Study guide

1.2 Capstone Written & Practical Format

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

1.2 Capstone Written & Practical Format

Key Takeaways Explain This Topic AI

MEM10025 describes a written component using objective methods including a sensible proportion of multiple-choice items plus some written answers, with essay style avoided

MEM10025 permits standards and published reference books but excludes computers and personal notes; UEEEL0039 publishes no reference-material rule, so confirm your RTO list in writing

Competency means satisfactory performance on every critical written item and practical work with no defect categorised as serious by electrical regulators

MEM10025 assessors must hold a current electrical licence and must not be your regular instructor; UEEEL0039 assessors must hold a current Unrestricted Electricians Licence

Open-book success depends on navigation: knowing where AS/NZS 3000 Table 5.1, Appendix C and Section 8 live beats rote memorisation

Last updated: August 2026

Capstone Written & Practical Format

Quick Answer: Expect a written component and a practical component assessed by your RTO. MEM10025 publishes the format most Australian capstones follow: one working day, written ~2–3 hours, practical ~4–6 hours and about 70% of the whole test, objective written methods including a sensible proportion of multiple-choice items plus some written answers, standards and published reference books permitted, computers and personal notes excluded . UEEEL0039 publishes assessor and evidence rules instead of a timetable — confirm your RTO's arrangements in writing.

Two Modes of Proof

A capstone exists so the RTO can see both what you know and what you can do before a licensing authority relies on that judgement. It is deliberately independent of day-to-day apprenticeship marking.

Written component

MEM10025's range of conditions describes the written component as using objective assessment methods , "including a sensible proportion of multiple choice questions ('essay style' to be avoided) and some written answers to the objective questions", aimed at demonstrating understanding of the 'critical' aspects specified in the EPC list . Neither capstone unit publishes a fixed question count, so RTOs structure papers differently while still covering the critical EPCs.

Expect items that force you to:

Locate and apply AS/NZS 3000 clauses (isolation, damp situations, protection, earthing, switchboards, verification).

Select cables or check voltage drop using AS/NZS 3008.1.1 tables and the mV/A·m method.

Apply maximum demand diversity (Appendix C / Table C1 reasoning).

Coordinate protection ( Ib ≤ In ≤ Iz ), select RCDs, and reason about discrimination.

Work d.c. and a.c. circuit theory — Ohm's law, series/parallel behaviour, RMS values, three-phase relationships.

Explain MEN arrangements and calculate earth-fault-loop impedance and disconnection times.

Read and interpret electrical diagrams and specifications .

Connect answers to Queensland electrical safety duties under the Electrical Safety Act 2002 .

Practical component

Under MEM10025 the practical is the majority of the day and requires demonstrated fundamental knowledge and comprehension of electrical concepts and safety principles "using (where possible) problems that test a combination of practical and theoretical knowledge and skills". Tasks probe installation practice, identifying and rectifying non-compliance defects and retesting, safe isolation, testing to the Section 8 sequence, and completing all mandatory documentation.

UEEEL0039's performance evidence is explicit about what you will do: apply WHS requirements; safely measure d.c. circuit parameters; safely isolate (including preparing a SWMS or JSA); determine maximum demand and select mains, submains and final subcircuit cables; select equipment and switchgear; determine maximum fault-loop impedance and conductor sizes; install and terminate consumers mains and subcircuit cabling; complete visual inspection; conduct and report mandatory testing; identify causes of non-compliance from test results; and identify and rectify faults.

Budget your stamina. After a cognitively heavy written paper you still need careful, methodical practical work.

Reference-Material Rules

MEM10025's range of conditions permits standards and published reference books in the written component but states that computers and personal notes are to be excluded . In practice most RTOs extend that to programmable calculators and phones. UEEEL0039 does not publish a reference rule at all.

Typically allowed (confirm with your RTO first):

AS/NZS 3000 Wiring Rules — the edition your RTO specifies.

AS/NZS 3008.1.1 for cable selection.

Other published reference texts the RTO explicitly lists.

Assume excluded unless told otherwise in writing:

Computers , tablets and phones — anything that retrieves notes or browses.

Personal notes , and annotated photocopies functioning as crib sheets.

Programmable calculators and similarly capable devices.

Open book does not mean open phone. It means you may consult the publications the assessor has authorised — if you can find the clause in time.

Competency on Every Critical Item

Written marking is not a soft average. If a critical item is assessed you need a satisfactory result on that item :

Do not skip hard calculation questions hoping other marks will carry you.

Show working an assessor can follow: formula, substituted values, units, and the clause or table you relied on.

In practical work, treat every isolation, polarity, earth continuity, insulation resistance, RCD and loop-impedance check as a professional deliverable.

If you are assessed not yet competent, ask which critical EPCs failed and remediate those specifically before reassessment.

Who Assesses You

Both units impose assessor independence and licensing requirements:

MEM10025 — assessors must hold a current electrical licence and be an assessor other than the one who has been a regular instructor to the apprentice .

UEEEL0039 — assessors must hold a current 'Unrestricted Electricians Licence' issued in an Australian state or territory to assess units relating to the ERAC Essential Performance Capabilities for licensing.

That independence protects the integrity of the licence pathway. Expect formal exam conditions: identity checks, controlled materials and limited communication with peers.

Navigation Strategy — Where Things Live

Under time pressure, navigation beats heroic memorisation. Build a mental map of AS/NZS 3000 before assessment day:

  • Need Where to look first
  • Scope, fundamental principles, definitions Part 1 material — confirm definitions before arguing a clause
  • Protection against electric shock, RCDs, isolation and switching Protection and switching clauses

Damp situations, special locations, classified zones Dedicated special-location clauses — zone thinking matters

  • Earthing, MEN, bonding, electrodes Earthing section, including Table 5.1 for main earthing conductor sizing
  • Switchboards, arrangement, metering Switchboard clauses
  • Cable selection, voltage drop Installation design clauses plus your AS/NZS 3008.1.1 tables
  • Maximum demand diversity Appendix C (Table C1 domestic factors)
  • Verification and testing Section 8 , with AS/NZS 3017 as the verification guideline
  • Exam-day lookup habits

Underline the ask — a value, a clause citation, a compliance decision, or a calculation?

Name the book and part before flipping — "3000 earthing table" beats random thumbing.

Use the contents and index deliberately; mark up only a standard you own and only if permitted.

Copy limits carefully — 0.4 s versus 5 s, 30 mA versus 300 mA, 5% voltage drop. Misreading a table is a classic open-book failure.

Leave breadcrumbs in your working — "AS/NZS 3000 Table 5.1" beside an earth size shows method even if arithmetic slips.

Preparation Checklist

Confirm your capstone unit code (UEEEL0039 or MEM10025) and the permitted publication and calculator list in writing .

Drill timed lookups for Table 5.1, Appendix C, Section 8 and the 3008.1.1 CCC and voltage-drop tables.

Practise non-programmable calculation of voltage drop, demand, adiabatic sizing and EFLI arithmetic.

Rehearse isolation, defect rectification, the full test sequence and the documentation until the order is automatic.

Sleep and eat for a long day — errors rise late in the practical when fatigue hits.