Study guide
7.1 Riding Curves: Look, Slow Down and Move Away
Queensland Motorcycle Knowledge Test Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Overview & Queensland Licensing Pathway
1.1 Queensland Motorcycle Knowledge Test: Format, Eligibility and Logistics 1.2 Queensland Motorcycle Licensing Pathway: Q-Ride, Q-SAFE and the HPT 1.3 A Source-Based Study Plan and the Numbers That Cause Errors
2 Queensland Motorcycle Learner Rules & Restrictions
2.1 Learner Supervision, Supervisor Qualifications and the Sidecar Exception 2.2 L Plates, Licence Carriage and Learner Operating Conditions 2.3 Zero BAC, Roadside Drug Testing and Impairment Consequences
3 The Learner Approved Motorcycle Scheme (LAMS) & Equipment
3.1 LAMS Eligibility: Capacity Bands, the Official List and Vehicle Verification 3.2 LAMS Exclusions, Allowable Modifications and Proof of Approval 3.3 Passengers, Sidecars, Loads, Animals and Towing
4 Special Motorcycle Road Rules & Offences
4.1 Lane Filtering and Edge Filtering: Two Different Queensland Rules 4.2 Mobile Phones, Licence-Based Restrictions and Rider Distraction 4.3 Demerit Points, Licence Sanctions and Motorcycle Offences
5 Protective Gear & Pre-Ride Bike Preparation
5.1 Approved Motorcycle Helmets: Standards, Fit and Care 5.2 Protective Clothing, Weather Protection and Visibility 5.3 Motorcycle Controls, Pre-Ride Checks and Maintenance
6 Roadcraft, Hazard Perception & Space Management
6.1 Queensland Roadcraft: Look, Slow Down, Move Away and 12–6–3 6.2 Crash-Avoidance Space, Vision and Stopped Buffers 6.3 Lane Positioning: Space, Surface and Sight 6.4 Rain, Night, Wind, Wildlife and Fatigue
7 Motorcycle Dynamics: Cornering, Braking & Surface Hazards
7.1 Riding Curves: Look, Slow Down and Move Away 7.2 Steering: Direct Steering, Countersteering and Look–Push–Go 7.3 Braking: Set Up and Squeeze, Both Brakes and Emergency Stops 7.4 Surface Hazards and Mechanical Problems While Riding
8 Queensland Road Rules, Speed Limits & Intersections
8.1 Speed Limits, School Zones, Shared Zones and Roadworks 8.2 Giving Way at Crossroads, T-Intersections, Signs and Driveways 8.3 Roundabouts: Giving Way, Lanes and Signals 8.4 Traffic Lights, Signs and Road Markings
9 Road Sharing, Overtaking & Crash Procedures
9.1 Pedestrians, Cyclists, Crossings and Shared Zones 9.2 Heavy Vehicles, Merging, Overtaking and Group Riding 9.3 Crash Duties, Emergency First Aid and Returning to Riding
7.1 Riding Curves: Look, Slow Down and Move Away
Key Takeaways Explain This Topic AI
For curves: Look ahead and plan; Slow down using mirrors, brakes and gears; Move away using start wide, buffer and finish tight.
Complete the main braking and speed selection before entering the curve while the motorcycle is upright.
Maintain at least 6 seconds of vision and slow further when the curve hides the road.
A vanishing point moving toward the rider suggests the curve is tightening; one moving away suggests it is opening.
Buffer the head-on zone and keep both motorcycle and rider clear of the centre line.
Last updated: September 2026
Riding Curves: Look, Slow Down and Move Away
The Queensland Motorcycle Riders’ Guide uses the same hazard tactic for curves that it uses elsewhere: Look, Slow down, Move away . Its key-sequence page expands the curve response:
Look —look ahead and plan the path.
Slow down —check mirrors, apply the brakes and select the gear.
Move away —start wide, buffer the head-on zone and plan to finish tight.
This sequence is the examinable language. It is more reliable than importing a racing acronym or treating “roll on” as an instruction to accelerate regardless of what becomes visible.
Look ahead and through the curve
Scan the approach, surface, traffic, signs and the road beyond. Turn the head and direct vision through the desired path without staring at the edge, an oncoming vehicle or a pothole. Maintain at least 6 seconds of vision ; if the curve hides the road within that time, reduce speed.
The vanishing point is where the road edges appear to meet or disappear. It is a clue, not a throttle command. If it moves away as the motorcycle approaches, the curve is likely opening. If it moves toward the rider, the curve is likely tightening. The rider still checks surface, traffic and actual sight rather than relying on the point alone.
Slow before lean
On the approach, check mirrors so you know what follows. Reduce speed using smooth set-up-and-squeeze braking and select a suitable gear before turning. The brakes work best when the motorcycle is upright and straight; grip available for braking decreases as more grip is used for cornering.
Enter at a speed that permits the path to tighten or the motorcycle to stop within the visible road. If the correct speed is uncertain, slower entry preserves options. Do not coast with the clutch held in. A selected gear provides controlled drive and avoids an unnecessary gear change while leaned.
Start wide, buffer, finish tight
“Start wide” means use a lane position that improves vision and allows a safe line; it never means crossing the centre line or riding on the edge. The exact side depends on the curve direction and hazards.
“Buffer the head-on zone” means keep away from the part of the road an oncoming vehicle may intrude into. Remember that the rider’s head and body can extend closer to the centre line than the tyres when the motorcycle leans. Leave extra space on blind curves.
“Finish tight” means plan the exit toward the inside of the curve within the rider’s lane. It helps control entry speed, preserves room for small errors and places the rider well for a following curve. It is not a racing apex or permission to accelerate beyond the available sight distance.
Steering and acceleration
Use smooth countersteering input to establish and adjust lean. Look in the direction of travel and keep arms relaxed. As the motorcycle begins to straighten on exit and the view is clear, apply smooth acceleration. Too much throttle too early can make the motorcycle run wide.
If the curve tightens unexpectedly, look through the safer path, smoothly increase steering pressure and reduce drive without abrupt closing or braking. If substantial braking becomes unavoidable and space permits, reduce lean and straighten before applying strong brake pressure.
Camber and surface
Camber is the slope across the road. Positive camber generally supports the turn; negative camber slopes away, reducing ground clearance and usable grip. Queensland roads often have a crown, so left and right curves can present different camber. Surface contamination, repaired bitumen, gravel, wet paint and shade can change grip within a single curve.
Adjust the approach speed for the least favourable part you can see. Avoid sudden position changes to miss a small patch if the new path creates a larger traffic hazard.
Series of curves
Treat each visible section separately. Finishing one curve tight may create the appropriate wide entry for the next, but only when space, surface and sight support it. Do not accelerate simply because the first bend opens if the next bend or a crest removes vision.
The low-risk priority is margin: speed selected early, at least six seconds of vision, separation from the head-on zone, and a path that can be adjusted when the road does something unexpected.