Study guide

6.1 Pre-Departure Daily Safety Inspections

NSW Heavy Vehicle Knowledge Test Exam

Track your progress as you read

Finished sections get a check mark.

1 NSW Heavy Vehicle Licensing, Qualifications & Pathways

1.1 Heavy Vehicle Licence Classes and Progression Pathways 1.2 Transmission Restrictions, Assessments, and Driver Qualifications 1.3 HVKT Test Structure, Delivery, and Exam Day Logistics

2 Driver Health, Alcohol and Drugs, and Roadside Testing

2.1 Alcohol Limits, Breath Testing and Drink-Driving Sanctions 2.2 Roadside Drug Testing and Prescribed Medications 2.3 Driver Health, Medical Conditions, and Commercial Fitness Standards

3 Fatigue Management, Heavy Vehicle National Law, and Work Diaries

3.1 Fatigue Science, Warning Signs, and Risk Factors 3.2 Standard Hours Work and Rest Limits 3.3 Basic Fatigue Management (BFM) and Advanced Fatigue Management (AFM) 3.4 National Driver Work Diary Rules and Record-Keeping

4 Low-Risk Driving, Spatial Management, and Maneuvering

4.1 Crash Avoidance Space, Scanning, and Following Distances 4.2 Speed Management, Braking Distances, and Rollover Prevention 4.3 Off-Tracking, Turning Sweeps, and Safe Reversing

5 NSW Heavy Vehicle Road Rules, Signs, and Infrastructure

5.1 "Do Not Overtake Turning Vehicle" Rules and Multi-Lane Turns 5.2 Heavy Vehicle Road Signs, Lane Restrictions, and Low Gear Descents 5.3 Level Crossings, Portable Warning Triangles, and Heavy Vehicle Parking

6 Vehicle Roadworthiness, Inspections, and Braking Systems

6.1 Pre-Departure Daily Safety Inspections 6.2 Air Brake Systems, Pressures, and Low-Air Warnings 6.3 Brake Fade, Auxiliary Retarders, and Non-Synchromesh Transmissions 6.4 Heavy Vehicle Defect Notices and Compliance Inspections

7 Vehicle Mass, Dimension Limits, and General vs Restricted Access

7.1 Statutory Mass Limits and Axle Weight Distribution 7.2 Statutory Dimension Limits and Overhang Regulations 7.3 Restricted Access Vehicles (RAVs), PBS, and Oversize/Overmass Permits

8 Combination Vehicles, Coupling, and Load Restraint

8.1 Coupling and Uncoupling Procedures for Combination Vehicles 8.2 Combination Vehicle Dynamics, Air Lines, and Roll-Away Prevention 8.3 National Load Restraint Guide Standards and Restraint Methods

9 NSW Road Rules: Signs, Signals and Lane Discipline

9.1 Traffic Signs: Regulatory, Warning and Heavy-Vehicle Signs 9.2 Traffic Lights, Arrows and Lane Discipline 9.3 Intersections, Give Way, Stop Signs and Roundabouts

10 Sharing the Road with Vulnerable Road Users

10.1 Pedestrians, Children, School and Rail Crossings 10.2 Bicycle Riders, Motorcyclists, Horses and Sharing the Road 10.3 Seat Belts, Restraints and Getting In and Out Safely

11 Offences, Enforcement and Test Integrity

11.1 Negligent and Dangerous Driving, Overtaking and Road Works 11.2 Speed Limits, Speed Limiters and Speeding Penalties 11.3 Vehicle Monitors, Noise, Emissions and Test Integrity

6.1 Pre-Departure Daily Safety Inspections

Key Takeaways Explain This Topic AI

The pre-departure daily safety check is a mandatory 360-degree walkaround inspection covering tyres, wheels, suspension, steering, fluids, lights, glass, load security, and couplings before moving the vehicle.

The legal minimum tyre tread depth across Australia is 1.5 mm across the entire breadth of the tread and around the complete circumference; dual tyre sets must maintain adequate clearance and be free of trapped stones.

Wheel security checks require visual inspection for rust streaks radiating from studs (indicating loose nuts), missing or cracked wheel nuts, and fatigue cracks in the rim radiating from stud holes.

Fluid level checks must verify engine oil, engine coolant, power steering fluid, clutch/brake fluid reservoirs, and windscreen washer fluid levels before engine startup.

Daily pre-trip inspection results, identified defects, and rectification actions must be formally documented in an approved pre-trip inspection log or electronic fleet management application under Chain of Responsibility requirements.

Last updated: August 2026

Pre-Departure Daily Safety Inspections

Key Focus: Operating a heavy vehicle on NSW public roads requires the driver to conduct a comprehensive 360-degree walkaround inspection before commencing the first journey of the day. A vehicle must never enter traffic with safety-critical defects such as under-inflated tyres, loose wheel nuts, fluid leaks, or compromised coupling mechanisms.

Under the Heavy Vehicle National Law (HVNL) and Transport for NSW (TfNSW) road safety standards, professional heavy vehicle drivers bear primary responsibility for verifying that their vehicle and any attached trailers are completely roadworthy prior to departure. A structured pre-trip inspection prevents catastrophic mechanical failures, reduces roadside breakdown delays, and forms a critical element of compliance under national Chain of Responsibility (CoR) legislation.

The 360-Degree Pre-Trip Walkaround Workflow

A disciplined pre-departure inspection follows a consistent, circular route around the heavy vehicle combination. Drivers should establish a clockwise or counter-clockwise routine to ensure no component is overlooked. [Cabin Entry / Documentation] ──► [Front of Vehicle / Steering Axle]

  • ▲ │
  • │ ▼
  • [Cabin Controls & Brake Leak Check] [Left (Passenger) Side & Tyres]
  • ▲ │
  • │ ▼
  • [Right (Driver) Side & Fuel Tanks] ◄── [Rear of Vehicle & Trailer Couplings]
  • 1. Approach & Initial Observation

Check vehicle stance on level ground for abnormal body tilt or suspension sagging (indicating a broken spring leaf or ruptured air spring airbag).

Inspect the ground underneath the engine, transmission, and drive axles for fresh puddles of engine oil, coolant, fuel, or hydraulic/brake fluid.

2. Under-Bonnet & Fluid Level Verifications

Before starting the engine, open the bonnet or tilt the cab to inspect vital mechanical fluids:

Engine Oil: Verify oil level on the dipstick falls between the ADD and FULL marks.

Coolant Reservoir: Confirm coolant level in the translucent header tank; never remove a radiator pressure cap from a hot engine.

Power Steering Fluid: Check the reservoir dipstick/sight glass for correct operating level.

Clutch / Hydraulic Brake Fluid: Inspect master cylinder reservoirs for leaks and proper fluid height.

Windscreen Washer Reservoir: Top up washer fluid with clean water and approved detergent.

Accessory Belts & Hoses: Inspect serpentine and V-belts for correct tension, fraying, cracking, or glazing; examine radiator and heater hoses for bulging, hardening, or weeping clamps.

Tyres, Wheels, and Rim Integrity Checks

Tyres and wheel assemblies carry massive static and dynamic axle loads. Failure of a steer or drive tyre at highway speeds presents an extreme risk of vehicle rollover or head-on collision.

Tyre Roadworthiness Thresholds

Minimum Legal Tread Depth: Under Australian Design Rules (ADRs) and NSW vehicle standards, tyres fitted to heavy vehicles must maintain a minimum tread depth of 1.5 mm across the entire breadth of the tread and around the entire circumference .

Inflation Pressure: Check tyre pressures cold using an accurate pressure gauge; under-inflated tyres flex excessively, generating intense internal heat that causes sidewall delamination, casing rupture, or tyre fires.

Casing & Sidewall Condition: Ensure tyres are free from deep cuts, exposed steel cords, bulges, sidewall blisters, or uneven scallop wear caused by alignment faults.

Dual Tyre Separation: On dual-wheel assemblies, check the space between the twin tyres. Ensure tyres are properly matched in diameter and circumference. Verify that stones, timber chunks, or road debris are not wedged between the dual tyres, where friction can cause a high-speed blowout or launch projectiles into following traffic.

Wheel & Rim Security Indicators

Rust Streaks: A telltale visual indicator of a loose wheel nut is a reddish-brown rust streak radiating outwards from a stud hole across the wheel disc, caused by microscopic fretting and vibration.

Wheel Nut Integrity: Verify that no wheel nuts are missing, cracked, stripped, or loose. Ensure all wheel nut indicators (yellow plastic pointers) are correctly aligned point-to-point.

Rim Fatigue Cracks: Carefully inspect the wheel disc around the bolt circle and between stud holes for hairline fatigue cracks, which can cause the wheel center to separate from the hub.

Comparison Table: Pre-Departure Inspection Checklist & Action Triggers

Vehicle Subsystem Mandatory Daily Inspection Points Critical Fault Indicator Immediate Required Action

Steer Tyres Tread depth, inflation pressure, sidewall casing Tread depth < 1.5 mm, cords exposed, deep cuts Ground vehicle; replace tyre before departure

Dual Drive Tyres Matching tyre diameters, dual gap clearance Stone wedged between tyres, contact between sidewalls Remove trapped debris; adjust tyre pressure/spacing

Wheel Fasteners Studs, nuts, rim disc bolt circles Rust streaking from nuts, missing nut, rim crack Torque nuts to specification; replace cracked rim

Suspension & Steering Leaf springs, U-bolts, air bags, drag link, tie rods Broken leaf spring, deflated air bag, excessive ball play Do not drive; rectify steering/suspension defect

Lighting & Electrical Headlights (low/high), indicators, stop, clearance Inoperative brake light, broken lens, dead marker Replace bulb/fuse; ensure 100% lighting operation

Glass & Mirrors Windscreen, side windows, flat & convex mirrors Crack in wiper sweep > 30 mm, broken mirror glass Repair windscreen; replace and adjust mirrors

Couplings & Suzi Coils Turntable jaws, kingpin, air & electrical lines Kingpin secondary lock unlatched, leaking air line Re-couple trailer correctly; repair air suzi lines

Steering, Suspension, and Underbody Mechanicals

Steering Linkage: Visually examine the drag link, drop arm, tie rod ends, and steering box mounting bolts for loose hardware, missing split pins, or damaged rubber dust boots.

Suspension Components: Inspect steel leaf spring packs for fractured leaves, shifted spring leaves (indicating broken center bolts), loose axle U-bolts, or weeping hydraulic shock absorbers.

Air Suspension Systems: On air-bag equipped vehicles, verify that air suspension bellows inflate evenly without audible hiss, sidewall chafing, or perished rubber.

  • Lighting, Visibility, Glass, and Cabin Controls
  • Lights and Reflectors

Operate all vehicle lighting circuits to verify correct illumination, color, and flash rates:

Low-beam and high-beam headlights.

Front, side, and rear direction indicators (hazard flashers).

Rear red stop (brake) lights.

Front white/amber and rear red clearance marker lights.

Rear number plate illumination lights (must illuminate plate visible from 20 metres).

Retro-reflective tape and rear marker plates (Class 1A or Class 400 yellow/red reflective chevrons).

Windscreen, Mirrors, and Cabin Ergonomics

Windscreen Condition: Clean windscreen inside and out. Ensure there are no cracks extending into the primary driver vision sweep or bullseye chips exceeding legal limits.

Wipers & Washers: Inspect rubber wiper blades for splitting or hardening; verify effective washer spray pattern across the glass.

Mirror Adjustment: Adjust main flat mirrors and wide-angle convex mirrors to eliminate blind spots along the vehicle flanks and trailer rear corners.

Trailer Couplings, Air Lines, and Load Security

When operating combination vehicles (articulated trucks, truck and dog trailers, or B-doubles):

Fifth Wheel / Turntable: Visually check under the trailer to confirm the fifth wheel locking jaws are completely closed and locked around the trailer kingpin shank. Verify that the secondary safety release handle catch is fully engaged.

Turntable Base & Skid Plate: Confirm there is no gap between the trailer skid plate and fifth wheel top plate. Inspect mounting angle brackets and bolts for security.

Pin & Eye Couplings (Ringfeder / V.Orlandi): On rigid trucks towing drawbar trailers, verify the coupling pin is seated fully through the drawbar towing eye with the safety latch locked down. Check safety chains or wire cables are cross-hitched.

Air & Electrical Lines (Suzi Coils): Connect the red (supply/emergency) and blue (control/service) air lines and 7-pin electrical plug. Ensure lines are supported off the chassis catwalk and do not drag or foul during articulation.

Load Restraint: Walk around the cargo deck to verify all curtains are buckled, container twist locks are engaged and locked, and tie-down straps/chains are correctly tensioned according to the National Heavy Vehicle Load Restraint Guide .

Pre-Trip Documentation & Defect Reporting

Under NSW legislation and the HVNL:

Drivers must record the completion of the pre-departure inspection in the vehicle's Daily Pre-Trip Inspection Sheet , driver log, or electronic fleet management application.

If a safety-critical defect is detected, the driver must report the defect to the fleet operator/workshop manager immediately. The vehicle must not be driven until the defect is repaired by a qualified technician.

Maintaining comprehensive pre-trip records protects the driver and operator by demonstrating statutory due diligence under Chain of Responsibility requirements.

Operational Transport Scenario

Scenario: During a morning pre-departure inspection of a 3-axle rigid refrigerated truck, the driver notices two prominent reddish-brown rust streaks extending outwards from two adjacent wheel nuts on the left-side steer axle. Additionally, a fist-sized granite stone is lodged between the rear dual drive tyres.

Immediate Assessment: The rust streaks indicate that the wheel nuts have lost their clamping torque, allowing micro-movement and stud fretting under load. The trapped stone represents an immediate hazard for catastrophic dual tyre sidewall blowout and high-speed projectile release.

Corrective Procedure: The driver uses a tyre bar to safely dislodge and remove the trapped stone, checking both sidewalls for cuts. The driver immediately reports the loose steer wheel nuts to the depot workshop. A mechanic torques all steer axle wheel nuts to the manufacturer's specified tension (typically 600–650 Nm for 10-stud disc wheels) using a calibrated torque wrench and checks for stud stretching. The driver logs the fault and rectification in the fleet pre-trip register before commencing the trip.

Common Exam Traps & Pitfalls

Trap 1: Minimum Tyre Tread Depth: Exam questions frequently tempt candidates with 1.0 mm or 2.0 mm. Remember that Australian heavy vehicle regulations mandate a minimum tread depth of 1.5 mm across the entire breadth of the tread.

Trap 2: Rust Streaks on Wheel Discs: Rust marks around wheel studs are not cosmetic stains; they are the primary visual indicator of loose wheel nuts caused by vibration.

Trap 3: Dual Tyre Stones: Drivers must never leave stones wedged between dual tyres. The continuous flexing of the tyre casings generates friction heat, leading to blowouts and dangerous flying debris.

Loading diagram... 360-Degree Heavy Vehicle Pre-Departure Walkaround Inspection Sequence