Study guide

15.3 Insulation Resistance (1 MΩ at 500 V DC)

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

15.3 Insulation Resistance (1 MΩ at 500 V DC)

Key Takeaways Explain This Topic AI

For typical low-voltage installations under AS/NZS 3000, insulation resistance is commonly required to be at least 1 MΩ when tested at 500 V DC — confirm the live Standard for special cases and circuit groupings

IR is a dead test performed after continuity and before energising for loop impedance and RCD operation

Prepare the circuit: isolate supplies, disconnect or protect equipment that can be damaged by the test voltage, and remove paths that falsely lower readings

Record measured values, test voltage, and circuit identity — certificate documentation depends on traceable IR results

Readings below the minimum, or unexplained asymmetry between circuits, are defects that must be investigated before the installation is verified

Last updated: August 2026

Insulation Resistance (1 MΩ at 500 V DC)

Quick Answer: With the installation isolated, measure insulation resistance at the specified DC test voltage. For typical LV work under AS/NZS 3000, expect ≥ 1 MΩ at 500 V DC unless a special case in the live Standard says otherwise. Pass IR before any energised loop or RCD testing.

What insulation resistance verifies

Insulation resistance (IR) checks that insulating materials between conductors — and between live conductors and earth — can withstand the applied DC test voltage with leakage current low enough to meet the minimum megohm value. It is the principal instrumental proof that wiring is not shorted to earth through damaged insulation, moisture, conductive dust, or pinched sheaths.

IR does not replace continuity, polarity, loop impedance, or RCD tests. A circuit can show excellent megohms and still have an open earth or wrong polarity.

The 1 MΩ / 500 V DC benchmark

For many low-voltage installation circuits, AS/NZS 3000 uses a practical acceptance level of not less than 1 MΩ with a 500 V DC insulation tester (or the Standard’s stated equivalent method). That pair — 1 MΩ at 500 V DC — is the figure Queensland capstone candidates must know cold, then confirm in the live edition for:

  • SELV/PELV and other extra-low-voltage arrangements
  • Situations where a different test voltage is specified
  • Combined circuit testing rules and when circuits may be tested together
  • Any amended minimums or notes for particular equipment

Do not invent tighter or looser limits from internet summaries when the open-book Standard is in front of you.

  • Item Typical LV expectation Capstone reminder
  • Test voltage 500 V DC (as applicable) Select the correct tester range
  • Minimum IR ≥ 1 MΩ (general LV case) Confirm special cases in AS/NZS 3000
  • When performed After earth continuity; before energising Sequence defect if skipped
  • Record Value, voltage, circuit ID, date Feeds certificate evidence
  • Preparing the circuit (where candidates lose marks)

Bad preparation causes false fails and damaged equipment:

Isolate and prove dead — IR is a dead test; never apply 500 V DC to an energised circuit.

Protect vulnerable equipment — surge protective devices, electronic ballasts, dimmers, control boards, and some appliances can be damaged by IR test voltage. Disconnect, isolate, or follow manufacturer/Standard guidance.

Account for neon indicators, PIRs, and connected loads that provide a leakage path to earth and drag readings down.

Open switching as required so you are testing the intended conductors.

Ensure earth reference is valid — IR to earth needs a continuous earthing system; that is why continuity comes first.

If a reading is low, do not immediately condemn the entire subcircuit: bisect the run, remove loads, and find whether the fault is cable, accessory, or connected equipment.

Performing the measurement

A typical method (align with your RTO procedure and the Standard):

Select insulation-resistance mode at 500 V DC (or the required voltage).

Test between active(s) and earth, neutral and earth, and between live conductors as required for the verification scope.

Allow the reading to stabilise; capacitive cable runs may climb as charge settles.

Discharge conductors after high-voltage testing as trained.

Record the stable value.

Interpret results against the minimum. A reading of 0.2 MΩ on a 230 V final subcircuit that should meet ≥ 1 MΩ is a fail — investigate moisture, damaged sheath, nail penetrations, or N–E/A–E faults. A reading of tens or hundreds of megohms on a dry, new circuit is common and acceptable if above the minimum.

Why IR before loop and RCD

Energising for Zs or RCD tests applies mains voltage to the installation. If insulation is already inadequate:

  • Shock and fire risk rise immediately
  • Protective devices may operate unpredictably
  • You may waste time collecting live data on a circuit that was never safe to energise

Section 8 sequence exists so IR is the gate. Capstone assessors treat “I’ll IR it later” after live testing as a serious process failure.

Documentation for certificates

Queensland certification pathways expect recorded test results, not memory. Your IR column should show:

  • Circuit or distribution board reference
  • Test voltage used
  • Measured resistance (MΩ)
  • Pass/fail against the criterion used
  • Notes on disconnected equipment or deferred tests

Vague entries such as “IR OK” without values weaken the evidentiary trail for a Certificate of Testing and Compliance / related testing documents and invite assessor questions.

Special cases and professional judgement

Not every situation is a plain 1 MΩ domestic lighting circuit. Motors with moisture, long feeder runs, mixed circuits tested together, and equipment still connected can all change readings. The competent approach is:

  • Apply the Standard’s stated method for that situation
  • Separate circuits when combined testing obscures a fault
  • Never lower the acceptance criterion to “make it pass”

Retest after drying, repair, or reconnection of temporarily removed equipment if the verification scope requires a final in-service state

Capstone practical emphasis

Expect to be marked on whether you:

  • Choose 500 V DC (when applicable) without guessing AC ranges
  • Isolate and prepare correctly
  • Achieve and record ≥ 1 MΩ where that is the criterion
  • Stop the sequence on a fail
  • Explain how IR evidence supports the certificate

Competence here is not optional polish — it is a critical electrical performance item on the capstone.

Loading diagram... Insulation resistance gate before energised tests