Study guide

17.2 Motor Overload & Short-Circuit Protection

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

17.2 Motor Overload & Short-Circuit Protection

Key Takeaways Explain This Topic AI

A motor circuit needs two different protections: short-circuit protection sized for fault current, and overload protection set to the motor full-load current

Thermal overload relays use bimetal strips that mimic motor heating; magnetic relays respond to current magnitude; thermistors sense actual winding temperature

Trip classes 10, 20 and 30 describe how long the relay tolerates a 7.2 times full-load current start before tripping

Single-phasing is the classic motor killer: the remaining windings carry roughly 1.73 times normal current and overheat quickly

Every motor needs an isolator for mechanical maintenance that is adjacent to the machine or capable of being locked in the off position

Last updated: August 2026

Motor Overload & Short-Circuit Protection

Quick Answer: A motor circuit carries two separate protective duties . Short-circuit protection (fuse or breaker) clears faults and is sized above starting current. Overload protection (thermal relay, magnetic relay or thermistor) is set to the motor’s full-load current and protects the windings from sustained overcurrent. One device rarely does both well.

Two Duties, Two Devices

Duty Threat Typical device Setting basis

Short circuit Bolted or arcing fault, thousands of amperes Motor-rated circuit breaker, MCCB with magnetic-only trip, or HRC fuse Above starting current, below cable withstand

Overload Sustained 105–300% current from mechanical load, single-phasing, low voltage Thermal overload relay, electronic relay, or thermistor circuit Set to motor full-load current from the nameplate

The reason they are separated is the starting transient. A single device set low enough to protect the windings against a 15% overload would trip during every start; a device set high enough to allow starting would let the motor cook at 150% load indefinitely.

Thermal Overload Relays

The traditional bimetal relay places heater elements in each line. Current heats bimetal strips which bend and, after a time proportional to the heating, operate a contact that drops out the contactor coil. Because heating is an I²t process, the relay mimics the motor’s own thermal behaviour: a small overload takes minutes to trip, a large one takes seconds.

Setting discipline:

Set the dial to the nameplate full-load current , adjusted for the actual supply voltage and connection.

On a star-delta starter, the relay may sit in the delta leg and must be set to FLC / √3 — a classic capstone trap.

Ambient temperature compensation matters when the starter enclosure is hotter than the motor.

Magnetic Overload Relays

Magnetic (electromagnetic) relays respond to current magnitude through a solenoid rather than accumulated heat, sometimes with an oil dashpot providing time delay. They are less common in modern general installations but appear in older switchgear and in applications needing an adjustable instantaneous element.

Thermistor (Direct Temperature) Protection

Positive temperature coefficient thermistors are embedded in the motor windings during manufacture. Their resistance rises sharply at a defined temperature, and a relay monitoring them trips the contactor.

Advantages over current-based methods:

Protects against cooling failure — a blocked fan or blanketed motor overheats at normal current, which a thermal relay will never see.

Protects motors on variable speed drives , where reduced speed reduces self-cooling but current looks normal.

Protects against high ambient and frequent starting.

Thermistor protection is the correct answer whenever a stem describes overheating with normal current readings.

Trip Classes

Trip class states how long the overload relay will tolerate a start at 7.2 × FLC :

  • Class Trip time at 7.2 × FLC Typical use
  • Class 10 ≤ 10 s Standard duty, quick starts — pumps, fans
  • Class 20 ≤ 20 s Longer starts — loaded conveyors, some compressors
  • Class 30 ≤ 30 s High-inertia loads — large fans, centrifuges

Selecting Class 10 for a high-inertia fan produces nuisance trips on start. Selecting Class 30 for a small pump leaves the windings exposed for three times longer than necessary during a genuine stall.

Single-Phasing — the Classic Motor Killer

If one line conductor opens (blown fuse, loose termination, broken conductor), a running three-phase motor keeps turning on two phases. The remaining windings carry roughly √3 ≈ 1.73 times their normal current and overheat rapidly, while the motor may still sound approximately normal to a passer-by.

Protection responses:

A three-pole thermal relay senses the elevated current in the remaining phases and trips.

A phase-failure relay monitors all three lines and trips on loss or severe imbalance.

Thermistors catch the resulting winding temperature rise directly.

A stall or locked rotor produces the same overheating faster: locked-rotor current continues indefinitely because the rotor is not accelerating away from it.

Coordination With the Cable

The complete chain must satisfy the coordination logic from Chapter 7:

Ib — the motor full-load current, plus any allowance the design requires.

In — the short-circuit protective device rating, chosen above starting current.

Iz — the cable current-carrying capacity after derating, which must still be at least Ib and be protected against overload by the overload relay.

Note the important variation: on a motor circuit, overload protection of the cable is provided by the overload relay , not by the upstream short-circuit device. That is what allows In to sit above Iz in a properly designed motor starter arrangement — a point assessors probe because it appears to contradict the general rule.

Isolation for Mechanical Maintenance

Every motor needs a means of isolation for mechanical maintenance that is either adjacent to the machine or capable of being secured in the off position . Requirements to state on the practical:

The isolator must break all live conductors and be clearly labelled with the machine it controls.

It must be lockable, or the arrangement must otherwise prevent inadvertent reconnection.

A VSD-fed motor may store energy in the DC bus — observe the manufacturer’s discharge time before working on terminals.

Isolating the control circuit alone is never sufficient; the power circuit must be proved dead at the point of work.

Loading diagram... Motor circuit protection chain