Study guide

18.4 Hazardous Areas & Classified Zones

Queensland Electrical Licence Capstone Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Capstone Overview

1.1 Current Capstone Exam Facts 1.2 Capstone Written & Practical Format 1.3 Queensland ESO Licence Pathway

2 AS/NZS 3000 Fundamentals

2.1 Scope & Fundamental Principles 2.2 Nominal Voltages & System Classifications 2.3 Conductor Identification & Colour Coding 2.4 Protection Against Electric Shock

3 Isolation, Switching & Special Locations

3.1 Isolation & Switching 3.2 Special Locations (Bathrooms, Pools & More) 3.3 Installation Defects & Rectification

4 Cable Selection Basics (AS/NZS 3008)

4.1 Current-Carrying Capacity & Installation Methods 4.2 Reference Temperatures & Insulation Types 4.3 Grouping & Thermal Derating Factors 4.4 Cable Short-Circuit Capacity

5 Voltage Drop & Selection Order

5.1 Voltage Drop (mV/A·m) & the 5% Limit 5.2 Order of Cable-Selection Checks 5.3 Worked Cable Selection Examples

6 Maximum Demand Calculations

6.1 Diversity & Appendix C Overview 6.2 Domestic Table C1 Demand Factors 6.3 Commercial Demand & Mains/Main-Switch Sizing

7 Circuit Protection Coordination

7.1 Overload & Short-Circuit Protection 7.2 The Ib ≤ In ≤ Iz Coordination Rule 7.3 Circuit-Breaker Curves & Breaking Capacity 7.4 Discrimination & Selectivity

8 RCDs, Division of Circuits & SELV/PELV

8.1 RCD Types & 30 mA Additional Protection 8.2 Division of Circuits 8.3 SELV & PELV Systems

9 Earthing & the MEN System

9.1 MEN System Principles & Fault Return Path 9.2 The MEN Link at the Main Switchboard 9.3 Main Earthing Conductor Sizing (Table 5.1) 9.4 Equipotential Bonding

10 Electrodes, Adiabatic & Prospective Fault Current

10.1 Earth Electrodes & Arrangements 10.2 The Adiabatic Equation for Protective Conductors 10.3 Prospective Fault Current

11 Earth-Fault-Loop Impedance & Disconnection

11.1 Earth-Fault-Loop Impedance (Zs = Ze + R1 + R2) 11.2 Disconnection Times (0.4 s & 5 s) 11.3 Breaking Capacity Coordination with PFC

12 Consumer Mains & Submains

12.1 Point of Supply Definitions 12.2 Consumer Mains Sizing & Installation 12.3 Submains Definitions & Sizing 12.4 Neutral & Earth Separation Downstream

13 QLD Electrical Safety Legislation

13.1 Electrical Safety Act 2002 & the ESO 13.2 Licensing Classes & Worker Duties 13.3 Certificates of Testing & Compliance 13.4 Construction Sites (AS/NZS 3012)

14 Safe Work & Critical Theory

14.1 Safe Isolation & Lock-Out/Tag-Out 14.2 Energised Electrical Work Controls 14.3 Effects of Electric Current (Critical EPC Theory)

15 Testing & Verification

15.1 AS/NZS 3000 Section 8 Test Sequence 15.2 Earth Continuity & Polarity 15.3 Insulation Resistance (1 MΩ at 500 V DC) 15.4 RCD Testing & Loop-Impedance Verification 15.5 AS/NZS 3017 Verification, Reporting & Documentation

16 DC, AC & Three-Phase Circuit Theory

16.1 DC Circuits, Ohm’s Law & Power 16.2 AC Generation, RMS Values & Phase 16.3 Three-Phase Systems & Phase Sequence

17 Motors, Transformers & Switchboards

17.1 Motor Selection, Enclosures & Starting Methods 17.2 Motor Overload & Short-Circuit Protection 17.3 Transformer Key Safety Issues 17.4 Switchboard Location, Arrangement & Form Types

18 Wiring Systems, Aerials & Hazardous Areas

18.1 Cable Installation & Termination Requirements 18.2 Final Subcircuits Into Switchboards 18.3 Aerial Conductors & Underground Wiring 18.4 Hazardous Areas & Classified Zones

19 Drawings, Commissioning & Fault Rectification

19.1 Reading, Sketching & Interpreting Electrical Diagrams 19.2 Commissioning & Decommissioning 19.3 Diagnosing & Rectifying Faults

20 Workplace Safety, Rescue & High Voltage

20.1 Statutory WHS Duties, Supervision & Duty of Care 20.2 Asbestos, Silica & Hazardous Gases 20.3 Workplace Safety Checks & Hazard Control 20.4 Rescue From Live Electrical Conductors 20.5 Electric Shock First Aid & CPR 20.6 High Voltage Dangers & Distribution Systems

18.4 Hazardous Areas & Classified Zones

Key Takeaways Explain This Topic AI

EPC 28 requires awareness of hazardous area requirements and the standards referenced, not full hazardous area competence

A hazardous area is one where flammable gas, vapour, mist, dust or fibres may be present in sufficient quantity to require special precautions

Gas atmospheres are classified as Zone 0, 1 or 2 and dust atmospheres as Zone 20, 21 or 22, by how likely and how long an explosive atmosphere is present

Equipment must be selected and installed to the explosion-protection technique appropriate to the zone, gas group and temperature class

Additional formal training and, in many cases, a separate competency is required before working on hazardous area installations — a general electrical licence is not sufficient

Last updated: August 2026

Hazardous Areas & Classified Zones

Quick Answer: A hazardous area is one where a flammable atmosphere may be present. Areas are classified into zones by how likely and how long that atmosphere exists, and equipment must be selected to a matching explosion-protection technique , gas group and temperature class. A general electrical work licence does not authorise hazardous area work — additional training and competency are required.

What EPC 28 Actually Asks For

Read the capability carefully. EPC 28 requires knowledge of the AS/NZS 3000 requirements for hazardous areas and an awareness of the standards to which it refers , together with awareness of the additional training required to work competently there. It is a scope-and-awareness capability, not a licence to design a petrol station.

That distinction is itself examinable. The correct answer to "you are asked to install a light fitting in a spray booth" is not "select an IP66 fitting" — it is "this is a classified hazardous area; I need hazardous area competency and the area classification documentation before I do anything."

What Makes an Area Hazardous

An area is hazardous when a flammable atmosphere may be present in sufficient quantity to require special precautions for the construction, installation and use of electrical equipment. The three ingredients of ignition must be considered together: fuel (gas, vapour, mist, dust or fibre), oxygen, and a source of ignition — which in our trade means arcs, sparks and hot surfaces.

Typical locations:

  • Location Hazard
  • Petrol stations and fuel storage Petrol vapour
  • Paint and spray booths Solvent vapour and overspray
  • LPG storage and decanting Flammable gas
  • Grain silos, flour mills, sugar handling Combustible dust
  • Timber processing, textile mills Combustible dust and fibres
  • Sewage and biogas plant Methane and hydrogen sulfide
  • Battery charging rooms Hydrogen
  • Some agricultural and mining operations Gas and dust

Battery charging rooms catch people out — a bank of flooded lead-acid cells on charge releases hydrogen, and hydrogen has a very wide flammable range.

Zone Classification

Gas, vapour and mist:

  • Zone Presence of explosive atmosphere
  • Zone 0 Present continuously, or for long periods, or frequently
  • Zone 1 Likely to occur in normal operation occasionally
  • Zone 2 Not likely in normal operation, and if it does occur, will persist only for a short period

Dust:

  • Zone Presence of combustible dust cloud
  • Zone 20 Present continuously, or for long periods, or frequently
  • Zone 21 Likely to occur in normal operation occasionally
  • Zone 22 Not likely in normal operation, and only for a short period

Classification is a documented engineering exercise producing a hazardous area classification drawing . An electrician does not classify an area by looking at it; the electrician reads the classification and installs to it.

Equipment Selection

Equipment for a hazardous area is selected by matching four things:

Zone — determines the equipment protection level required.

Gas group or dust group — the ignition characteristics of the specific substance.

Temperature class — the maximum surface temperature must stay below the ignition temperature of the substance.

Protection technique — the engineering method used.

Common protection techniques to recognise:

  • Marking Technique Principle
  • Ex d Flameproof Contains any internal explosion and cools escaping gases
  • Ex e Increased safety No arcs or hot surfaces in normal operation
  • Ex i Intrinsic safety Energy limited below that needed for ignition (Ex ia, Ex ib)
  • Ex p Pressurisation Clean air or inert gas kept at positive pressure inside
  • Ex n Type of protection "n" For Zone 2, non-sparking in normal operation
  • Ex m Encapsulation Ignition-capable parts encased in compound

An IP rating is not an explosion-protection rating . IP66 tells you about dust and water ingress; it says nothing about whether an internal arc can ignite the surrounding atmosphere. Confusing the two is a classic exam distractor.

Installation Discipline

Use only the certified gland and entry for the equipment type — a flameproof enclosure loses its protection with the wrong gland.

Maintain the specified flamepath dimensions; do not paint, machine or damage flanged joints on Ex d equipment.

Do not substitute fasteners on Ex enclosures; the specified bolts are part of the certification.

Intrinsically safe circuits must be segregated and identified (commonly light blue) and connected through the correct barrier or isolator.

Maintain and record inspection regimes — hazardous area installations require initial and periodic inspection to the relevant standard.

Never modify a certified assembly. Replacing a lamp with a different type, or adding a gland, can void the certification.

The Competence Boundary

The Wiring Rules refer out to the hazardous area standards for classification, selection, installation, inspection and maintenance. Working to those standards requires additional training beyond a Certificate III and an electrical work licence — typically a recognised hazardous area competency covering classification, selection, installation, inspection and maintenance.

The professionally correct position for a newly licensed electrician:

Recognise when an area is or may be classified.

Stop and obtain the classification documentation.

Decline work that is beyond your competency and arrange a competent person.

Never install ordinary equipment in a classified area on the basis that it "looks well sealed."

That answer — recognise, stop, escalate — is what EPC 28 is testing.