Study guide

13.2 Licensing Classes & Worker Duties

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

13.2 Licensing Classes & Worker Duties

Key Takeaways Explain This Topic AI

An electrical work licence authorises an individual to perform electrical work within the licence class and conditions

An electrical contractor licence is required for a business that contracts to perform electrical work for others — it is separate from the individual’s work licence

Only appropriately licensed (or otherwise authorised) persons may perform electrical work; apprentices and restricted classes work under defined supervision/scope rules

Licence holders must comply with conditions, work electrically safely, and PCBUs must ensure workers are appropriately licensed

Capstone questions often fail candidates who merge ‘qualified electrician’ with ‘contractor licence’ or who ignore supervision limits

Last updated: August 2026

Licensing Classes & Worker Duties

Quick Answer: Hold an electrical work licence to perform electrical work as an individual within your class and conditions. If a business contracts to do electrical work for others, it also needs an electrical contractor licence . Unlicensed electrical work, work outside class, and unsupervised work beyond what the Act/Regulation allow are compliance failures — not paperwork delays.

Two Licences, Two Jobs

Queensland’s regime deliberately splits personal competence from business contracting authority:

  • Instrument Who holds it What it primarily authorises
  • Electrical work licence Individual (e.g. electrician) Performing electrical work of the licensed class

Electrical contractor licence Business entity (sole trader, partnership, company) Contracting to perform electrical work for others / carrying on the electrical contracting business

You can be a highly competent licensed electrician employed by a licensed contractor and still not be the contractor licence holder. Conversely, a company can hold a contractor licence only if it meets ESO requirements (including having appropriately licensed people actually do the work).

Exam failure pattern

Stem: “Sam just got an electrical work licence. Sam’s new sole-trader business can immediately advertise ‘fully licensed electrical contracting’ without any further licence.”

Correct reasoning: Sam’s work licence covers Sam performing work of that class. Contracting as a business for electrical work generally requires the contractor licence as well. Treating them as one card is wrong.

Who May Perform Electrical Work?

Under the Act’s licensing scheme, electrical work must be performed by a person who is authorised — typically:

A holder of an electrical work licence of the appropriate class, working within conditions and restrictions on that licence; or

A person working under a recognised training / apprenticeship arrangement with the supervision the law and licence conditions require; or

A person covered by a restricted electrical work licence or other specific authorisation for defined tasks only (for example certain equipment-limited work), always within that narrow scope.

What you must not do:

Perform full electrical installation work on a “mate’s rates” basis without holding the correct licence.

Supervise in name only while an unlicensed person does the skilled work.

Stretch a restricted licence into unrestricted electrician work.

Assume an interstate licence automatically equals a Queensland work licence without mutual recognition / application steps the ESO publishes.

Apprentices and trainees

Apprentices learn by doing supervised electrical work as part of a formal training contract. Supervision is a safety and legal control, not a courtesy. Capstone and workplace culture both expect you to know that “the apprentice was careful” does not replace licensed supervision where the law requires it.

Duties of Licensed Electrical Workers

Holding an electrical work licence creates ongoing obligations. For exam purposes, group them as follows.

1. Stay inside class and conditions

Section themes in the Act require licence holders to comply with conditions and restrictions on the licence. If your licence is restricted to certain equipment or contexts, do not take unrestricted installation work. If a condition requires supervision arrangements, follow them.

2. Work electrically safely

Licensed work must be performed so that persons and property are electrically safe . That duty connects directly to AS/NZS 3000 design and Section 8 verification: defective MEN links, missing RCD additional protection where required, wrong polarity, and energising untested circuits are not “style preferences” — they are safety failures with regulatory consequences.

3. Competence and honesty about scope

Accept jobs you are licensed and competent to complete. Declining work outside your class is professional compliance, not weakness. Fabricating competence or borrowing someone else’s licence identity is a serious integrity breach.

4. Documentation and testing interfaces

Where the Regulation requires testing before connection/energisation and certificates to customers (Section 13.3), licensed workers operating under a contractor must support those obligations. Leaving a site “live” without required testing because “the painters were waiting” is exactly the behaviour the legislation targets.

Duties Around the Worker — PCBU and Contractor Themes

The Act also places duties on persons conducting a business or undertaking and on electrical contractor licence holders. Exam-relevant themes include:

Ensuring workers who perform electrical work are appropriately licensed for the work assigned.

Not directing or allowing unlicensed persons to perform electrical work that requires a licence.

Ensuring the way electrical work is performed is electrically safe, and that negligence/incompetence in performance is not tolerated as a business model.

Giving required notices/certificates about electrical work (expanded in 13.3).

Maintaining insurance and other contractor-licence conditions where the ESO and Regulation require them for contractor licence holders.

A licensed electrician working for a contractor still has personal licence duties; the contractor entity has parallel business duties. Markers like questions that force you to assign responsibility correctly rather than saying “someone should have been careful.”

Restricted Work and Specialty Pathways (Awareness)

Queensland also uses restricted electrical licensing for defined scopes (for example certain appliance or equipment work, or specialised testing pathways where the ESO authorises them). The teaching rule for capstone candidates aiming at the full electrician pathway is:

Know that restricted ≠ unrestricted electrician .

Know that test-and-tag for others can attract its own contractor/restricted licensing expectations under ESO administration.

Do not treat a short course certificate alone as a full electrical work licence.

Network Interface Duties Awareness

When your work touches the point of supply , metering, or service equipment, remember Energex/Ergon rules and seals. Licensed electrical workers still must not interfere with distributor assets outside authorised arrangements. Licence authority to work on the consumer’s installation is not a blank cheque to alter network service fuses or metering without the correct process.

Capstone Application — Scenario Drill

Scenario A: A homeowner asks an apprentice to “just add two power points this weekend” with no licensed supervisor on site.

Analysis: Likely unlawful/unauthorised electrical work and a supervision failure. Stop; arrange licensed supervision or a licensed worker.

Scenario B: A licensed electrician employed by a contractor completes a switchboard upgrade. The business has let its contractor licence lapse but still invoices as an electrical contractor.

Analysis: Individual work-licence status does not cure a missing contractor licence for the contracting business. The business side is non-compliant.

Scenario C: A worker holds only a restricted licence for a narrow equipment class but accepts a full house rewire.

Analysis: Outside licence class/conditions — refuse or obtain the correct licence pathway first.

Bridge Forward

Once you know who may work, Section 13.3 explains how completed work is evidenced: certificates of testing and safety / testing and compliance, retention periods, and the duty to test before energising or connecting. Section 13.4 then takes those safety expectations onto construction and demolition sites under AS/NZS 3012.

Loading diagram... Work licence vs contractor licence