Study guide

7.3 Circuit-Breaker Curves & Breaking Capacity

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

7.3 Circuit-Breaker Curves & Breaking Capacity

Key Takeaways Explain This Topic AI

MCB Type B, C and D characteristics differ mainly in the instantaneous (magnetic) trip current multiples of In

Type B typically trips instantaneously around 3–5 In, Type C around 5–10 In, and Type D around 10–20 In (IEC 60898 teaching ranges — confirm device datasheet)

Breaking capacity (Icu ultimate, Ics service) must be adequate for the prospective fault current at the point of installation

Series or backup protection may allow a downstream device to be used where fault level exceeds its standalone rating — only when manufacturer/cascade data supports it

Curve selection manages start/inrush versus fault sensitivity; it does not replace Ib ≤ In ≤ Iz continuous coordination

Last updated: August 2026

Circuit-Breaker Curves & Breaking Capacity

Quick Answer: MCB curve type (B, C, D) sets the instantaneous magnetic trip band as a multiple of In . Breaking capacity (Icu / Ics) is the fault current the breaker can interrupt without catastrophic failure. Select curve for load behaviour; select breaking capacity for prospective fault current at the board — neither replaces Ib ≤ In ≤ Iz.

Time–Current Curves in Plain Language

A thermal-magnetic circuit-breaker has two regions on its time–current curve:

Thermal / long-time region — inverse time: modest overloads take longer to trip; heavier overloads trip sooner. This region delivers overload protection tied to In.

Magnetic / instantaneous region — above a threshold multiple of In, the breaker opens very quickly (cycles), clearing short-circuit current.

Curve letters B, C, D (IEC 60898 family used widely on Australian final-circuit MCBs) primarily move that instantaneous threshold . They are not different continuous ratings: a 20 A Type B and a 20 A Type C both have In = 20 A for Ib ≤ In ≤ Iz. They disagree on how many times In is needed before the magnetic trip fires.

Type B, C and D — Instantaneous Multiples

Teaching ranges commonly quoted for instantaneous trip (confirm the live product standard/datasheet):

Curve Typical instantaneous trip band Typical application themes

Type B About 3–5 × In Circuits with low inrush — many resistive loads, some general final circuits where fault sensitivity is desired

Type C About 5–10 × In General-purpose Australian commercial/domestic MCBs — fluorescent/LED drivers, modest inductive loads, many socket circuits

Type D About 10–20 × In High inrush — large motors, transformers, some welders — where Type C would nuisance-trip on start

Why the Band Matters

Suppose In = 16 A , Type C. Instantaneous trip might begin near 5 × 16 = 80 A and be guaranteed by about 10 × 16 = 160 A (band teaching — exact limits per datasheet). A motor start drawing 90 A for a fraction of a second may sit inside or outside the magnetic region depending on type and actual curve. Type D raises the magnetic threshold so start current is less likely to instantaneous-trip, while thermal overload protection for sustained excess current remains anchored to In.

Scenario Better curve theme Risk of wrong choice

Lighting / low inrush final circuit Often B or C per design practice Type D may be unnecessarily “deaf” to some faults

  • General GPOs / mixed loads Commonly C in AU practice Type B may nuisance-trip on some electronic loads
  • Large DOL motor Often D (or dedicated motor protection) Type B/C nuisance-trips on start

Capstone items love asking whether to change In or curve when motors trip on start. If continuous load is fine and Ib ≤ In ≤ Iz holds, the answer is often curve / motor protection , not blindly upsizing In (which may then violate In ≤ Iz).

Breaking Capacity — Can It Interrupt the Fault?

Prospective fault current at a switchboard can be several kiloamperes. The breaker must interrupt that current. Two markings appear on many devices:

Symbol Meaning (teaching)

Icu Rated ultimate short-circuit breaking capacity — the maximum fault current the breaker can interrupt under specified conditions; after clearing at Icu, the device may not be fit for further service without inspection/replacement per manufacturer rules

Ics Rated service short-circuit breaking capacity — the fault current the breaker can interrupt and remain suitable for continued service (often expressed as a percentage of Icu on MCCBs)

If prospective fault current at the point of installation exceeds the breaker’s breaking capacity (and no valid backup arrangement applies), the device may fail violently — contacts weld, case ruptures, fault continues. That is a safety defect, not a paperwork nicety.

Prospective Fault Current

Prospective fault current depends on supply transformer size/impedance, service mains, MEN arrangement and the impedance of conductors to the fault location. Near the main switchboard on a robust supply, fault level is highest; at the end of a long final subcircuit it is lower. Designers and assessors care most about the highest fault level the device might see — typically at the board where it is installed.

For the capstone: you may be given a prospective fault current figure and asked whether a 6 kA MCB is adequate on a board with 10 kA prospective fault current. Without cascade data, 6 kA < 10 kA → not adequate standalone.

Series / Backup (Cascade) Protection Themes

Sometimes a downstream breaker with a modest Icu is installed where the raw prospective fault current is higher, because an upstream fuse or MCCB has been proven (by manufacturer cascade tables) to limit let-through energy so the combination is safe. This is backup or cascading protection.

Teaching cautions:

Backup is not a verbal excuse — it requires documented combination data for the specific upstream and downstream devices.

Backup can conflict with discrimination : the upstream device may also open on a heavy fault, blacking out more of the installation (Section 7.4).

“The main fuse will save us” without datasheet support is not competent design.

  • Arrangement Idea Watch-out
  • Standalone Downstream Icu/Ics ≥ prospective fault current Simplest to defend in assessment

Backup / cascade Upstream device limits energy so downstream combination is rated Need manufacturer tables; may sacrifice selectivity

  • Series-rated systems Specific tested combinations Do not invent pairings
  • Curve Versus Breaking Capacity Versus Coordination

Keep three questions separate:

Continuous? → Ib ≤ In ≤ Iz.

Start / inrush without nuisance magnetic trip? → curve type (B/C/D) or dedicated motor protection.

Can it interrupt the fault safely? → Icu/Ics vs prospective fault current (or validated backup).

A Type D 32 A MCB with Icu = 6 kA can still be wrong on a 15 kA board. A Type B 20 A MCB with Icu = 10 kA can still be wrong if Iz is only 18 A. Passing one check never proves the others.

MCCB Adjustable Trips (Brief)

Larger MCCBs may offer adjustable long-time (Ir), short-time and instantaneous settings. Conceptually they still implement overload and fault regions; the “curve” becomes a set of dials rather than a fixed B/C/D letter. Settings must respect cable Iz (continuous), discrimination studies, and manufacturer limits. Do not set instantaneous so high that fault clearing becomes dangerously slow without a documented reason.

Common Exam Traps

Upsizing In to stop motor-start trips instead of selecting Type D / motor protection — then failing In ≤ Iz.

Reading Icu on the label but comparing it to load current instead of prospective fault current .

Assuming every MCB is 6 kA and every Queensland board is below 6 kA without checking.

Confusing Ics with residual current (mA) — completely different quantity.

Bridge Forward

Even a correctly rated, correctly curved breaker is only half the story if an upstream device trips for every downstream fault. Section 7.4 covers discrimination and selectivity .

Loading diagram... Curve type vs breaking capacity checks