Study guide
7.4 Surface Hazards and Mechanical Problems While Riding
Queensland Motorcycle Knowledge Test Exam
Track your progress as you read
Finished sections get a check mark.
1 Exam Overview & Queensland Licensing Pathway
1.1 Queensland Motorcycle Knowledge Test: Format, Eligibility and Logistics 1.2 Queensland Motorcycle Licensing Pathway: Q-Ride, Q-SAFE and the HPT 1.3 A Source-Based Study Plan and the Numbers That Cause Errors
2 Queensland Motorcycle Learner Rules & Restrictions
2.1 Learner Supervision, Supervisor Qualifications and the Sidecar Exception 2.2 L Plates, Licence Carriage and Learner Operating Conditions 2.3 Zero BAC, Roadside Drug Testing and Impairment Consequences
3 The Learner Approved Motorcycle Scheme (LAMS) & Equipment
3.1 LAMS Eligibility: Capacity Bands, the Official List and Vehicle Verification 3.2 LAMS Exclusions, Allowable Modifications and Proof of Approval 3.3 Passengers, Sidecars, Loads, Animals and Towing
4 Special Motorcycle Road Rules & Offences
4.1 Lane Filtering and Edge Filtering: Two Different Queensland Rules 4.2 Mobile Phones, Licence-Based Restrictions and Rider Distraction 4.3 Demerit Points, Licence Sanctions and Motorcycle Offences
5 Protective Gear & Pre-Ride Bike Preparation
5.1 Approved Motorcycle Helmets: Standards, Fit and Care 5.2 Protective Clothing, Weather Protection and Visibility 5.3 Motorcycle Controls, Pre-Ride Checks and Maintenance
6 Roadcraft, Hazard Perception & Space Management
6.1 Queensland Roadcraft: Look, Slow Down, Move Away and 12–6–3 6.2 Crash-Avoidance Space, Vision and Stopped Buffers 6.3 Lane Positioning: Space, Surface and Sight 6.4 Rain, Night, Wind, Wildlife and Fatigue
7 Motorcycle Dynamics: Cornering, Braking & Surface Hazards
7.1 Riding Curves: Look, Slow Down and Move Away 7.2 Steering: Direct Steering, Countersteering and Look–Push–Go 7.3 Braking: Set Up and Squeeze, Both Brakes and Emergency Stops 7.4 Surface Hazards and Mechanical Problems While Riding
8 Queensland Road Rules, Speed Limits & Intersections
8.1 Speed Limits, School Zones, Shared Zones and Roadworks 8.2 Giving Way at Crossroads, T-Intersections, Signs and Driveways 8.3 Roundabouts: Giving Way, Lanes and Signals 8.4 Traffic Lights, Signs and Road Markings
9 Road Sharing, Overtaking & Crash Procedures
9.1 Pedestrians, Cyclists, Crossings and Shared Zones 9.2 Heavy Vehicles, Merging, Overtaking and Group Riding 9.3 Crash Duties, Emergency First Aid and Returning to Riding
7.4 Surface Hazards and Mechanical Problems While Riding
Key Takeaways Explain This Topic AI
Identify gravel, sand, paint, metal, oil, diesel, water, potholes and road edges early; reduce speed before reaching them and cross as upright and smoothly as possible.
For a wobble, keep a firm relaxed grip, roll off gradually, brake progressively, stop and correct the cause before continuing.
For a puncture or blow-out, keep straight, avoid braking if possible, roll off gradually and coast to a safe stop.
For a stuck throttle, pull the clutch, brake progressively, move off the road and use the engine-stop switch and ignition.
Mechanical trouble is a stop-and-fix event; do not continue until the cause and roadworthiness are resolved.
Last updated: September 2026
Surface Hazards and Mechanical Problems While Riding
Motorcycle tyres have small contact patches, so a short strip of gravel, oil or paint can affect both tyres at once. The first defence is early observation. Look well ahead, choose a cleaner path and reduce speed while the motorcycle is upright. Once on the hazard, keep controls smooth and avoid asking the tyres to brake, accelerate and turn sharply at the same time.
Common surface hazards
Loose gravel, sand and roadworks: slow before the loose material, keep the head up and arms relaxed, use smooth throttle and steering, and allow the motorcycle small natural movements without fighting it. Increase the gap from other traffic.
Wet paint and metal: road markings, covers, plates and rails can be slippery when wet. Cross as upright as practical with steady controls. Where a rail or groove must be crossed, use a sufficiently direct angle to prevent the tyre tracking along it, but do not make an abrupt 90-degree swerve into traffic. The safe angle depends on the road and available space.
Oil, diesel and bitumen: look for sheen, staining and spills near intersections, roundabouts and fuel locations. Avoid them where possible. Reduce speed before the contaminated area; do not brake or accelerate sharply on it. Hot-weather bitumen can soften, but no single friction value applies to every repair.
Potholes, corrugations and edges: choose a path early. If a sharp obstacle cannot be avoided, slow beforehand, approach as squarely as traffic permits and keep the motorcycle stable. Be careful when moving from a sealed surface onto a shoulder: check for a drop at the bitumen edge, sand, mud and a safe stopping area.
Wobble
A wobble may be caused by speed, load distribution, tyre condition, pressure, bearings or another mechanical problem. The guide advises:
- keep a firm grip without locking the arms or fighting the steering;
- gradually roll off the throttle;
- gradually apply the brakes and move to the roadside; and
identify and fix the cause before continuing.
Avoid an abrupt steering correction or acceleration. A motorcycle that has wobbled needs inspection, not another high-speed trial.
Skids
Remove the cause. If excessive braking locks a wheel, ease the brake so the wheel can rotate and reapply smoothly after stability returns. If acceleration or speed causes the skid, ease the throttle and slow. Prevention—appropriate speed, smooth inputs, sound tyres and adequate space—is safer than relying on skid recovery.
Puncture or blow-out
A flat front tyre can make steering heavy; a flat rear can make the back weave. Keep a firm grip and travel straight. Avoid brakes if possible. If braking is necessary, use the brake on the tyre that remains sound because braking the failed tyre can separate it from the rim. Move weight back for a front failure or forward for a rear failure, roll off gradually, then coast to a safe roadside stop.
Stuck throttle
If the throttle sticks:
- pull the clutch in to disconnect drive;
- apply the brakes progressively and move to the roadside;
- use the engine-stop switch; and
turn off the ignition.
Keep steering control and do not reach for the key in a way that locks the steering. Do not restart until the cause is repaired.
Broken clutch cable, chain or seized engine
With a broken clutch cable while moving, slow and downshift as speed permits, selecting neutral before stopping. If stopped with the clutch engaged, hold the brakes to stall the engine.
A broken chain may leave the motorcycle freewheeling or may lock the rear wheel. If it freewheels, roll off, brake smoothly and move roadside. If the rear locks, steer into the skid, roll off and coast roadside as speed falls.
If an engine begins to seize, loss of power or an abnormal sound may provide warning. Pull the clutch to disconnect the engine, brake smoothly, move roadside and switch off. Allow it to cool and have the cause corrected; merely adding fluid is not proof the motorcycle is safe.
Emergency roadside exit
Check the shoulder surface, mirrors and blind spot; signal; leave at an appropriate speed; and stop well away from traffic. Mud, sand, a steep drop and the bitumen edge can turn the exit into a crash. Make the motorcycle visible without standing in an active lane.
The knowledge-test response is consistent: smooth control, reduce drive, preserve direction, stop safely and fix the cause before riding again.