Study guide

12.3 Submains Definitions & Sizing

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

12.3 Submains Definitions & Sizing

Key Takeaways Explain This Topic AI

Submains are circuits originating at the main switchboard (or a distribution switchboard) and supplying another distribution board — not final loads directly

Size submains to the maximum demand of the portion of the installation they supply, applying diversity where the demand method permits

Submains require the same CCC, voltage-drop and fault/protection checks as other distribution circuits

A submain must include a protective earthing conductor (or compliant equivalent arrangement) so the downstream board’s earth bar ties back to the main earthing system — without a local MEN link

Capstone drawings distinguish consumer mains, submains and final subcircuits by topology, not by cable thickness alone

Last updated: August 2026

Submains Definitions & Sizing

Quick Answer: A submain is a circuit from the main switchboard (or from one distribution board) to another distribution board . Size it to the maximum demand of the portion it supplies , using diversity where allowed, then verify CCC , voltage drop and fault protection . Carry a protective earthing conductor with the submain so the sub-board earth bar bonds back to the main earthing system — do not fit a MEN link on the sub-board.

Definition — Topology, Not Cable Size

Candidates often think “big cable = submain”. Wrong. Classification is about what the circuit feeds :

  • Circuit type From To
  • Consumer mains Consumers terminals / POS arrangement Main switchboard
  • Submain MSB (or DB) Another distribution board
  • Final subcircuit Switchboard Luminaires, socket-outlets, fixed equipment

A short 6 mm² run from MSB to a laundry DB is still a submain . A long 35 mm² consumer mains run to the MSB is still consumer mains . Thickness does not rename the circuit.

Why Submains Exist

Practical installations distribute protection and control:

House MSB feeds a garage DB, shed DB, or upper-floor DB.

Commercial MSB feeds tenancy boards or plant boards.

Construction and temporary supplies use distribution assemblies fed by submains.

Submains let you keep origin protection manageable while placing local protective devices near loads. They also create the earthing and neutral topology that Section 12.4 polices strictly.

  • Demand and Diversity on Submains
  • Portion demand

Calculate maximum demand for the part of the installation supplied by that submain , not the whole site MD, unless the submain truly carries everything (rare if other circuits leave the MSB).

Example pattern: whole dwelling MD = 70 A on consumer mains; garage submain supplies only garage power and lighting with a calculated portion demand of 28 A after diversity → submain sized from ~28 A upward (then CCC/Vd/fault), not automatically 70 A.

Diversity

Appendix C / demand methods often already embed diversity for domestic load groups. For commercial and multi-board arrangements, further diversity may apply between load groups on a submain depending on the method used. Exam expectation:

State which loads the submain supplies.

Apply the correct demand/diversity method for those loads.

Do not double-count diversity illegally, and do not ignore diversity where the method provides it.

Trap: Using the sum of downstream breaker ratings as submain current with no demand method — oversizing wastefully or, worse, still getting Vd wrong because length was ignored.

The Same Four Engineering Checks

Demand of the supplied portion (with diversity as applicable).

CCC for the installation method of the submain route (in roof space, underground to shed, clipped in garage, etc.).

Voltage drop — remember consumer mains have already used part of the budget; submain + finals must fit in what remains.

Fault / protection — submain protective device at the origin (usually MSB) must protect the submain cable and support required disconnection times for distribution circuits (often discussed in the 5 s distribution-circuit disconnection context, distinct from many 0.4 s final-subcircuit cases — confirm tables in AS/NZS 3000).

Protective device location

The submain OCPD is typically at the supply end (MSB). The downstream DB then has its own circuit-breakers/RCDs for final subcircuits. Do not leave a long submain unprotected because “the finals have breakers”.

Conductors in a Submain — Including Earth

A compliant submain to a MEN installation distribution board generally includes:

Active conductor(s).

Neutral conductor.

Protective earthing conductor connecting the DB earth bar back to the main earthing system.

At the distribution board:

Neutrals land on a neutral bar (no MEN link).

Earths land on an earth bar (no MEN link).

Bars remain separate .

Omitting the submain earth and “just bonding N–E at the shed board” is one of the most dangerous wrong answers in the entire licence syllabus.

Single-Phase and Three-Phase Submains

Garages and sheds are often single-phase; plant rooms and commercial tenancies may be three-phase. For three-phase submains:

Assess per-phase demand correctly.

Size neutral per the applicable rules for the load balance and harmonic considerations where relevant to the question.

Keep earth continuous regardless of phase count.

Worked Capstone Sketch Narrative

Drawing shows:

Energex underground service to meter panel (POS / consumers terminals).

Consumer mains to house MSB (MEN link here).

Submain A to garage DB.

Submain B to rear shed DB.

Finals from each board.

Assessment tasks typically include:

Name each cable run correctly.

Calculate portion MD for Submain B (shed tools + lights).

Select cable for method (e.g. underground to shed) with CCC + Vd.

Show earth bar at shed without MEN link.

Identify that an illegal N–E link at the shed would parallel the submain neutral with the earth conductor back to the MSB.

Common Sizing Mistakes

Sizing every submain to full installation MD “to be safe” without checking Vd and cost — not always wrong electrically if CCC/Vd pass, but often wrong relative to the demand method the question required.

Ignoring voltage drop on a 40 m shed run after spending the budget on consumer mains.

Using indoor CCC for an underground submain.

Forgetting earth continuity to the DB.

Treating a submain as a final subcircuit and applying only 30 mA RCD logic without origin OCPD cable protection reasoning (RCDs on finals remain required where mandated, but they do not redefine the submain).

Coordination with Chapters You Already Studied

Ch 6 Maximum demand — portion demand and diversity.

Ch 4–5 Cable selection & Vd — tables and drop calculations.

Ch 7 Protection — device rating and disconnection.

Ch 9 MEN — earth return path remains via MSB MEN link; submain earth is a PEC, not a second MEN.

Bridge to Separation Rules

Section 12.4 focuses on the non-negotiable rule that makes submain earthing safe: neutral and protective earth remain separate downstream of the MEN link . If you understand submain topology, the illegal-link failure modes become obvious rather than memorised slogans.

Loading diagram... Submain from MSB to distribution board