Study guide
1.1 Current Capstone Exam Facts
Queensland Electrical Licence Capstone Assessment Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Capstone Overview
1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway
2 AS/NZS 3000 Fundamentals
2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock
3 Isolation, Switching & Special Locations
3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification
4 Cable Selection Basics (AS/NZS 3008)
4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity
5 Voltage Drop & Selection Order
5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples
6 Maximum Demand Calculations
6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing
7 Circuit Protection Coordination
7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity
8 RCDs, Division of Circuits & SELV/PELV
8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems
9 Earthing & the MEN System
9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding
10 Electrodes, Adiabatic & Prospective Fault Current
10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current
11 Earth-Fault-Loop Impedance & Disconnection
11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC
12 Consumer Mains & Submains
12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream
13 QLD Electrical Safety Legislation
13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)
14 Safe Work & Critical Theory
14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)
15 Testing & Verification
15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation
16 DC, AC & Three-Phase Circuit Theory
16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence
17 Motors, Transformers & Switchboards
17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types
18 Wiring Systems, Aerials & Hazardous Areas
18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones
19 Drawings, Commissioning & Fault Rectification
19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults
20 Workplace Safety, Rescue & High Voltage
20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems
1.1 Current Capstone Exam Facts
Key Takeaways Explain This Topic AI
UEE30820 Certificate III in Electrotechnology Electrician apprentices sit UEEEL0039 as their capstone; MEM10025 is the capstone for MEM31219 Certificate III in Engineering - Industrial Electrician
Both capstone units are written against the Electrical Regulatory Authorities Council Essential Performance Capabilities; MEM10025 Release 4 names 31 EPCs classified as critical
MEM10025 publishes one full working day with the practical about 70% of the test (examples: written 2-3 hours, practical 4-6 hours); UEEEL0039 publishes no durations but requires performance evidence on at least two separate occasions
Assessment is competency-based: satisfactory performance in every critical written item, and practical work free of any defect regulators categorise as serious
- Neither unit publishes percentage domain weights or a fixed official question count
- Last updated: August 2026
Current Capstone Exam Facts
Quick Answer: The Queensland electrical capstone is an RTO-conducted, competency-based written and practical assessment sat at the very end of your apprenticeship. If you trained under UEE30820 Certificate III in Electrotechnology Electrician — the normal Queensland electrician route — your capstone unit is UEEEL0039 . It is the final skills-and-knowledge check before you apply to the Electrical Safety Office for a Queensland electrical work licence.
Know Which Capstone Unit Is Yours
"Capstone" is the industry word for the final integrated assessment before licensing. Nationally there are two capstone units, and they are not interchangeable. Confirm which one your registered training organisation (RTO) has enrolled you in before you buy a single revision book:
Your qualification Your capstone unit Full title
UEE30820 Certificate III in Electrotechnology Electrician (the standard Queensland electrician apprenticeship) UEEEL0039 Design, install and verify compliance and functionality of general electrical installations
MEM31219 Certificate III in Engineering – Industrial Electrician MEM10025 Undertake a capstone assessment
MEM10025's published Application states plainly that it is carried out after all other assessment requirements of the units that make up MEM31219 , and prior to application for an electrical licence. UEEEL0039 is the first-release capstone unit in the UEE Electrotechnology Training Package and is the final unit UEE30820 apprentices complete. Queensland guidance on electrician apprenticeships lists UEEEL0039 as the UEE30820 unit for the design/install/verify capstone outcome.
Most readers of this guide are on the UEE30820 → UEEEL0039 path. Everything taught here serves both units, because both are built on the same national capability list.
The Real Blueprint: ERAC Essential Performance Capabilities
Neither capstone unit publishes percentage domain weights, and neither publishes a fixed official question count. What they do publish is far more useful: both are written against the Electrical Regulatory Authorities Council (ERAC) Essential Performance Capabilities (EPCs) .
MEM10025 Release 4 names the EPCs it classifies as 'critical' — 31 of them, spanning EPC 2 through EPC 54. UEEEL0039's assessment conditions require assessors to hold an unrestricted electrician's licence specifically so they can assess "units of competency relating to the Electrical Regulatory Authorities Council (or their successor) Essential Performance Capabilities for licensing", and its knowledge evidence covers the same ground bullet for bullet.
That critical-EPC list is the blueprint this study guide is built to. It is why the chapters ahead go well past the Wiring Rules: alongside cable selection, maximum demand, protection, MEN earthing and testing, the critical EPCs also require d.c. and a.c. circuit theory, motors, transformers, switchboards, hazardous areas, aerial and underground wiring, electrical drawings, rescue and CPR, high-voltage dangers, commissioning and fault diagnosis. A revision plan that stops at AS/NZS 3000 calculations is a revision plan with holes in it.
Timing and Structure
MEM10025 Release 4 publishes concrete duration guidance in its range of conditions:
- Component Published example Share
- Written About 2–3 hours Minority of the day
- Practical About 4–6 hours About 70% of the whole test
- Overall One full working day Written + practical together
Its assessment conditions add that the capstone is "an entirely RTO conducted assessment at the RTO's chosen location where the entire assessment needs to be carried out in one day."
UEEEL0039 publishes no component durations, no percentage split and no open-book rule. What it does publish is different and worth knowing: performance evidence must satisfy the elements, performance criteria and range of conditions on at least two separate occasions , and assessment must occur in workplace operational situations or in simulated conditions that replicate them. So do not assume a UEE capstone is a single clock-managed day just because MEM10025 describes one — ask your RTO for its timetable in writing.
Competency-Based — Not a Percentage Pass Mark
Both units are competency-based . MEM10025 states the minimum requirements directly:
Written — the apprentice must demonstrate satisfactory performance in every 'critical' item tested . There is no averaging up.
Practical — the apprentice must demonstrate competence for the 'critical' items tested, where competence means the person comprehends the key safety issues and the practical work does not suffer any defect categorised as 'serious' by electrical regulators .
That is a stricter standard than "70% and you pass". One serious practical defect — an unsafe termination, a missed isolation, energising before verification — can end the day regardless of how well the written paper went.
Standards and Legislation That Frame the Knowledge
AS/NZS 3000 Wiring Rules — scope and fundamental principles, conductor identification, isolation and switching, damp situations and special locations, protection against electric shock, earthing and MEN, division of circuits, switchboards, and the Section 8 verification sequence.
AS/NZS 3008.1.1 — current-carrying capacity, installation methods, grouping and derating, and the mV/A·m voltage-drop method.
AS/NZS 3012 — construction and demolition sites. AS/NZS 3017 — verification guidelines.
Electrical Safety Act 2002 (Qld) and the Electrical Safety Regulation 2013 — who may perform electrical work, licence duties, and certificates of testing and compliance.
Numbers worth committing early: the 5% voltage-drop limit, 1 MΩ insulation resistance at 500 V DC , 0.4 s and 5 s disconnection times, 30 mA RCD additional protection, and the Ib ≤ In ≤ Iz coordination rule. Exact clause application still belongs in the standard — the capstone rewards people who can find and apply the clause under time pressure.
How to Use This Study Guide
Section 1.2 covers written versus practical format, reference-material rules and navigation tactics. Section 1.3 maps the ESO licence pathway, fees and the Queensland rescue-and-resuscitation rule. Chapters 2–15 build the AS/NZS 3000 design and verification core; chapters 16–20 cover the remaining critical EPCs that trip up candidates who revised only the Wiring Rules.