D are in kilometres, and f GHz f_{\text{GHz}} f GHz ​ is the carrier frequency in GHz.

Important

The 60% Clearance Rule: To avoid diffraction loss, an RF link must maintain a clearance of at least 60 % 60\% 60% of the first Fresnel zone radius ( 0.6 R 1 0.6 R_1 0.6 R 1 ​ ) above all terrain, buildings, and tree lines along the entire path. At 0.6 R 1 0.6 R_1 0.6 R 1 ​ clearance, diffraction loss drops to approximately 0 dB 0\text{ dB} 0 dB . If clearance drops to 0 R 1 0 R_1 0 R 1 ​ (grazing), loss is 6 dB 6\text{ dB} 6 dB ; if terrain intrudes further, loss escalates rapidly to 15 − 30 dB 15 - 30\text{ dB} 15 − 30 dB .

Step-by-Step Worked Example: First Fresnel Zone Radius Calculation

An amateur radio operator designs a 24 km 24\text{ km} 24 km point-to-point link on the 1.296 GHz 1.296\text{ GHz} 1.296 GHz ( 23 cm 23\text{ cm} 23 cm ) band. A sharp mountain ridge crosses the path at a distance of d 1 = 8 km d_1 = 8\text{ km} d 1 ​ = 8 km from the transmitter and d 2 = 16 km d_2 = 16\text{ km} d 2 ​ = 16 km from the receiver ( D = 24 km D = 24\text{ km} D = 24 km ). Calculate:

The radius of the first Fresnel zone ( R 1 R_1 R 1 ​ ) at the mountain ridge.

The minimum vertical clearance required above the ridge crest to eliminate diffraction loss.

Step 1: Calculate R 1 R_1 R 1 ​ using the formula: R 1 = 17.32 d 1 d 2 f GHz D km = 17.32 8 × 16 1.296 × 24 = 17.32 128 31.104 R_1 = 17.32 \sqrt{\frac{d_1 d_2}{f_{\text{GHz}} D_{\text{km}}}} = 17.32 \sqrt{\frac{8 \times 16}{1.296 \times 24}} = 17.32 \sqrt{\frac{128}{31.104}} R 1 ​ = 17.32 f GHz ​ D km ​ d 1 ​ d 2 ​ ​ ​ = 17.32 1.296 × 24 8 × 16 ​ ​ = 17.32 31.104 128 ​ ​ R 1 = 17.32 4.1152 = 17.32 × 2.0286 ≈ 35.14 metres R_1 = 17.32 \sqrt{4.1152} = 17.32 \times 2.0286 \approx 35.14\text{ metres} R 1 ​ = 17.32 4.1152 ​ = 17.32 × 2.0286 ≈ 35.14 metres

Step 2: Calculate the required 60 % 60\% 60% clearance: Clearance = 0.60 × R 1 = 0.60 × 35.14 m ≈ 21.08 metres \text{Clearance} = 0.60 \times R_1 = 0.60 \times 35.14\text{ m} \approx 21.08\text{ metres} Clearance = 0.60 × R 1 ​ = 0.60 × 35.14 m ≈ 21.08 metres

The direct visual line between the two antennas must pass at least 21.1 metres 21.1\text{ metres} 21.1 metres above the summit of the mountain ridge to prevent diffraction loss.

Rain Scatter and Tropospheric Scatter

Beyond direct line of sight and ducting, scattering can provide additional paths. Their usefulness depends on the scattering volume, station equipment and fading.

1. Rain Scatter (Precipitation Scatter)

Rain scatter is useful on microwave bands, especially 5.7 GHz 5.7\text{ GHz} 5.7 GHz and 10 GHz 10\text{ GHz} 10 GHz , and is also possible at 24 GHz 24\text{ GHz} 24 GHz . At 10 GHz 10\text{ GHz} 10 GHz the wavelength is about 30 mm 30\text{ mm} 30 mm , larger than typical millimetre-sized raindrops. Scattering increases strongly with frequency in the Rayleigh region; at higher frequencies particle size and additional attenuation become increasingly important.

Operating Technique: Stations do not point their dish or horn antennas toward each other. Instead, both operators aim their narrow antenna beams toward a common intense rain cell or thunderstorm located within their mutual line of sight, often 100 to 400 km 100\text{ to }400\text{ km} 100 to 400 km away.

Doppler Broadening: Raindrops within a storm cell fall at differing terminal velocities and are buffeted by turbulent convective updrafts and downdrafts moving at 10 to 30 m/s 10\text{ to }30\text{ m/s} 10 to 30 m/s . The reflections off these randomly moving droplets impose extreme Doppler broadening ( 100 to 500 Hz 100\text{ to }500\text{ Hz} 100 to 500 Hz ) on the scattered signal.

Audio Effect: CW and SSB can acquire a raspy sound from Doppler spreading. CW is often easier to copy, and strong signals can support narrowband FM. Digital decoding depends on the mode’s tolerance of the spread and fading; readability is not guaranteed.

2. Tropospheric Scatter (Tropo-scatter)

Small irregularities in tropospheric refractive index scatter a small part of the transmitted energy forward. Both stations aim directional antennas toward a common volume beyond their horizons. The additional loss depends on frequency, scattering angle, refractivity and antenna coupling.

Availability: The mechanism is continuously present, unlike an occasional duct opening. Received signals still undergo slow atmospheric variations and rapid fading, so continuous readability requires adequate link margin.

Range: Paths of a few hundred kilometres, for example 200 to 600 km 200\text{ to }600\text{ km} 200 to 600 km , are useful illustrations. Terrain shielding, antenna horizon angles and the link budget determine whether a particular path works.

Equipment: Directional antennas, low feeder loss, low receiver noise and narrowband modes such as CW or Q65 improve the link budget. Use sufficient lawful power: in the relevant Advanced bands the class licence permits 400 W 400\text{ W} 400 W pX for C3F/J3E/R3E and 120 W 120\text{ W} 120 W mean power for other emissions, including CW and Q65.

Propagation Mode Comparison

Propagation Mode Operational Frequency Range Typical Practical Distance Primary Physical Mechanism Signal Characteristics Atmospheric / Weather Dependence

Standard Line-of-Sight VHF, UHF, Microwave ( 30 MHz − 24 GHz 30\text{ MHz} - 24\text{ GHz} 30 MHz − 24 GHz ) 30 − 100 km 30 - 100\text{ km} 30 − 100 km k = 4 / 3 k=4/3 k = 4/3 standard downward atmospheric refraction Steady, clear, stable amplitude Normal atmosphere ( d N / d h ≈ − 39 N/km dN/dh \approx -39\text{ N/km} d N / d h ≈ − 39 N/km )

Tropospheric Ducting VHF, UHF and microwave; depends on the duct Hundreds to thousands of kilometres during openings Trapping in a sufficiently deep layer with d N / d h < − 157 N/km dN/dh < -157\text{ N/km} d N / d h < − 157 N/km Can be strong, with slow fading; no fixed signal level Inversions and humidity gradients; path continuity and antenna coupling matter

Terrain Diffraction VHF, UHF and microwave Depends on obstacle and path geometry Wave energy reaches the shadow; a sharp isolated ridge is modelled as a knife edge Loss depends on clearance, wavelength and terrain shape Refraction changes effective clearance; about 0.6 R 1 0.6R_1 0.6 R 1 ​ clearance is the usual negligible-loss planning rule

Tropospheric Scatter VHF, UHF and microwave Commonly a few hundred kilometres Forward scatter from refractive-index irregularities in a shared volume Weak signals with rapid fading and slower atmospheric changes Mechanism continuously present; loss and availability vary with atmospheric conditions

Rain Scatter Especially 5.7 GHz 5.7\text{ GHz} 5.7 GHz and 10 GHz 10\text{ GHz} 10 GHz ; also 24 GHz 24\text{ GHz} 24 GHz A few kilometres to several hundred, depending on scatter volume Scattering from precipitation in both antenna beams Often raspy CW/SSB from Doppler spreading; mode and strength determine readability Requires a suitable precipitation volume visible to both stations