Study guide

5.1 Approved Motorcycle Helmets: Standards, Fit and Care

Queensland Motorcycle Knowledge Test Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview & Queensland Licensing Pathway

1.1 Queensland Motorcycle Knowledge Test: Format, Eligibility and Logistics 1.2 Queensland Motorcycle Licensing Pathway: Q-Ride, Q-SAFE and the HPT 1.3 A Source-Based Study Plan and the Numbers That Cause Errors

2 Queensland Motorcycle Learner Rules & Restrictions

2.1 Learner Supervision, Supervisor Qualifications and the Sidecar Exception 2.2 L Plates, Licence Carriage and Learner Operating Conditions 2.3 Zero BAC, Roadside Drug Testing and Impairment Consequences

3 The Learner Approved Motorcycle Scheme (LAMS) & Equipment

3.1 LAMS Eligibility: Capacity Bands, the Official List and Vehicle Verification 3.2 LAMS Exclusions, Allowable Modifications and Proof of Approval 3.3 Passengers, Sidecars, Loads, Animals and Towing

4 Special Motorcycle Road Rules & Offences

4.1 Lane Filtering and Edge Filtering: Two Different Queensland Rules 4.2 Mobile Phones, Licence-Based Restrictions and Rider Distraction 4.3 Demerit Points, Licence Sanctions and Motorcycle Offences

5 Protective Gear & Pre-Ride Bike Preparation

5.1 Approved Motorcycle Helmets: Standards, Fit and Care 5.2 Protective Clothing, Weather Protection and Visibility 5.3 Motorcycle Controls, Pre-Ride Checks and Maintenance

6 Roadcraft, Hazard Perception & Space Management

6.1 Queensland Roadcraft: Look, Slow Down, Move Away and 12–6–3 6.2 Crash-Avoidance Space, Vision and Stopped Buffers 6.3 Lane Positioning: Space, Surface and Sight 6.4 Rain, Night, Wind, Wildlife and Fatigue

7 Motorcycle Dynamics: Cornering, Braking & Surface Hazards

7.1 Riding Curves: Look, Slow Down and Move Away 7.2 Steering: Direct Steering, Countersteering and Look–Push–Go 7.3 Braking: Set Up and Squeeze, Both Brakes and Emergency Stops 7.4 Surface Hazards and Mechanical Problems While Riding

8 Queensland Road Rules, Speed Limits & Intersections

8.1 Speed Limits, School Zones, Shared Zones and Roadworks 8.2 Giving Way at Crossroads, T-Intersections, Signs and Driveways 8.3 Roundabouts: Giving Way, Lanes and Signals 8.4 Traffic Lights, Signs and Road Markings

9 Road Sharing, Overtaking & Crash Procedures

9.1 Pedestrians, Cyclists, Crossings and Shared Zones 9.2 Heavy Vehicles, Merging, Overtaking and Group Riding 9.3 Crash Duties, Emergency First Aid and Returning to Riding

5.1 Approved Motorcycle Helmets: Standards, Fit and Care

Key Takeaways Explain This Topic AI

Every rider and passenger must wear an approved helmet that is correctly fitted and securely fastened.

Queensland accepts AS1698, AS/NZS1698 and UN ECE 22.05 or 22.06 compliant motorcycle helmets.

An approved helmet carries the required compliance label or mark; a DOT- or Snell-only helmet is not enough.

Eye protection and a full-face design are strong safety recommendations, but do not invent a separate visor standard as a universal Queensland riding law.

After an impact, suspected damage or manufacturer-specified service life, obtain expert advice or replace the helmet; do not rely on an unsupported universal 3–5-year law.

Last updated: September 2026

Approved Motorcycle Helmets: Standards, Fit and Care

Queensland law requires every motorcycle rider and passenger to wear an approved motorcycle helmet. The helmet must be correctly fitted and securely fastened. The legal rule applies on short trips as well as long ones, and a rider carrying a passenger must ensure that passenger also complies.

Approved standards

The current motorcycle road-rules page accepts helmets complying with:

  • Australian Standard AS1698 ;
  • Australian/New Zealand Standard AS/NZS1698 ; or

United Nations ECE 22.05 or 22.06 .

The standard in force when the helmet was purchased and the correct certification mark matter. The Motorcycle Riders’ Guide illustrates an Australian standards label and an ECE label; an ECE approval mark may use an “E” followed by an approval-country number. A helmet certified only to a United States DOT or Snell standard is not established as Queensland-approved unless it also carries an accepted Australian or ECE approval.

Fit and fastening

A helmet should be snug all around without pressure points that become painful. It should not rotate freely on the head or lift away when the chin bar or rear is moved. Fasten the retention system according to the manufacturer’s instructions and tighten it so the strap cannot slip over the chin.

A fastened but badly fitting helmet may move in a crash; an approved but unfastened helmet may come off. Approval, fit and fastening are separate checks. Never place a thick cap or bulky object under the helmet if it compromises fit.

The current demerit schedule assigns 3 points when a rider fails to wear an approved helmet and 3 points when a rider fails to ensure the passenger wears one. A passenger can also be penalised. Qualifying repeat motorcycle-helmet offences within 1 year attract Queensland’s all-year double-demerit rule.

Helmet styles and eye protection

Full-face helmets provide the broadest coverage of the face and jaw. Modular, open-face and other designs vary in coverage and must be used in the configuration authorised by their certification and manufacturer. Do not assume that a movable chin bar is protective in an open position unless the helmet is approved for that use.

The rider guide recommends a clear, shatterproof, unscratched visor for night riding and suitable eye protection. Wind, insects, stones and rain can destroy vision at speed. Tinted protection reduces night vision and should not be used when it prevents the rider from seeing clearly. These are crucial safety practices, but a study guide should not invent a universal Queensland “AS1609 visor offence” when the official motorcycle rule being tested is the approved, fitted and fastened helmet.

Inspection and replacement

Before use, inspect the shell, liner, strap, buckle, visor and mounting points. Do not drill the shell, attach hardware with unsuitable adhesive, paint it with incompatible products or expose it to fuel and solvents. Store it where heat, sunlight and chemicals will not degrade it.

After a crash or significant impact, damage to the energy-absorbing liner may be invisible. Follow the manufacturer’s replacement advice and replace the helmet when impact damage is possible. If it is merely dropped while empty, inspect it and consult the manufacturer if uncertain; do not state that every small drop has the same effect as a loaded crash.

Manufacturers specify service and replacement guidance based on materials and use. Sweat, UV exposure, compressed comfort padding and strap wear can all matter. Queensland does not create a single statutory rule that every helmet becomes illegal after three or five years. Use the manufacturer’s interval and replace earlier for damage, poor fit or failed components.

Buying and using a helmet

Verify the accepted compliance label before purchase.

Try the correct size and shape; brand sizes differ.

Check that the visor gives a clear field of view and works with glasses if needed.

Fasten it every time before moving.

Never buy a used helmet if its impact history and condition cannot be established.

Carry passengers only with an approved, properly fitted and fastened helmet for them.

For an exam scenario, check standard, label, fit and strap. Coverage and care improve safety, but they should not be confused with unsupported legal claims.

Borrowing a helmet is acceptable only if the approval, condition, size and fit can all be confirmed. A helmet that fitted its owner may move excessively on another rider. Before carrying a passenger, adjust the passenger’s strap and ask them to move the helmet gently to confirm it remains secure; the rider retains responsibility for the passenger’s approved helmet.